Sharif Digital Repository

Structural, microstructural and mechanical properties in roll bonding of AA5052 and polypropylene sheets have been evaluated in this study. The surface roughness of the AA5052 sheets, rolling temperature and the surface energy of polymer were selected as the bonding variables. The findings indicated that an increase in the surface energy of polypropylene by grafting maleic anhydride would result in higher bonding strength due to chemical interaction between the AA5052 and the maleic anhydride grafted polypropylene (PP-g-MAH). In fact, this reaction caused the formation of an interphase layer at the polymer side of the interface and the diffusion of aluminum into the PP-g-MAH layer. It was... 

A new method for the fabrication of an electromagnetic nanocomposite based on Fe3O4 and polyaniline (PANI) is offered. The authors focused on improvement of the physical and electromagnetic properties of the nanocomposite using a new synthetic method. Supermagnetic Fe3O4 nanoparticles were synthesized through coprecipitation method. As a chemical modification, the third generation of poly (amidoamine) dendrimer was grafted on the surface of the nanoparticles. PANI was grafted from -NH2 functional groups of dendrimer via in situ polymerization of aniline. Finally, Au nanoparticles were loaded on the nanocomposite and its catalytic activity for reduction reactions was studied  

Structural, microstructural and mechanical properties in roll bonding of AA5052 and polypropylene sheets have been evaluated in this study. The surface roughness of the AA5052 sheets, rolling temperature and the surface energy of polymer were selected as the bonding variables. The findings indicated that an increase in the surface energy of polypropylene by grafting maleic anhydride would result in higher bonding strength due to chemical interaction between the AA5052 and the maleic anhydride grafted polypropylene (PP-g-MAH). In fact, this reaction caused the formation of an interphase layer at the polymer side of the interface and the diffusion of aluminum into the PP-g-MAH layer. It was... 

Zinc oxide nanoparticles were synthesized and modified by a three-stage method. Elemental analysis, Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning and transmission electron microscopy, and Brunauer–Emmett–Teller method were applied to characterize the nanoparticles. These nanoparticles were evaluated for toluene adsorption from aqueous solutions as a representative of petroleum hydrocarbon removal. The optimum adsorption condition achieved at pH of 6 and contact time of 30 min. The adsorption isotherms were fitted to the Langmuir model. The measured adsorption capacity was 12.8 mg g−1. This study demonstrated that these nanoparticles could be used as an... 

Magnetic reduced graphene oxide/polymer nanocomposites were prepared by in situ polymerization and grafting of polyacrylamide on the surface of functionalized magnetic reduced graphene oxide (rGO). Graphene oxide nanosheets were decorated with Fe3O4 nanoparticles, reduced and functionalized with 3-(trimethoxysilyl)propyl methacrylate, and then grafted with polyacrylamide. Grafting of polyacrylamide makes magnetic rGO hydrophilic and highly water dispersible. The prepared material was used as adsorbent for removal of an anionic dye, Congo red, and a maximum adsorption capacity up to 166.7 mg g−1 was obtained. The kinetics and isotherm of adsorption and the effect of experimental condition on... 

Incorporating titanium dioxide (TiO2) nanoparticles into the polymeric matrix offers an opportunity to obtain nanocomposites with improved functionality. In this study, the commercial TiO2 nanoparticles (TNP) were surface treated by different concentrations of aminopropyl triethoxy silane (APTS) as a coupling agent and triethylamine (Et3N) as a surface grafting catalyst by an aqueous process to prepare a nanocomposite with superior properties. Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA) were performed to confirm the successful surface modification of TNP. The prepared modified TiO2 nanoparticles (mTNP) with different weight fractions were used as... 

In this research, polysulfone (PSf) ultrafiltration (UF) membranes were prepared by a phase inversion method. Surface modification of the PSf membranes was carried out via grafting of acrylic acid as a hydrophilic monomer by free radical graft polymerization initiated by redox reaction. A central composite design (CCD) of response surface methodology (RSM) was applied to design the experiments. The process variables were acrylic acid concentration (CAA), redox system contact time (T1), and acrylic acid polymerization time (T2), while the contact angle (CA), pure water flux (PWF), and flux recovery ratio (FRR) were considered as the responses. Analysis of variance (ANOVA) demonstrated that... 

The major obstacles in gas separation by mixed-matrix membranes (MMMs) are poor dispersion and poor affinity between polymers and fillers. The present study demonstrates that these challenges can be overcome appropriately by utilizing a series of synthesized stand-alone MMMs. The matrix used was polymethyl methacrylate (PMMA) and the MMMs were synthesized by in situ polymerization of methyl methacrylate (MMA) in the presence of UiO-66, NH2-UiO-66 and vinyl group attached UiO-66. In situ polymerization of MMA in the presence of vinyl attached UiO-66 resulted in PMMA grafted UiO-66 with a high degree of grafting. Microscopic analysis by field emission scanning electron microscopy (FESEM)... 

Mixed-matrix membranes (MMMs) are promising candidates for carbon dioxide separation. However, their application is limited due to improper dispersion of fillers within the polymer matrix, poor interaction of fillers with polymer chains, and formation of defects and micro-voids at the interface of both phases, which all result in the decline of the gas separation performance of MMMs. In this work, we present a new method to overcome these challenges. To this end, a series of MMMs based on polyethersulfone (PES) as the continuous polymer matrix and MIL-53-derived MOFs as the dispersed filler were prepared. FTIR-ATR, XRD, TGA, FESEM, and N2 adsorption/desorption analyses were employed to... 

Graphene oxide (GO) was chemically modified withpara-aminobenzoic acid (PABA) to immobilize copper(ii) ions on its surface and used as a nanocatalyst for the oxidative C(sp2)-H bond amination reaction. A practical method to prepare Cu2+supported onpara-aminobenzoic acid grafted on GO was reported. The prepared Cu2+@GO/PABA was characterized by FT-IR, XRD, SEM, AFM, TEM, UV-Vis, and ICP techniques. The results showed that the morphology, distribution, and loading of copper ions could be well-adjusted by grafting of PABA on GO. Moreover, just 2 mol% of Cu2+@GO-PABA could catalyze the C-H activation reaction of benzoxazole and benzothiazole with secondary amines in >94% yields. Also, the... 

A manganese porphyrin, meso-tetrakis(pentafluorophenyl)porphyrinato manganese(iii) acetate, Mn(TPFPP)OAc, was immobilized on silica-coated magnetic Fe3O4 nanoparticles functionalized with 3-aminopropyltriethoxysilane (APTS) through the amino propyl linkage using a grafting process in toluene solvent. This enabled the covalent immobilization of Mn(iii) porphyrin via an aromatic nucleophilic substitution reaction, to afford the Fe3O4@SiO2-NH2@MnPor catalyst. The resulting nanoparticles were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), FT-IR spectroscopy, UV-Vis spectroscopy, elemental analysis (CHN), atomic absorption spectroscopy (AAS), and vibrating... 

A magnetic nanoparticle@starch-g-poly(vinyl sulfate) nanocomposite (MNP@St-g-PVS) as a new magnetic nano-adsorbent has been prepared based on graft copolymerization of vinyl acetate onto starch in the presence of magnetic nanoparticles, where the acetate groups were converted to hydroxyl groups followed by the sulfation of the hydroxyl groups using chlorosulfonic acid. Characterization of this magnetic nanocomposite was carried out by FTIR, TGA, XRD, VSM, SEM, TEM and elemental analysis. The resulting nanocomposite was used as an adsorbent for the removal of typical cationic dyes, methylene blue (MB) and malachite green (MG), from aqueous solutions. All experimental parameters that can... 

A novel optimized chelating hydrogel was synthesized via graft copolymerization of acrylamide and 2-hydroxyethyl methacrylate (as two-dentate chelating co-monomer) onto salep (a multicomponent polysaccharide obtained from dried tubers of certain natural terrestrial orchids) using N,N′-methylenebisacrylamide as a crosslinker and ammonium persulfate as an initiator. Reaction parameters (N,N′-methylenebisacrylamide and ammonium persulfate amounts as well as acrylamide/2-hydroxyethyl methacrylate weight ratio) affecting the water absorption of the chelating hydrogel were optimized using a systematic method to achieve a hydrogel with high swelling capacity as possible. Heavy metal ion adsorption... 

In this study, maleic anhydride grafted polypropylene microporous flat-sheet membranes were prepared via a thermally induced phase separation method with a mixture of dibutyl phthalate and dioctyl phthalate as a diluent. The effects of the polymer composition and coagulation bath temperature on the morphology and performance of the fabricated membranes were investigated. The hydrophilicity results of the membranes demonstrated that membrane modification reduced the water contact angle by about 45°, whereas the pure water flux was enhanced about four times. The antifouling behavior of the fabricated membranes was also investigated in a membrane bioreactor. The results show that the pure water... 

The purpose of this research is to explain the surface modification of fabricated polyamide reverse osmosis (RO) membranes using UV-initiated graft polymerization at different irradiation times (15, 30, 60, and 90 s) and various acrylamide concentrations (10, 20, and 30 g L−1). Also, coating of membranes surface with various concentrations of TiO2 nanoparticles (10, 20, 30, and 50 ppm) followed by the same UV irradiation times was investigated. After that, the membranes modification was done by grafting of acrylamide blended with TiO2 nanoparticles via UV irradiation. The characterization of membranes surface properties and their performance were systematically carried out. The results... 

The synthesis of nanocomposites via in situ grafting polymerization due to its ability to produce polymeric materials with promising microscopic and macroscopic characteristics is becoming very attractive. In this paper, different poly(L-Lactide)-block-poly(ε-caprolactone) (PLLA-b-PCL) copolymers were in situ synthesized in the presence of modified titanium dioxide (TiO2) nanoparticles (mTNP) as the initiator and stannous octoate as the catalyst. The surface of TiO2 was modified by grafting aminopropyl trimethoxy silane to improve initiator efficiency. Copolymers with 90/10, 70/30, and 50/50 mass ratio of L-lactide/ ε-caprolactone and 5 wt% of mTNP (proportional to ε-caprolactone) were... 

With the high rate of mortality associated with breast cancer among women, breast cancer treatment has attracted great deal of attention globally. To reduce the exposure of body organs to high cytotoxicity of the common chemotherapeutic drugs, local co-delivery of selected chemotherapeutics has emerged as a solution. In this work, an electrospun composite including a co-drug-loaded graphene oxide-based nanocarrier is fabricated for local anticancer applications. To increase dispersion and cellular uptake of graphene oxide (GO), first, the hydroxyl groups at the edges of GO are grafted by poly (epichlorohydrin) (PCH) to form GO-PCH. Then, the hydroxyl end groups of PCH are grafted (g) with... 

Microbial contamination poses a serious threat to human health. The evaluation of alternative systems and their reliability for the treatment of water is essential. In this work, a new method for the deposit of more silver nanoparticles (AgNPs) on the external surface of Fe3O4 nanoparticles is presented. Fe3O4 nanoparticles were synthesised by chemical co-precipitation and were modified in two stages using 3-mercaptopropyl trimethoxysilane and grafting allyl glycidyl ether and N, N-dimethylacrylamide. Then, AgNPs were loaded onto the modified Fe3O4 to be used for water disinfection. The resulting nanoparticles were characterised by transmission electron microscopy, X-ray powder diffraction,... 

In this article, we synthesize a novel gelatin-based superabsorbent hydrogel via graft copolymerization of mixtures of acrylic acid (AA) and acrylamide (AAm) onto gelatin backbones. The polymerization reaction was carried out in an aqueous medium and in the presence of ammonium persulfate (APS) as an initiator and N,N-methylene bisacrylamide (MBA) as a crosslinker. The hydrogel structures were confirmed by FTIR spectroscopy. The effect of grafting variables, i.e. concentration of MBA and APS, AA/AAm weight ratio, and reaction time and temperature, was systematically optimized to achieve a hydrogel with swelling capacity as high as possible. The swelling behavior of these absorbent polymers... 

A switchable dual light- and temperature-responsive drug carrier using gold nanoparticles (Au NPs)-grafted poly(dimethylacrylamide-co-acrylamide)/poly acrylic acid [P(DMA-co-AAm)/PAAc] hydrogel was prepared by free radical polymerization procedure using N,N-methylenebisacrylamide as cross-linker and ammonium persulfate as initiator. Initial P(DMA-co-AAm) hydrogel and uniformly-distributed stable Au NPs, prepared by reduction of hydrogen tetrachloroaureate (III) hydrate in the presence of trisodium citrate, were synthesized separately. Then, the prepared P(DMA-co-AAm) and Au NPs were added to an acrylic acid solution along with the cross-linker and initiator to prepare PAAc hydrogel within...