Sharif Digital Repository

The present work studied bioactive coatings on the surface of ceramic biomaterials. Zirconia toughened alumina (ZTA) composites containing 15 mol.-%. Partially stabilised zirconia was prepared after 1 h sintering at 1550°C. Apatite layers were then coated onto the surfaces of composites by the biomimetic method using 1·5-2 multiply concentrations of simulated body fluid (SBF). Before treatment in SBFs, a sodium silicate layer was employed as nucleating agent to induce the formation of a calcium phosphate layer. The effect of immersion time on the morphology of the precipitate was monitored with a scanning electron microscope. X dot maps revealed that there is a relationship between... 

In this work successful synthesis of multiwall carbon nanotube (CNT) using solution combustion and chemical vapor deposition (CVD) methods are reported. Ceramic nanocomposite samples of (Al 2-xFe xO 3)-(y)ZrO 2 formula with x = 0.017, 0.034 and 0.17 and y = 0.15 were initially prepared. These were then subjected to CVD process during which the in situ reduction of iron oxide to metallic iron (Fe/Fe 3C) phase/s provided the necessary catalyst for the CNT formation. The formation of long flexible filaments with a smooth and regular surface bridging between alumina-zirconia (AZ) grains could be detected. The diameters of the formed filaments were in the range of ∼70 to ∼320 nm and length of the... 

Nanocomposites of Ce-TZP/Al 2O 3 were synthesized by aqueous combustion, and urea, ammonium acetate and glycine were used as mixtures of fuels with the corresponding metal nitrates. Thermodynamic modeling was conducted to anticipate the effect of the alumina content on the exothermicity of the combustion procedure. The thermodynamic properties of the combustion reaction indicated that as the alumina content increased, the amount of gases produced during the reaction increased with a decrease in the adiabatic temperature. Furthermore, to reduce the particle size of the powders, a series of combustion reactions were performed to optimize the fuel composition and alumina content. Ce 0.1Zr 0.9O... 

Alumina-zirconia nanostructured coatings were formed on 7075 Al alloy through Plasma Electrolytic Oxidation (PEO) operated in aDC potentiostatic mode. The composite coatings were produced in the range of 425-500 V in an alkaline electrolyte containing 4 g/LK2ZrF6. Tribological properties of coatings were investigated using dry sliding wear test against WC balls with a pin-on-disc tribometer. Wear rates were evaluated using optical profilometer. It was shown that the nanostructured alumina-zirconia composite coatings can be formed at voltages 450 V. The coating thickness and roughness were in the range of 15.2-24.2 μm and 0.68-2.35 μm, respectively. The distribution of Al, Zr and O in the... 

The mechanism of interface formation during sinter-joining of nanostructured yttria stabilized zirconia (27 nm) compacts with chromium powder was investigated. The effect of sintering atmosphere, i.e. argon or vacuum, was studied. Microstructural evaluation and phase formation was examined by scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), and micro-focused X-ray diffraction (MFXRD) methods. It is shown that spreading and evaporation-condensation mechanisms are responsible for the interface formation. An improved joint shear-strength was obtained after sintering in vacuum (74 MPa) compared with argon (41 MPa). The result of MFXRD indicated formation of Cr-island at... 

Copper matrix composites have received more attentions as possible candidate for thermal and electrical conductive materials to be used in electrical contact applications. In this study, five-layered Cu/YSZ (yttria-stabilized zirconia) functionally graded material (FGM) and copper matrix composite specimens containing 3 and 5 vol% YSZ particles plus pure Cu specimen were synthesized using powder metallurgy (PM) route and spark plasma sintering (SPS) consolidation process. The microstructural and some physical, mechanical features of all specimens were characterized. Microscopic examinations showed that ultrafine YSZ particles were distributed in the copper matrix almost homogeneously. An... 

In the present work, the hot corrosion behavior of two types of multilayer plasma sprayed TBC were investigated and compared with functionally graded and conventional TBCs. These kinds of multilayer coatings consisted of nano/μ alumina as a top coat on YSZ layer, a metallic bond coat and a functionally graded intermediate layer deposited between YSZ and bond coat layers. All the layers were sprayed on the Ni-base super alloy substrate. The hot corrosion resistance of the plasma sprayed coatings was examined at 1050 °C for 40 h, using a fused mixture of 45 wt% Na2SO4 + 55wt%V2O5. Before and after hot corrosion, the microstructure and phase analysis of the coating were studied using scanning... 

In the present work, spark plasma sintering (SPS) process was employed to prepare a nanostructured yttria-stabilized zirconia (8YSZ) coating on a nickel-based superalloy (INCONEL 738) with functionally graded structure. A stack layer of INCONEL 738/NiCrAlY powder/Al foil/NiCrAlY+YSZ powder/YSZ powder was SPSed in a graphite die at an applied pressure of 40 MPa under an vacuum atmosphere (8 Pa). The sintering temperature was ∼1040 °C. For comparison purpose, the air plasma spray (APS) technique was employed to prepare the thermal barrier coating (TBC). Microstructural studies by scanning electron microscopy showed that the SPSed coating was sound and free of interfacial cracks and large... 

In this research study, a comparative evaluation of the additional impact of nanometer-sized tetravalent oxides [Zirconia (ZrO2), Titania (TiO2), and Silica (SiO2)] on the properties and performance of Doloma-Magnesia (MgO-CaO) ceramic refractories, with an emphasis on their hydration resistance improvement, has been done. For this purpose, from 0 to 2.5 wt% ZrO2, TiO2, and SiO2 nanometer-sized particles have been added to the Doloma-Magnesia compositions. After formulation and mixing of the starting materials, the pressed samples (at 150 MPa) were tempered (at 250 °C for 12 h) and fired in a shuttle furnace (at 1650 °C for 3 h). The physical, mechanical, and thermo-mechanical properties of... 

Medical engineering advances in total joint replacements and societies’ rising demand for long-lasting materials have proven it essential to manufacture materials that are more similar to the original tissue in the fields of mechanical, tribological, and biological properties. Ultra-high molecular weight polyethylene (UHMWPE) is a polymer widely used in arthroplasty applications due to its biocompatibility, chemical stability, and reasonable mechanical properties; however, it still fails to entirely meet the standards of the hip joint implant. In this study, different concentrations of nanosized zirconia were added to UHMWPE and HAp matrix with an intended application in arthroplasty.... 

Medical engineering advances in total joint replacements and societies’ rising demand for long-lasting materials have proven it essential to manufacture materials that are more similar to the original tissue in the fields of mechanical, tribological, and biological properties. Ultra-high molecular weight polyethylene (UHMWPE) is a polymer widely used in arthroplasty applications due to its biocompatibility, chemical stability, and reasonable mechanical properties; however, it still fails to entirely meet the standards of the hip joint implant. In this study, different concentrations of nanosized zirconia were added to UHMWPE and HAp matrix with an intended application in arthroplasty.... 

In this study, zirconia antistatic coatings were synthesized by a simple dip coating sol-gel route on glass substrates, then applied to polymer-based composites to potentially improve their dust or water repellent capabilities. The coating solution contained a precursor (ZrCl4), solvent (isopropanol) and coupling agent. FTIR spectra confirmed ZrO2 and ZrO compounds in both solution and antistatic coating. FE-SEM images indicated ZrO2 fibers’ thickness was controlled by changing ZrCl4 concentration (150 g–15 g ZrCl4/l) or relative humidity (20%–60%) during coating drying. Fibers grew thicker when decreasing the former or increasing the latter. The surface electrical resistivity for all... 

We report on the response of a monolithic high Tc transition-edge bolometer to about 3 mmWave for the first time. The detector structure consisting of 400-nm YBa2Cu3O7-x(YBCO) film on buffered yttria stabilized zirconia substrate without any coupled antenna, shows bolometric type responsivity to the 3-mmWave radiation at its transition temperature. The YBCO thin film Ce0.9La0.1O2 buffer layer are both fabricated by the metal-organic deposition method. The meander line pattern of the bolometer is designed for obtaining maximum absorption and responsivity possible when the polarized radiation of the source is aligned with the pattern. Meander lines are 50 micrometers wide and 1.5-mm long. We...