Sharif Digital Repository

Recent investigations on construction engineering have determined that repairing of Reinforced Concrete (RC) by means of fiber reinforced polymer (FRP) composites is an effective method of retrofitting existing columns. The main research in this thesis focuses on the repair of concrete specimens which are damaged and their initial strength has been reduced. To achieve this purpose, through experimental procedures, the effect of confining damaged concrete cylinders by FRP, has been investigated. The experimental program included three parameters: type of fibers (glass or carbon), type of confining (full or partial), and the number of layers. First concrete cylinders were made and loaded to... 

In this thesis, we aim to study the elastic-plastic behavior of short fiber reinforced composites experimentally and analytically. The experimental investigation is applied to glass fiber-polypropylene composites (PP/GF). The samples are produced by injection process with maximum temperature of 190C. Fibers are randomly oriented in this procedure of fabrication. The samples are tested in tension, and the mechanical strength is measured by changes in fiber content. The Young's modulus is also investigated in these experiments.Also in this thesis, an analytical model for calculation of Young’s modulus of fiber reinforced composite materials is proposed. In this analysis a displacement field is... 

This study inspects the flexural response of RC beams at the presence of compressive GFRP bars as well as tensile bars. Total of 9 reinforced beams were investigated. Three values of tensile reinforcement percentage were considered. For each tensile reinforcement value, three types of compressive reinforcement were taken into account which are classified into zero compressive bars, less than tensile reinforcement value and similar to tensile reinforcement value. The concrete was used in this study is C45 and as a constant parameter.Specimens were tested with four-point bending method using the actuator equipped at the strong floor laboratory to attain maximum flexural strength and... 

During all operations in oil and gas reservoirs, it is possible to cause formation damage. These damages can greatly reduce the rate of production. One of the major damages that can seriously affect the performance of a reservoir is the damage caused by drilling fluid. The main purpose of this thesis is to study the main mechanisms of formation damage caused by water-based drilling fluid using a glass micromodel for the first time. An accurate understanding of the mechanisms of formation damage can provide a good understanding of the selection of the type and concentration of materials used, as well as appropriate methods to control and eliminate damages. for controlling the drilling fluid... 

Aseptic loosening and infection are two major problems of bone implants. Aseptic loosening occurs due to poor cell growth and poor adhesion to the implant surface over time. Bone infection at the implant site occurs mainly by the staphylococcus aureus bacteria. In some cases, infection occurs in the short term and in the early times after implantation, and in some cases, infection occurs in later times. The aim of this study is to synthesize and evaluate antibacterial coatings, while having cell growth-promoting components and cell differentiation to solve bone implant problems simultaneously. Also, the issue of bacterial resistance to antibiotics and their risks in bone implants is another... 

In this research, we studied the effect of compatibilizer and short glass fiber on microstructure and mechanical properties of PBT/PC blends. Fisrt, Antioxidants and sodium pyrophosphate dibasic were used to suppress transesterification in PBT/PC Blend. The results showed that best composition occur when both of them are used. In the next step, we used 3%wt MBS (methyl methacrylate-butadiene-styrene) and saw that this weight percent of this compatibilizer doesn’t useful. Moreover addition of short glass fiber to PBT/PC was examined and the results showed that mechanical properties of composite are extensively increased. Also in this step, we proved this idea that we can replace some of PBT... 

In this research, Mg-Zn bulk metallic glasses have been investigated using molecular dynamics simulation. In order to study the structure of this alloy, coordination number, short and medium order of chemical range, Voronoi analysis, glass conversion temperature and atomic pair distribution function have been used. According to the results, the full icosahedral structure with IS connection type in comparison with other structures has an essential role in the stability of the system during cooling and creating medium-scale areas. The results show that the ability to form glass depends on the chemical composition and cooling rate. In this research, the cooling rate is considered to be 1011 K/s... 

bulk metallic glass Unlike metal materials that have a crystalline structure, amorphous glass is an amorphous material with an irregular atomic structure that simultaneously has the same physical properties as metals. Due to the absence of crystal defects such as dislocation and grain boundaries, these materials show unique mechanical properties such as high strength and elastic strain, abrasion resistance and proper corrosion. However, their plastic deformation is heterogeneous, concentrated, and accompanied by sudden failure. Unlike metals, these materials do not have a long-range crystalline order, and their atomic structure includes short-range and mid-range order. The short-range order... 

In recent years, desulfurization has received much attention due to its devastating environmental effects. The existence of sulfur compounds has effects such as corrosion, poisoning of catalysts, reduction of heat of combustion and reduction of price. Sulfur compounds in hydrocarbon fuels also produce sulfur oxides caused by combustion then they enter the atmosphere, and cause acid rain. Acid rain dissolves building materials, poisons lakes, and destroys forests. Therefore, removing sulfur or converting it to less harmful substances is one of the most important processes in refineries. The method studied in this research is the use of adsorption desulfurization method by microchannel which... 

Currently, using biocompatible and injectable polymeric microcarriers as one of the efficient methods to transfer cells and active agents has gained much attention for bone regenerative medicine. However, they have some drawbacks such as weak mechanical stability and lack of mineral materials, which are the major ingredients of the bone tissues. Accordingly, it is expected that mimicking the chemical and physical structure of bone tissues could be valuable in their medical applications. Herein, a new porous biodegradable microcarriers (MCs) made of silk fibroin-oxidized alginate-bioactive glass was fabricated by electrospraying method. Response surface methodology (RSM) was used to study the... 

Formation damage in petroleum engineering is an important and fundamental phenomenon. During drilling operation, penetration of either the solid phase of drilling fluid or the base-fluid into the porous medium, reduces the permeability of the formation. While most experiments in the literature have focused on core-scale and beyond, there is lack of pore-scale studies. Moreover, presence of fractures has an undeniable effect on the extent of formation damage. Thus, the main objective of this dissertation is to investigate the effects of fractures on the severity of formation damage caused by the water-based drilling fluid and the mechanisms of formation damage at the pore scale, using glass... 

FRP rebars due to various properties such as high resistance to weight ratio, high corrosion resistance, high tensile strength, low weight, resistance to electrical and magnetic conductivity, and other desirable properties, have always been an interesting topic for researchers as an alternative to steel rebars in special conditions.In this research, a two-dimensional sway intermediate concrete frame with three stories and two bays reinforced with GFRP bars was designed and studied. Unlike previous researches and design codes, the compressive strength of the bars was considered in the design process. With computer coding in Matlab software, column interaction diagrams and a special contour... 

The following dissertation discusses Ionic Liquids (ILs) as an alternative to commercial surfactants for use in the Enhanced Oil Recovery process. Ionic Liquids came to researchers’ attention due to their environmental nature and their tolerance for high temperatures and salinity. In this work, firstly, an extensive literature review is carried out, and then, experiments are designed and performed to evaluate ILs’ surface activity and performance in a lab-scale EOR set-up. The Ionic Liquids used in this work consist of three types of methylimidazolium nitrate, [MIM]+[NO3]-, with three different alkyl chain lengths. This combination, and specifically the effect of nitrate anions on EOR and... 

The consumption of plastics in the world is increasing and this is accompanied by the challenges of production from oil products and carbon footprint, waste production and environmental issues. The solutions to these challenges are material recycling and the production of biocompatible plastics. Polypropylene is a widely used polymer that is commonly used in conjunction with reinforcements such as fiberglass. Natural fibers can be substituted to increase the biocompatibility of the composite, which, despite its many advantages, presents challenges. The most important challenge is the poor adhesion of the fibers and the matrix due to the hydrophilicity of natural fibers and hydrophobicity of... 

Despite extensive studies on the behavior of reinforced concrete slabs, especially those reinforced with steel rebars, no comprehensive studies have been conducted on the behavior of concrete slabs reinforced with FRP rebars. Therefore, there are some ambiguities regarding the tensile and compressive behavior of these rebars in the load-bearing capacity of reinforced concrete slabs (depending on their amount in the slab and their combination with steel rebars). Hence, in this study, in order to ensure the accuracy of numerical simulations, the numerical 3D simulation of a one-way concrete slab reinforced with tensile FRP rebars was performed using the finite element Abaqus software.... 

The rehabilitation of old structures holds a lot of importance, as many structures with a life span of over 30 years are prone to severe damage and even collapse. To overcome this problem, the use of FRP sheets to strengthen structures is suggested. RC-arches have been used in many structures such as bridges and require specific consideration in terms of strengthening. So far, the influence of the number of FRP layers and location, the height of arch and percentage of reinforcement on strengthened arch behavior have not been investigated. In this research, reinforced concrete arch members strengthened with GFRP and CFRP were investigated. A total of 28 Specimens, including four... 

As nuclear energy continues to be used as a useful energy resource, waste management, especially management of high-level nuclear waste (HLW), will always be a major concern, as the future generations should not be deprived of the valuable benefits of this energy. Vitrification of liquid high-level radioactive waste (HLW) has received greater attention, worldwide, than any other high-level waste solidification process. The high solubility of HLW in borosilicate glass, the controllable temperature of this type of glass and its low leaching rate in repository environment, have introduced borosilicate glass as a suitable host for HLW immobilization. In this project, the immobilization of the... 

Based on numerous laboratory and field evidence, low-salinity waterflooding or engineered salinity waterflooding can lead to enhanced oil production. According to the literature, the mechanisms involved in this process can be divided into two general categories: fluid-fluid interactions and solid-liquid interactions. These mechanisms are caused by intermolecular and electrostatic forces at the rock and fluid interfaces. The most important controlling factor of the electrostatic forces is the concentration of ions at/near fluids-rock interface. Therefore, improving the concentration of ions causes a shift in wettability toward a more water-wetting state, eventually leading to increased oil... 

Understanding biological systems requires extensive knowledge of individual parameters, and to study the processes of cell differentiation and cell behavior, a suitable environment must be created with the physiological conditions of the human body. For this purpose, with the knowledge of microfluidics, a microenvironment can be provided to study the behavior of cells on a small scale. The use of bone tissue model microfluidic chips is an alternative and new method in which it is possible to study the behavior of cells to differentiate into bone and to examine the toxicity of drugs, which in itself can help in the effective and successful treatment of these cases show. Therefore, in this... 

Nowadays, with the increasing number of polyethylene terephthalate wastes, the issue of its recycling has become very important. Among the problems of polyethylene terephthalate recycling are its loss of crystallinity and mechanical properties. Recycled polyethylene terephthalate does not have the properties of new polyethylene terephthalate and using its mixture with other materials is an effective way to remove its waste from nature and return it to the production cycle. The aim of this study is to produce a mixture of recycled polyethylene terephthalate with polycarbonate and glass fibers with mechanical properties such as good impact strength, which ultimately leads to the production of...