Sharif Digital Repository

In this work, the flow stress behavior of a metal matrix composite AA2017-10% SiCp was studied by means of the uni-axial compression test. The composite was first produced by stir casting technique and then, hot extrusion with the ratio of 18:1 was carried out to achieve a microstructure with a homogeneous distribution of SiC particles. In the next stage, the isothermal compression tests were conducted on the cylindrical specimens up to the true strain of 0.6. The experiments were performed at temperatures between room temperature to 400°C and strain rates of 0.003, 0.03 and 0.3s-1. Negative strain rate sensitivity was observed in the temperatures less than 250°C indicating the occurrence of... 

In this research, the occurrence of dynamic strain aging (DSA) phenomenon during equal channel angular extrusion (ECAE) of a commercial air cooled Al-Mg-Si-Cu alloy is investigated. In order to detect the negative strain rate sensitivity behaviour associated with DSA, samples were ECAE-ed at various temperatures and strain rates. Subsequently, the extruded billets were subjected to mechanical and physical tests and it was found that at a certain ECAE temperature range there is a critical strain rate above which DSA occurs. The implication of the results to strengthening of dilute solid solutions is discussed  

In this work, the phenomenon of dynamic strain aging in a high carbon steel is studied and different initial microstructures including fine and coarse pearlite structures are considered. Tensile tests at different temperatures and strain rates are performed to evaluate the occurrence of dynamic strain aging and mechanical properties as well as to calculate apparent activation energies for onset and termination of dynamic strain aging. The results show that dynamic strain aging occurs for both microstructures while the initial microstructures alters the activation energies for appearance and termination of this phenomenon. The microstructural studies illustrate that a combination of cementite... 

The microstructure of cold rolled Al–6Mg alloy is investigated after two steps annealing at different coupled temperatures of 250–320 °C and 320–400 °C for various times. Dynamic strain aging behavior in terms of serrated flow and strain rate sensitivity is investigated. The effect of three microstructural features, cell structure, recovered and recrystallized microstructures, on the strain rate sensitivity is elucidated. Two steps annealing process is utilized to capture the effect of recovery and precipitation phenomena on recrystallization and dynamic strain aging behaviors. The results show that the negative strain rate sensitivity of cold rolled specimen increases to positive values in... 

High bainite dual phase steel has been subjected to tension test at different temperatures from 25 to 500 °C with strain rate of 4.6 × 10-4 s-1 to investigate the effect of temperature on its mechanical properties. Stress-strain curves of steels showed serration flow at temperature range of 200-350 °C and smooth flow at the other temperatures. In agreement with previous studies on some steels, peaks in the variations of yield strength (YS) and ultimate tensile strength (UTS) and minima in ductility were observed at temperature range of 200-350 °C which are various manifestations of dynamic strain aging (DSA). It has been also found that ferrite volume fraction has no effect on the... 

Artificial neural network (ANN) and genetic algorithm were used in this study to obtain a relatively high flow stress in compression tests for 304 stainless steel. Cold and warm compression were carried out in a temperature range from 20 to 600 °C, strain-rate from 0.001 to 100 S-1 and a strain range from 0.1 to 0.5. Optimum conditions for each case were obtained experimentally and were evaluated by the ANN model. The ANN model was used as fitness function for genetic algorithm. The results indicated that this combined algorithm offers an effective condition for 304 stainless steel, which avoids flow localization, dynamic strain aging, adiabatic shear deformation and void generation. © 2005... 

A two-dimensional finite element analysis is coupled with dynamic recovery and dynamic strain aging models to achieve metal flow during warm deformation of a low carbon steel. In order to assess metal behavior, compression experiments are utilized under warm deformation conditions and the results are used in the model and temperature and velocity fields are predicted with regard to the effects of dynamic recovery and dynamic strain aging. In addition, warm rolling tests are performed to verify the modelling results. Comparison between the predicted and measured roll forces shows reliability of the employed model. © 2005 Elsevier Ltd. All rights reserved  

In this work, the 6061 aluminum alloy tubes are severely deformed through a novel method called Tube Channel Pressing (TCP). The ability of this process in improving mechanical properties, grain refinement and microstructural changes of the alloy with different heat treatments before and after TCP process is investigated. Results show that TCP has notable effect on grain refinement and decreases crystallite size of solid solution treated aluminum 6061 material to 52. nm after equivalent strain of 3.09 which is comparable with the measured data from other SPD processes. The strength of the specimens aged before TCP is higher than that of those aged after TCP. The specimens artificially aged... 

In this study, the kinetics of aging in AA6061 and AA6061 with 5% volume fraction SiCp were studied and compared. The composite was first produced and homogenized using stir casting technique followed by hot extrusion with the ratio of 18:1. Then, both AA6061 and the composite were aged at three different temperatures including room temperature, 170 °C and 240 °C, while mechanical properties during aging were evaluated employing hardness measurements and tensile testing. Moreover, in order to assess the effect of plastic deformation on the kinetics of aging, a series of samples were first deformed by equal-channel angular pressing immediately after solution treatment and then aged in the... 

AISI 4340 steel bars were heated at 900 °C for one hour, annealed at 738 °C for different durations and oil-quenched in order to obtain dual phase steels with different ferrite volume fractions. A 3% prestrain at the temperature range of 150-450 °C was then imposed to the samples, and room temperature tensile tests were carried out, afterwards. Results indicate that the maximum values for both yield and ultimate tensile strength would exist for the samples pre-strained at the temperature range of 250-300 °C. Also, a sudden drop of the ductility was observed at the mentioned temperature range. The observed behavior might be attributed to the occurrence of dynamic strain aging taken place at... 

High-bainite dual phase (HBDP) steels with 34. vol.% ferrite were subjected to tensile strains of 1%, 3%, and 5% at intermediate temperatures (150-450. °C). Mechanical behavior of pre-deformed steels was then investigated at room temperature. A maximum value for both yield stress and ultimate tensile strength was observed for pre-deformed steels. A minimum elongation was also found in the same pre-deformed specimens at the range of 250-350. °C. It was found that dynamic strain aging (DSA) plays the major role in mechanical properties of pre-strained HBDP steels. The DSA indicator parameter (DSAP) was introduced to evaluate DSA mechanism. Maxima of DSAP were likewise observed at the range of... 

In the present research, the effect of residual stress distribution on the static strain aging (SSA) phenomenon in cold rolled steel was investigated. A three-dimensional model was employed to evaluate the residual stress distributions within the rolled strips, and hole drilling experiments were also performed to verify the data obtained from the mathematical model. Hardness and tensile tests were then performed on the cold rolled samples at different temperatures and aging periods, and the results of these tests were utilised to assess SSA behaviour after different rolling programs. The results show that SSA occurs within the cold rolled steel in the employed aging period, and its kinetics... 

In this study, static strain aging behaviour of cold rolled steel strips was considered with emphasis on the distribution of residual hydrostatic stress developed during temper rolling. In order to assess residual stress distribution produced by the temper rolling, a three-dimensional model was first employed. Then, samples were rolled at a reduction of 4% under single and double pass rolling programmes and the kinetics of static strain aging phenomenon as well as the required activation energies were then evaluated using hardness and tensile tests on the deformed samples. Considering the predicted residual hydrostatic stress distribution, it was found that tensile hydrostatic stresses... 

In this study, the plastic instabilities associated with the Portevin-Le Chatelier (PLC) and their effects on the mechanical properties and the fracture surfaces have been investigated for AA 5083. Tensile tests were performed at various temperatures and strain rates in order to do so. Then, serrated and smooth yielding domains were determined in Ln ε̇-1/T diagram. The stress-strain curves related to the serrated domain show the values of flow stress decreases by increasing the strain rate at a constant temperature. In addition, the plot of critical strain versus imposed strain rate indicates an inverse manner at very low strain rates. It is confirmed that the type of PLC bands alters the... 

Dual-phase (DP) steels with different martensite contents were produced by subjecting a low carbon steel to various heat treatment cycles. In order to investigate the effect of dynamic strain aging (DSA) on mechanical properties, tensile specimens were deformed 3% at 300 °C. Room temperature tensile tests of specimens which deformed at 300 °C showed that both yield and ultimate tensile strengths increased, while total elongation decreased. The fatigue limit increased after pre-strain in the DSA temperature range. The effects of martensite volume fraction on mechanical properties were discussed  

In this work, static strain aging behavior of an alloy steel containing high amounts of silicon and manganese was examined while the influences of initial microstructure and pre-strain on the aging kinetics were evaluated as well. The rate of strain aging in a low carbon steel was also determined and compared with that occurred in the alloy steel. The rates of static strain aging in the steels were defined at room temperature and at 95 °C by means of double-hit tensile testing and hardness measurements. In addition, three-stage aging experiments at 80 °C were carried out to estimate aging behavior under multi-pass deformation processing. The results showed that in-solution manganese and... 

Dual phase (DP) steels with network and fibrous martensite were produced by intercritical annealing heat treatment cycles. Some of these steels were deformed at dynamic strain aging temperatures. Room temperature tensile tests of specimens deformed at 300 °C showed that both yield and ultimate tensile strengths for both morphologies increased, while total elongation decreased. Fatigue test results before and after high temperature deformation showed that dynamic strain aging has a stronger effect on fatigue properties of dual phase steels with fibrous martensite. Cracks in DP steels with fibrous martensite propagate in a tortuous path in soft ferrite phase, while they pass of both hard and... 

An integrated model based on finite-element method has been proposed to examine the mechanical and thermal responses of strips and work-rolls in tandem and reverse cold rolling operations. The model has been developed such that the influence of various process parameters, such as lubrication, rolling speed, frictional state and back-up rolls, can be examined. Thermal behaviors of the rolled material and the work-rolls have been analyzed using stream-line upwind Petrov-Galerkin approach, in order to make the model applicable to high-speed rolling processes, as well. The results have been compared to the actual on-line measurements and shown to be of acceptable accuracy. Such modeling approach...