Sharif Digital Repository

Hardening and operational measures in electrical distribution systems (EDSs) aim at improving the resilience of EDS in case of natural disasters. This paper proposes a novel two-stage framework for establishing optimal restoration paths for supplying critical loads (CLs) in the aftermath of a natural disaster that will improve the resilience of EDSs. To this end, in the first stage, an algorithm is introduced to find all possible candidate paths between available distributed energy resources (DERs) and CLs, the output of which is applied to the second stage, as the inputs. Subsequently, in the second stage, the problem of finding the optimal restoration paths is modeled as a mixed integer... 

A mathematical model has been proposed to predict flow behavior of steel under hot deformation conditions with regard to the effects of dynamic recovery and dynamic recrystallization. For this purpose, Kocks-Mecking dislocation model together with a first order rate equation have been utilized. To associate temperature and strain rate variations on flow behavior of deforming metal, a thermo-viscoplastic finite element model has been coupled with the proposed model. To verify the modeling results, hot rolling experiments were performed and roll forces at various temperatures and rolling speeds were recorded. A good agreement was found between the predicted and the experimental data. © 2005... 

During power system restoration, it is necessary to check the phase angle between two buses before closing circuit breakers to connect a line between them. These angles may occur across a tie line between two systems or between two connected subsystems within a system. In case of large Standing Phase Angle (SPA) difference the synchrocheck relay does not allow closing of the breaker for this line. Therefore, this excessive SPA has to be reduced before attempting to connect the line. In this paper a new and fast method for reducing SPA is presented. For this purpose, the standing phase angle difference between two specific buses is represented in terms of sensitivity factors associated with... 

Distribution automation (DA) application for fault management in the electricity distribution networks is one of the main potential remedial actions to reduce customers' outage times and hence improve service reliability. As a result, various automation schemes have been developed and introduced in different countries and by different venders. The impacts of implementing a specific automation scheme on reliability indices of a given distribution system can be different from other available automation schemes. For this reason, when comparing the available automation schemes with each other or with the other reliability improvement measures, it is necessary to perform a course of reliability... 

Flow curves and microstructural changes of nanostructured Al6063 alloy produced by mechanical alloying followed by hot extrusion were investigated by means of uniaxial compression test in the temperature range between 300 and 450 °C and strain rate range between 10-2 and 1 s-1. The analysis of flow curves were performed by a hyperbolic sine law equation and the stress exponent and activation energy were determined to be 2.9 and 228 kJ mol-1, respectively. The microstructural constituents for elaboration of deformation mechanisms were observed by TEM and EBSD under FEG-SEM. The microstructural observations determine that dynamic recovery through the formation of subgrains within the grains... 

Frequency control during power system restoration has not been strongly addressed. Operators are often concerned with the offline sizing of load and generation steps, but, nowadays, the introduction of Wide Area Measurement System (WAMS) makes it possible to monitor the stability of power system online. The constraints of WAMS operation result in some changes in power system frequency control. This paper proposes a novel methodology for frequency control and monitoring during the early steps of power system restoration based on WAMS. Detailed load modeling is achieved based on the static load modeling approach. Power generators' modeling is also accomplished utilizing the single machine... 

Distribution automation (DA) application for fault management in the electricity distribution networks is one of the main potential remedial actions to reduce customers' outage times and hence improve service reliability. As a result, various automation schemes have been developed and introduced in different countries and by different venders. The impacts of implementing a specific automation scheme on reliability indices of a given distribution system can be different from other available automation schemes. For this reason, when comparing the available automation schemes with each other or with the other reliability improvement measures, it is necessary to perform a course of reliability... 

One of important subjects in power system restoration that already is not addressed is frequency control. Operators are often concerned with the size of load and generation, which can be safely increased. With the emphasis on higher utilization of power systems, monitoring of its dynamics is becoming increasingly important. This requires information with higher accuracy and update rates faster than those usually provided by traditional SCADA systems. In addition, it must be synchronized over a wider geographical area than that provided by traditional protection systems. Nowadays, the introduction of Phasor Measurement Units (PMU) and Wide Area Monitoring Systems (WAMS) as well as advances in... 

Implementation of Distribution Automation (DA) in electric power distribution systems can result in customer satisfaction with improved reliability, consistent quality and high-tech services. Loop Restoration Strategy (LRS) is a special DA method in the feeder level which is used by electric utilities to improve distribution system reliability. The effects of the implemented LRS on the reliability indices of a given distribution system mainly depend on its Automatic Control System (ACS). Selecting the type of ACS of LRS by electric utilities relies on the level of improvement required at load points and system oriented reliability indices. A step by step evaluation procedure is proposed in... 

This paper presents a distributed, robust, finite-time secondary control for both voltage and frequency restoration of an islanded microgrid with droop-controlled inverter-based distributed generators (DGs). The distributed cooperative secondary control is fully distributed (i.e., uses only the information of neighboring DGs that can communicate with one another through a sparse communication network). In contrast to existing distributed methods that require a detailed model of the system (such as line impedances, loads, other DG units parameters, and even the microgrid configuration, which are practically unknown), the proposed protocols are synthesized by considering the unmodeled... 

This paper presents a new method for restoration of distribution networks after a fault occurrence. This problem is solved from the viewpoint of the distribution system operator with the main goal of minimizing the operating cost during the fault clearance period. The effects of distributed generation (DG) units and direct load control (DLC) programs are considered in designing the proposed restoration procedure. Moreover, the uncertainties associated with the predicted loads of different nodes and the availability of DG are modeled here. Robust optimization is used to model the uncertainties of restoration problems and manage their associated risks. Finally, a robust reconfiguration plan is... 

High-voltage power supplies (HVPSs) are widely used to supply vacuum tubes. The amount of delivered energy from the HVPS to the tube is an important issue during the vacuum arc in the tube. The conventional protection mechanism consists of a shunt crowbar which diverts the fault current from the tube to itself as a parallel path. The crowbar circuit is usually built of the devices without the turn-off capability. It is a drawback since the output of the power supply is shortened for a long time. Thus, the restoration time of these power supplies is excessive. This demerit can have detrimental effects on mission-critical applications. In this paper, the insulated-gate bipolar transistor... 

The remediation of nonaqueous phase liquids (NAPLs) enhanced by surfactant and nanoparticles (NP) has been investigated in numerous studies. However, the role of NP-assisted surfactants in the dissolution process is still not well discussed. Besides, there is a lack of empirical dissolution models considering the effects of initial residual saturation Strap, NAPL distribution, and surfactant concentration in NAPL-aqueous phase systems. In this work, micromodel experiments are conducted to quantify mass transfer coefficients for different injected aqueous phases including deionized water, SDS surfactant solutions, and NP-assisted solutions with different levels of concentrations and flow... 

In recent decades, population growth, agricultural development and climate change have caused environmental problems in the world, especially in the arid and semi-arid regions such as Iran. Urmia Lake, one of the unique biosphere reserves of the world, has suffered from these problems in the last 20 years. Although many studies conducted to the negative impacts of human-induced activities, especially agricultural expansion on the lake, few studies focused on providing restoration plans for that. This study uses a system dynamics method for modelling the restorations scenarios of Urmia Lake based on the prey-predator approach. This method is helpful to simplify the complicated feedbacks and... 

Hot deformation behavior of Al6063 alloy produced by direct powder extrusion was studied by means of uniaxial compression test in the temperature range between 300 and 450°C and strain rate range between 0.01 and 1s -1. Electron backscatter diffraction (EBSD) technique and transmission electron microscopy (TEM) were utilized to study the microstructure of the material before and after the hot deformation. The microstructure of the extruded alloy consisted of elongated grains within a subgrain structure and small grains free of low angle grain boundaries (LAGBs). An equiaxed duplex microstructure consisting of large substructured grains and fine grains separated by high angle grain boundaries...