Sharif Digital Repository

This study investigated the mode I fracture behavior of double cantilever beam (DCB) epoxy adhesive joints with similar adherends on the both sides (i.e., aluminum-aluminum or copper-copper) at different strain rates; i.e., quasi-static (∼10−3 s−1), low (∼7 s−1) and intermediate (∼14 s−1) rates. The fracture energy of the DCB joint in Al-adhesive-Al specimens decreased (i.e., by ∼62%, p = 0.0013) with an increase in the applied strain rate from quasi-static to low values, while it remained almost unchanged with further increase of stain rate to intermediate range (p > 0.05). For Cu-adhesive-Cu cases, however, the fracture energy was found to be almost insensitive to the applied strain rate... 

Recently, decellularized amniotic membrane-derived hydrogels (DAMHs) have received significant attention for wound care, ocular surface reconstruction, and chondral healing. Despite the advantages of DAMHs for tissue engineering (TE), the loss of structural components during the decellularization process mitigates their mechanical strength and thus limits their practical application. Herein, we present a method for the surface modification of two-dimensional nanosilicates (laponite) as a rheological modifier to tailor the properties of DAMHs. Results show that after introducing nanosilicates, severe aggregation of the nanoparticles occurs, owing to the shielding effect of ions on the surface... 

Tissue adhesives have been widely used for preventing wound leaks, sever bleeding, as well as for enhancing drug delivery and biosensing. However, only a few among suggested platforms cover the circumstances required for high-adhesion strength and biocompatibility, without toxicity. Antibacterial properties, controllable degradation, encapsulation capacity, detectability by image-guided procedures and affordable price are also centered to on-demand tissue adhesives. Herein we overview the history of tissue adhesives, different types of polysaccharide-based tissue adhesives, their mechanism of gluing, and different applications of polysaccharide-based tissue adhesives. We also highlight the... 

The tribological behaviors of an AISI 4340 ferritic-bainitic dual-phase steel with different bainite (VB) content were investigated. The effects of VB on wear resistance and the corresponding wear mechanisms were investigated using a pin-on-disk wear testing machine, at normal loads of 10 and 50 N, at a constant sliding velocity. The tensile and hardness tests showed that the yield strength, ultimate tensile strength, and hardness increased with increasing the VB. The wear test results at the 10 N normal load showed a direct correlation between the tensile and tribological behavior of the samples. Nevertheless, at the normal load of 50 N, unexpected behavior was observed due to the carbon... 

Breast cancer is the most prevalent type of cancer in women; hence, many researches have been focused on developing effective treatment protocols. In this study, a novel nanocarrier was fabricated for gene and photothermal combination cancer therapy by conjugating histone methyltransferase complex subunit SET1 (hSET1) on reduced polydopamine coated graphene oxide nanosheets (rGO-PDA). The rGO-PDA nanocarriers provide higher near-infrared absorption and further integrating with hSET1 antisense as an anticancer gene that down-regulates the amount of hSET1 overexpressed and suppresses the proliferation of cancer cells. The nanoplatform was prepared by polymerizing of dopamine, a mussel adhesive... 

Myocardial infarction is a major cause of death worldwide and remains a social and healthcare burden. Injectable hydrogels with the ability to locally deliver drugs or cells to the damaged area can revolutionize the treatment of heart diseases. Herein, we formulate a thermo-responsive and injectable hydrogel based on conjugated chitosan/poloxamers for cardiac repair. To tailor the mechanical properties and electrical signal transmission, gold nanoparticles (AuNPs) with an average diameter of 50 nm were physically bonded to oxidized bacterial nanocellulose fibers (OBC) and added to the thermosensitive hydrogel at the ratio of 1% w/v. The prepared hydrogels have a porous structure with open... 

Polylactic acid (PLA) scaffolds produced by the fused deposition modeling (FDM) method have biocompatibility, close Young's modulus to that of bone, and the ability to make complex shapes. However, PLA has some drawbacks like brittleness, inappropriate mechanical strength and hydrophobicity, and a low degradation rate. In this study, polyethylene glycol (PEG) (5 and 10 wt%) by solving method and titanium (Ti) particles (5 wt%) by two different methods were mixed with PLA to address the mentioned problems. Extruded filaments were investigated by X-ray diffraction (XRD), differential scanning calorimetry (DSC), and fourier transform infrared (FTIR). Surface morphology of the produced filaments... 

Targeted drug delivery methods have shown a significant impact on enhancing drug delivery efficiency and reducing drug side effects. While various stimuli have been used to promote the drug delivery process, applying ultrasound (US) waves to control drug particles through the human body, noninvasively, has drawn the scientist's attention. However, microcarriers delivery reaches the aneurysmal artery by US waves that exert volumetric forces on blood, and drug carriers, which can therefore affect blood flow patterns and movement pathways of drug carriers, have not yet been studied. In this study, we developed a 3-D patient-specific model of abdominal aortic aneurysm (AAA) to evaluate the... 

Cancer has long been a leading cause of death. The primary tumor, however, is not the main cause of death in more than 90% of cases. It is the complex process of metastasis that makes cancer deadly. The invasion metastasis cascade is the multi-step biological process of cancer cell dissemination to distant organ sites and adaptation to the new microenvironment site. Unraveling the metastasis process can provide great insight into cancer death prevention or even treatment. Microfluidics is a promising platform, that provides a wide range of applications in metastasis-related investigations. Cell culture microfluidic technologies for in vitro modeling of cancer tissues with fluid flow and the... 

Atherosclerotic plaques and thrombosis are chronic inflammatory complications and the main manifestations of cardiovascular diseases (CVD), the leading cause of death globally. Achieving non/minimal-invasive therapeutic means for these implications in the coronary network is vital and has become an interdisciplinary concern. Accordingly, smart drug delivery systems, specifically based on micro- and nanoparticles, as a promising method to offer non/minimal-invasive therapeutic mechanisms are under active research. Notably, computational models enable us to study, design, and predict treatment strategies based on smart drug delivery systems with less time and cost compared with conventional... 

Targeted drug delivery (TDD) to abdominal aortic aneurysm (AAA) using a controlled and efficient approach has recently been a significant challenge. In this study, by using magnetic microbubbles (MMBs) under a magnetic field, we investigated the MMBs performance in TDD to AAA based on the amount of surface density of MMBs (SDMM) adhered to the AAA lumen. The results showed that among the types of MMBs studied in the presence of the magnetic field, micromarkers are the best type of microbubble with a −50 % increase in SDMM adhered to the critical area of AAA. The results show that applying a magnetic field causes the amount of SDMM adhered to the whole area of AAA to increase −1.54 times... 

Due to their potential to recover strength and stiffness with a minimum impact on aerodynamic performance of a damaged structure, scarf repairs are boosted as a viable repair option for primary aero-structures. So far, most of the experimental and numerical studies have been limited to joint specimens and their equivalent 2 Dimensional models and a few number of studies attempted to examine the results using real scarf repair geometry. Suggestions previously made to justify the difference between scarf joint and scarf repair strength and possible solution to diminish the difference are challenged in current work. Here, it is tried to investigate the strengths and shortcomings of 2D scarf... 

Abstract: Commercially pure titanium and titanium alloys have been among the most commonly used materials for biomedical applications since the 1950s. Due to the excellent mechanical tribological properties, corrosion resistance, biocompatibility, and antibacterial properties of titanium, it is getting much attention as a biomaterial for implants. Furthermore, titanium promotes osseointegration without any additional adhesives by physically bonding with the living bone at the implant site. These properties are crucial for producing high-strength metallic alloys for biomedical applications. Titanium alloys are manufactured into the three types of α, β, and α + β. The scientific and clinical... 

The most common reasons for hard-tissue implant failure are structural loosening and prosthetic infections. Hence, in this study, to overcome the first problem, different bioinspired coatings, including dual acid-etched, anodic TiO2 nanotubes array, anodic hierarchical titanium oxide (HO), micro- and nanostructured hydroxyapatite (HA) layers, and HA/chitosan (HA/CS) nanocomposite, were applied to the titanium alloy surfaces. X-ray diffraction and FTIR analysis demonstrated that the in situ HA/CS nanocomposite formed successfully. The MTT assay showed that all samples had excellent cell viability, with cell proliferation rates ranging from 120% to 150% after 10 days. The HO coating... 

Surfaces with special wettability have aroused lots of attention due to their broad applications in many fields. In this work, we systematically report selective and various fabrications of nanofluids based on readily available materials such as SiO2 nanoparticles and polydimethylsiloxane to create superhydrophobic, superoleophobic, superhydrophilic/superoleophobic, and underwater superoleophobic coatings. The efficiency of prepared coatings is investigated on mineral rock plates as porous substrates via the straightforward and cost-effective solution-immersion technique. The static water contact angle of 170°, effortless bouncing of water droplets, and self-cleaning property with a near... 

Nature-inspired coating with polydopamine (PDA) is a promising way to improve the performance of graphene oxide (GO) based nanocomposites due to its high ability to enhance interactions in matrix-disperse systems. Here, we examined the capability of two types of PDA to develop the reinforced polyvinyl alcohol (PVA)/GO hydrogels. In the first mode, dopamine hydrochloride was polymerized as nanoparticles and then incorporated into PVA solution with GO nanoplatelets (P-NG hydrogel). In the second mode, polydopamine was polymerized in the presence of GO nanoparticles to obtain PDA surface-modified GO and then PVA nanocomposite hydrogel (P-CG sample). Rheological and tensile findings revealed... 

Fabrication of scaffolds with enhanced mechanical properties and desirable cellular compatibility is critical for numerous tissue engineering applications. This study was aimed at fabrication and characterization of a nanofiber skin substitute composed of collagen (Col)/sodium alginate (SA)/ polyethylene oxide (PEO)/Rhodotorula mucilaginosa sp. GUMS16 produced exopolysaccharides (EPS) were prepared using the biaxial electrospinning technique. This study used collagen extracted from the bovine tendon as a natural scaffold, sodium alginate as an absorber of excess wound fluids, and GUMS16 produced exopolysaccharides as an antioxidant. Collagen was characterized using FTIR and EDS analyses. The... 

Timber is widely used as a construction material; however, the environmental deterioration of timber is a crucial problem for the construction industry. Fiber-reinforced polymer (FRP) has been considered appropriate and beneficial for the repair and rehabilitation of timber. This study proposes three empirical models using a supervised machine learning method called gene expression programming (GEP) to predict the bond strength between timber and FRP under various environmental conditions. The first empirical model is used to predict bond strength under standard conditions. The two other models are proposed to predict the strength reduction in acidic and alkali solutions. The formulation... 

In this study, a numerical study on failure assessment and stress distribution on the adhesive region in a composite T-joint under bending load case is investigated using cohesive zone method (CZM). The Finite Element Model (FEM) has been verified with experimental results. To study the load transfer capability of the T-joint, five different adhesives are considered in the adhesive region and the effect of geometrical parameters such as stringer thickness, corner radius, and adherend thickness as well as micromechanical properties of reinforced fiber composite adherends are investigated. Effective properties of two composite adherends including Carbon-Epoxy (IM7/8552) and Glass-Epoxy... 

Targeted drug delivery using nanocarriers (NCs) is one of the novel techniques that has recently been used to improve drug delivery to the Abdominal aortic aneurysm (AAA) disease. The purpose of this study is to evaluate the surface density of NCs (SDNC) adhered via ligand-receptor binding to the inner wall of AAA. For this purpose, fluid–structure interaction (FSI) analysis was first performed for the patient-specific and ideal AAA models. Then, by injecting NCs into the aortic artery, the values of SDNC adhered to and interacted with AAA wall were obtained. Two types of NCs, liposomes, and solid particles in four different diameters, were used to investigate the effect of the diameter and...