Sharif Digital Repository

The effects of liquid environment on nucleation, growth and aggregation of gold nanoparticles were studied. Gold nanoparticles were prepared by pulsed laser ablation in deionised water with various concentrations of ethanol and also in pure ethanol. UV/visible extinction and TEM observations were employed for characterization of optical properties and particle sizes respectively. Preparation in water results in smaller size, shorter wavelength of maximum extinction and stable solution with an average size of 6 nm. Nanoparticles in solution with low concentration ethanol up to 20 vol% are very similar to those prepared in water. In the mixture of deionised water and 40 up to 80 vol% ethanol,... 

In this research, the effects of preparation conditions, including the coagulation bath temperature, polymer solution composition, preliminary drying time, and thickness of cast polymeric films, on the morphology of ethylene/vinyl acetate copolymer membranes were investigated with scanning electron microscopy and nitrogen gas permeability tests. Flat sheet membranes were prepared through a thermal-wet phase-inversion method. Scanning electron microscopy pictures showed asymmetric structures for some of the membranes. It was also observed that the porosity of the membranes decreased with an increase in the temperature of the coagulation bath and the solvent evaporation period. When the... 

In this investigation, a neural network model was used to predict mechanical properties of dual phase (DP) steels and sensivity analysis was performed to investigate the importance of the effects of pre-strain, deformation temperature, volume fraction and morphology of martensite on room temperature mechanical behavior of these steels. In order to train the neural network, dual-phase (DP) steels with different morphology and volume fractions of martensite were deformed between 2 and 8%, at high temperature range of 150-450 °C. The results of this investigation show that there is a good agreement between experimental and predicted values and the well-trained neural network has a great... 

The effect of the nucleating agent masterbatch carrier resin on the nonisothermal crystallization of a pipe-grade polypropylene block copolymer was investigated at three different cooling rates using differential scanning calorimetry (DSC). Bis(3,4-dimethylibenzylidene) sorbitol (DMDBS), a well-known, third-generation sorbitol derivative, was used as a nucleating agent in this study. Crystallization kinetic parameters obtained from DSC cooling curves showed that incorporation of a nucleating agent by means of a masterbatch increased the crystallization rate by approximately two times compared to that of the sample with the same concentration of nucleating agent without the use of a... 

The present work studied bioactive coatings on the surface of ceramic biomaterials. Zirconia toughened alumina (ZTA) composites containing 15 mol.-%. Partially stabilised zirconia was prepared after 1 h sintering at 1550°C. Apatite layers were then coated onto the surfaces of composites by the biomimetic method using 1·5-2 multiply concentrations of simulated body fluid (SBF). Before treatment in SBFs, a sodium silicate layer was employed as nucleating agent to induce the formation of a calcium phosphate layer. The effect of immersion time on the morphology of the precipitate was monitored with a scanning electron microscope. X dot maps revealed that there is a relationship between... 

In this work, ultraviolet photodetectors based on electrodeposited ZnO sheet thin films were fabricated on a glass substrate. Before electrodeposition, a thin buffer layer of ZnO was deposited on the glass by pulsed laser deposition method. This layer not only acted as a nucleation site for ZnO sheet growth, but also made it possible to use cheap glass substrate instead of conventional fluorine-doped tin oxide (FTO) substrate. Our results showed that photoresponse properties of the photodetectors strongly depend on the sheet sizes. The smaller sheets exhibited enhanced photosensitivity, shortened fall times and decreased gain compared to larger ones. We showed that photodetectors based on... 

The most applications of gold nanoparticles are in the photo-electronical accessories and bio-chemical sensors. Chloride solution with cysteine additive was used as electrolyte in gold nanoparticles electrodeposition. The nucleation and growing mechanism were studied by electrochemical techniques such as cyclic voltammetry and chronoamperometry, in order to obtain a suitable nano structure. The deposition mechanism was determined as instantaneous nucleation and the dimension of particles was controlled in nanometric particle size range. Atomic Force Microscope was used to evaluate the effect of cysteine on the morphology and topography of gold nanoparticles. Finally the catalytic property of... 

The crystallization behavior of fluorphlogopite, a glass-ceramic in the MgO-SiO2-Al2O3-K2O-B 2O3-F system, was studied by substitution of Li 2O for K2O in the glass composition. DTA, XRD and SEM were used for the study of crystallization behavior, formed phases and microstructure of the resulting glass-ceramics. Crystallization kinetics of the glass was investigated under non-isothermal conditions, using the formal theory of transformations for heterogeneous nucleation. The crystallization results were analyzed, and both the activation energy of crystallization process as well as the crystallization mechanism were characterized. Calculated kinetic parameters indicated that the appropriate... 

Single-walled carbon nanotubes (SWCNTs) and multiwalled carbon nanotubes (MWCNTs) were synthesized in aqueous solutions containing FeCl2, FeCl3, FeSO4 and Fe2(SO4) 3. The effects of iron charge and the counter ions on the formation of carbon nanotubes (CNTs) were investigated. Thermogravimetric (TG) analysis indicated that carbon multilayer structures including CNTs and multishell graphite particles were formed in deionized (DI) water without the iron precursor. SWCNTs were also synthesized in the presence of the iron ions. It was also found that the mole ratio of [Fe2+]/[Fe3+] in the solution has a significant influence on the purity of CNTs and the process yield. The highest yield was... 

Abstract In this study, aluminium titanate (AT) particles and nanofibers were synthesized through citrate sol gel and sol gel-assisted electrospinning methods in both nanostructured powder and nanofiber forms. The results of X-ray diffraction analysis, field-emission scanning electron microscopy and differential thermal analysis showed that the synthetic products benefit a nanostructured nature with a grain size less than 70 nm. The optimal values for time and temperature at which a roughly pure AT is attained were determined as 2 h and 900 C, respectively. It was found that the sol gel precursor bears an amorphous structure till 700 C and begins to be crystallized to alumina, anatase and AT... 

Ultra fine CuO nanoparticles In the range of 2 ± 0.2 nm were synthesized by the supercritical hiydrotliermal method in a batch reactor. Itwas demonstrated that elevating the pH of the Cu2+ precursor solution to around 6 (neutral condition) not only does not lead to excessive agglomeration of the particles, but also reduces particle size and in general promotes their nanoscale characteristics. Prepared nanoparticles were immobilized in the biopolymcric matrix of barium alginate and calcined at different temperatures resulting in micro spherical granules of high porosity and elevated mechanical strength. The fabricated samples were characterized using x-ray diffractometry (XRD), transmission... 

One-dimensional (1D) MgO structures were successfully synthesized via carbothermic reduction of mechanically activated mixture of MgO and graphite. Mechanical activation of source materials before carbothermic reduction can substantially enhance the formation of MgO products at a temperature (1000 °C) relatively lower than that required in previous approaches (≥1200 °C). However, the morphology of MgO formed is dependent on the degree of mechanical activation and the condition of the subsequent carbothermic reduction. Two distinctive morphologies were found for MgO products synthesized using our method: single crystalline nanorods with rectangular cross-sections whose diameters range from 50... 

The objective of this study was to evaluate the effects of P 2O5 particle size distribution on the crystalline phases and microstructure of lithium disilicate glass-ceramics derived from the TiO2-ZrO2-Li2O-CaO-Al2O 3-SiO2 system for dentistry applications. The samples were made via fusion and casting procedure. Crystallisation as well as the morphology and microstructure of the samples were investigated using X-ray diffraction, differential scanning calorimetric and scanning electron microscopy. The results showed that the crystallisation of the samples occurred in the range of 500-650°C. The main crystalline phase was lithium disilicate (Li2Si2O5) along with Lithium metasilicate (Li2SiO3),... 

Boiling of water/triethyleneglycol (TEG) binary solution has a wide-ranging application in the gas processing engineering. Design, operation and optimization of the involved boilers require accurate prediction of boiling heat transfer coefficient between surface and solution. In this investigation, nucleate pool boiling heat transfer coefficient has been experimentally measured on a horizontal rod heater in water/TEG binary solutions in a wide range of concentrations and heat fluxes under ambient condition. The present experimental data are correlated using major existing correlations. In addition a correlation is presented for prediction of pool boiling heat transfer for the system in which... 

To investigate boiling heat transfer characteristics of nanofluids, transient quenching experiments of a high temperature silver sphere in water-based nanofluids with Ag and TiO2 nanoparticles were performed. A silver sphere with a diameter of 10 mm and an initial temperature of 700 °C was quenched in these nanofluids at a temperature of 90 °C. The results showed a considerable reduction in the quenching ability of nanofluids compared to that of pure water. The presence of nanoparticles in water caused the film boiling mode to vanish at lower temperatures depending on the mixture concentration. Calculated heat transfer rates in nanofluids were lower than those in pure water. In the quenching... 

Microstructure and mechanical properties of AA2024 after severe plastic deformation (SPD) and non-isothermal annealing were investigated. The non-isothermal treatment was carried out on the severely deformed AA2024, and the interaction between restoration and precipitation phenomena was investigated. Differential scanning calorimetry, hardness and shear punch tests illustrate that static recovery and dissolution of GPB zones/Cu–Mg co-clusters occur concurrently through non-isothermal annealing. Scanning electron microscope and electron backscatter diffraction illustrate that non-isothermal annealing of deformed AA2024 up to 250 °C promotes the particle-free regions and also particle... 

The boiling phenomena in a quiescent fluid is the nucleate pool boiling which has attracted much interest in the thermal management studies. This paper investigates the effect of the installed Twisted Tape Fins (TTFs) on the heat transfer from a surface with a temperature above the water saturation point to a coil condenser. Four different arrangements of TTFs (1, 3, 5, and 9 TTFs) are fabricated and their boiling performance in distilled water at atmospheric pressure is experimentally tested. It was observed that the increase in the boiling heat transfer coefficient of the plate with nine TTFs compared to that of the plain one is 15.5%. Furthermore, the effect of TTFs heights on the heat... 

The objective of this work was to study the influence of titanium on API 5L-X70 steel weld metal properties at manganese levels of 1.4 and 2%. The best mechanical properties in the weld series were obtained in two compositions, i.e. 1.92%Mn-0.02%Ti and 1.40%Mn-0.08%Ti. In both groups of welds, acicular ferrite in the microstructure was increased with addition of titanium in the range of 0.02-0.08%. Manganese helped to refine and homogenize weld microstructures. Increased hardenability of the weld due to further addition of titanium or manganese encouraged grain boundary nucleation of bainite with greater frequency than intragranular nucleation of acicular ferrite. Also, the amount of... 

The monosize formation, the ability of self-assembly, and high coercivity after annealing are the properties that lead to the priority of FePt magnetic nanoparticles for the application in recording media. These nanoparticles were synthesized by the superhydride method. The effect of oleic acid and oleylamin ligands on the fabrication of nanocrystals and the stability of the FePt system has been studied. TEM, EDS, XRD, and spectrophotometer analysis show the formation of FePt nanoparticles dispersion in hexane and indicate that oleylamine increases the number of particles in the nucleation stage and decreases the size of the Pt core, whereas the oleic acid controls the shell of the particle...