Sharif Digital Repository

A simple, efficient, and general method has been developed for the conversion of aldehydes to 1,1-diacetates with the use of acetic anhydride and solid LiClO4 under first solvent-free and mild conditions in good yields. This method applies to not only simple but also to conjugated aldehydes. © 2005 Elsevier B.V. All rights reserved  

The geometry structures of hexa-coordinated [NiLX]X complexes (X = Cl -, Br-, I-) {L = 8,9,18,19-tetrahydro-7H,17H- dibenzo[f,o] [1,5,9,13]dioxadiaza cyclohexadecine-8,18-diol} are optimized by density functional theory (DFT) using B3LYP/LANL2DZ. The calculated geometric parameters are in good agreement with the corresponding experimental values. Calculation results about these complexes show that dipole moment decreases, and the energy levels of HOMOs descend from iodo-complex to chloro-complex. The energy levels of HOMOs descend gently from iodo-complex to chloro-complex, while the energy levels of LUMOs in the present complexes are almost similar; therefore the energy gapes between HOMOs... 

Alumina nanofluids are one of the most useful nanofluids. In order to evaluate the colloidal behavior of nanoparticles in alumina/water nanofluid, the influence of effective factors such as pH, ionic strength and surfactants, was studied. Zeta potential, particle size and turbidity change of each nanofluid was investigated. According to the results for 0.05, 0.1 and 0.2 mass% nanofluid, point of zero charge was obtained at pH values of 9.5, 10.2 and 10.5, respectively. The highest nanofluid stability occurred at pH 4 and its lowest was at pH 10. The anionic surfactant had a greater effect on the stability in compared with cationic and nonionic surfactants. By increasing in ionic strength,... 

Alumina nanofluids are one of the most useful nanofluids. In order to evaluate the colloidal behavior of nanoparticles in alumina/water nanofluid, the influence of effective factors such as pH, ionic strength and surfactants, was studied. Zeta potential, particle size and turbidity change of each nanofluid was investigated. According to the results for 0.05, 0.1 and 0.2 mass% nanofluid, point of zero charge was obtained at pH values of 9.5, 10.2 and 10.5, respectively. The highest nanofluid stability occurred at pH 4 and its lowest was at pH 10. The anionic surfactant had a greater effect on the stability in compared with cationic and nonionic surfactants. By increasing in ionic strength,... 

The need for the control of Volatile Organic Compounds (VOCs) has led engineers to modify wastewater aeration tank systems. In this research, air recirculation has been investigated as a possible VOC control strategy for these systems. A steady-state mathematical model of VOC emission rates has been developed from the fundamentals of VOC convection, volatilization and biodegradation. This model has been used to study the effect of aeration recirculation in enhancing the biodegradation of VOCs in the system, using dichloromethane as a typical VOC. A feasibility study considering plants of various sizes is needed to compare the costs and benefits of air recirculation to other VOC control... 

We introduce highly antifouling Polymer-Nanoparticle-Nanoparticle/Polymer (PNNP) hybrid membranes as multi-functional materials for versatile purification of wastewater. Nitrogen-rich polyethylenimine (PEI)-functionalized halloysite nanotube (HNT-SiO2-PEI) nanoparticles were developed and embedded in polyvinyl chloride (PVC) membranes for protein and dye filtration. Bulk and surface characteristics of the resulting HNT-SiO2-PEI nanocomposites were determined using Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA). Moreover, microstructure and... 

Abstract: In this investigation, monodisperse CuGaS2 nanoparticles intended for use as visible-light-absorbing materials were synthesized using a facile one-step heating method that involved dissolving the precursors copper chloride, gallium acetylacetonate, and thiourea in a solvent consisting of either oleylamine alone or a combination of oleylamine, oleic acid, and 1-octadecene. The shapes of the resulting nanoparticles were either elongated, polygonal, or a mixture of both, depending on whether the crystal structure of the nanoparticles was predominantly wurtzite, predominantly chalcopyrite, or a more balanced mixture of both wurtzite and chalcopyrite (i.e., the nanoparticles were... 

The Zr-based metal-organic framework (MOF, UiO-66) was synthesized solvothermally. The synthesized UiO-66 was activated using different solvents (acetone, chloroform, and ethanol) via two activation methods of centrifugation and Soxhlet extraction over different periods (1–10 days). The crystalline structure and morphology of the synthesized UiO-66s were characterized by X-ray diffraction (XRD), nitrogen adsorption-desorption, and field-emission scanning electron microscopy (FESEM) techniques. The adsorption behaviors of the synthesized UiO-66s were then investigated by selecting anionic methyl red (MR) and cationic methylene blue (MB) as the model dyes. It was found that a change in... 

The Zr-based metal-organic framework (MOF, UiO-66) was synthesized solvothermally. The synthesized UiO-66 was activated using different solvents (acetone, chloroform, and ethanol) via two activation methods of centrifugation and Soxhlet extraction over different periods (1–10 days). The crystalline structure and morphology of the synthesized UiO-66s were characterized by X-ray diffraction (XRD), nitrogen adsorption-desorption, and field-emission scanning electron microscopy (FESEM) techniques. The adsorption behaviors of the synthesized UiO-66s were then investigated by selecting anionic methyl red (MR) and cationic methylene blue (MB) as the model dyes. It was found that a change in... 

FAPbI3 perovskites are excellent candidates for fabrication of perovskite solar cells (PSCs) with high efficiency and stability. However, these perovskites exhibit phase instability problem at room temperature. In this work, to address this challenge we use methylammonium chloride (MACl) as an additive and employed a layer-by-layer thermal evaporation technique to fabricate high-quality perovskite films on a large scale of 25 cm2. The optimized perovskite films show high crystallinity with large grains in the μm-range and reveals phase stability due to the presence of MACl after the annealing process. Finally, we achieved PSCs with 17.7% and 15.9% for active areas of 0.1 cm2 and 0.8 cm2,... 

Lightweight geopolymer concretes have gained attention because of their superior durability, lower environmental impact and sustainable characteristics. They are the product of natural or artificial aggregates with low specific gravities mixed with aluminosilicate binders, and an alkaline solution. In this study, different aspects of lightweight geopolymer concretes and mortars such as environmental and economic considerations, materials and mixture, durability-related properties like permeability, chloride attacks and performance at high temperatures, thermal conductivity, and the microstructure are reviewed. This study also discusses the effect of different geopolymer binders and various... 

Ag and Ni are immiscible, mainly due to their large lattice mismatch. This paper reports on their nanoscale formation of solid solution at room temperature by simple reduction reactions which lead to the amorphous Ag-Ni alloy nanoparticles (ANPs) with mono-disperse distribution. Microscopic and spectroscopic studies confirmed dependence of the alloy composition on size of nanoparticles. In the presence of different ligands such as sodium citrate, polyvinyl alcohol and potassium carbonate a mixture of silver oxide and Ag-Ni ANPs was achieved. Stoichiometry of the Ag-Ni ANPs was also found to be strongly dependent on ligands of the reduction reaction and further study shows without any ligand... 

The effect of pulse reverse current (PRC) method on Ni-Mo coatings electroplated from chloride solution was investigated by various plating parameters such as plating duration, the anodic duty cycle, the anodic current density and the cathodic current density. By increasing the anodic duty cycle and anodic current density, the Mo content of coatings reached 68wt.% and 78wt.%, respectively at cathodic current densities of 500 and 300mAcm-2. The Mo content of coatings increases by the preferential dissolution of Ni on the anodic pulse and also by the replenishment of Mo complexes in the diffusion layer near the substrate surface during the anodic pulse. In comparison with the direct current... 

Until now, many algorithms have been introduced for finding arbitrary shaped clusters, but none of these algorithms is able to identify all sorts of cluster shapes and structures that are encountered in practice. Furthermore, the time complexity of the existing algorithms is usually high and applying them on large dataseis is time-consuming. In this paper, a novel fast clustering algorithm is proposed. This algorithm distinguishes clusters of different shapes using a twostage clustering approach. In the first stage, the data points are grouped into a relatively large number of fuzzy ellipsoidal sub-clusters. Then, connections between sub-clusters are established according to the Bhatiacharya... 

One of the most famous approaches for the segmentation of color images is finding clusters in the color space. Shapes of these clusters are often complex and the time complexity of the existing algorithms for finding clusters of different shapes is usually high. In this paper, a novel clustering algorithm is proposed and used for the image segmentation purpose. This algorithm distinguishes clusters of different shapes using a two-stage clustering approach in a reasonable time. In the first stage, the mean-shift clustering algorithm is used and the data points are grouped into some sub-clusters. In the second stage, connections between sub-clusters are established according to a dissimilarity... 

A novel sulfoxide containing bis(ether amine) monomer, 2,2'-sulfoxide- bis[4-methyl(2-trifluoromethyl)4-aminophenoxy) phenyl ether] (M2), was synthesized from the halogen displacement of 2-chloro-5-nitrobenzotrifluoride with dibenzosulfoxide (DH) in the presence of potassium carbonate, followed by catalytic reduction of bis(ether nitro) intermediate with Zinc/Ammonium chloride. A series of organic-soluble poly(ether amide)s (PA1-7) bearing sulfoxide and electronwithdrawing trifiuoromethyl group were synthesized from bis(ether amine) with various aromatic diacids (1-7) via a direct polycondensation with triphenyl phosphite and pyridine. The resulting polymers had inherent viscosities ranging... 

The formation of multi-walled carbon nanotubes (MWCNTs) during arc discharge in aqueous solutions of Fe2(SO4)3 and FeCl3 was studied. The concentration of iron ions changed from zero (deionized water) to 0.25 M and the cathodic products were examined by transmission electron microscopy, Raman spectrometry, and thermal gravimetric analysis. The experimental results showed that the crystallinity of MWCNTs is improved by increasing the concentration of iron ions. Nevertheless, the process yield and overall quality of the produced CNTs were significantly affected by iron concentration in the aqueous solution. This observation suggested that there should be an optimum iron concentration at which... 

In this study, the corrosion behaviour of Ni-Co alloys with low Co content, electroplated on steel substrate in sulphate bath, was investigated. The morphology of coatings was studied by optical and SEM microscopy. The corrosion products were analyzed using EDX. The results showed that Ni-1%Co coatings had a better corrosion resistance 0.30, 0.92 and 3.75 mpy for atmospheric, salt spray and polarization tests, respectively. These are 0.41, 1.20 and 5.40 mpy for pure nickel coatings that indicate the least corrosion resistance. Surface analysis revealed the presence of oxides, sulphides and chlorides in corrosion products  

In this paper, the hydrodynamic behaviour of the chemical reaction system (selenium, tellurium, and TBP) was interpreted in the Oldshue-Rushton extraction column. The optimum operating parameters for extracting the selenium and tellurium from chloride medium were carried out by using the batch experiments. The feed acidity of 5 molar and solvent phase with 20% (v/v) TBP in kerosene were optimised to examine the hydrodynamic parameters of the mentioned column. The impacts of operating variables such as rotor speed, inlet aqueous phase velocity, and inlet solvent phase velocity on the dispersed phase hold-up, mean drop size, slip velocity, drop size distribution, and extraction rate were... 

An experimental and modeling study on the feasibility of the Scheibel extraction column is presented for heavy metal separation from chloride solution. In continuous experiments, the chemical reaction systems are considered zinc extraction by D2EHPA and stripping from the loaded organic phase by chloride solutions. The experimental results represent that the best extraction and stripping rates in the agitation speed of 155 rpm and the rate of inlet phases of 28 L/h are equal to 99.56% and 98.11%, respectively. The mass transfer modeling by applying the forward mixing is interpreted for solvent extraction systems in this column with the fitting technique. The calculated results from...