Sharif Digital Repository

A numerical model for the deposition of silicon nitride using silane and ammonia mixture in a radio frequency plasma reactor has been developed. Plasma enhanced chemical vapor deposition process is simulated by combined analysis for the glow discharge, fluid flow and chemical reactions. The main goal is to investigate the effect of variations of the process parameters on the deposition rate, and uniformity of the resulting layer. The approach used is based on the theoretical partial differential equation models, without any empirical approximation of the critical data being used. Owing to the fact that the relevant equations are highly nonlinear, the discretization method is of great... 

Steam/water stratified flow would occur in transient condition (e.g. LOCA) in light water Nuclear Power Plants (NPPs). Due to high gradient of flow characteristics at the interface of steam/water flow, the prediction of flow characteristics (e.g. temperature, pressure, velocity, and Turbulent Kinetic Energy (TKE)) requires further attention and special interfacial models. Also, accurate simulation of these mentioned characteristics needs fine spatial mesh and very small time steps based on Computational Fluid Dynamics (CFD) standard criteria. In order to reduce the computational cost, the combination of thermal–hydraulic modelling and soft computing is considered as a new strategy in this... 

The aim of this study was to determine whether specific three-dimensional aortic shape features, extracted via statistical shape analysis (SSA), correlate with the development of thoracic ascending aortic dissection (TAAD) risk and associated aortic hemodynamics. Thirty-one patients followed prospectively with ascending thoracic aortic aneurysm (ATAA), who either did (12 patients) or did not (19 patients) develop TAAD, were included in the study, with aortic arch geometries extracted from computed tomographic angiography (CTA) imaging. Arch geometries were analyzed with SSA, and unsupervised and supervised (linked to dissection outcome) shape features were extracted with principal component... 

Radon is released from soil and building materials and can accumulate in residential buildings. Breathing radon and radon progeny for extended periods hazardous to health and can lead to lung cancer. Indoor air conditions and ventilation systems strongly influence indoor radon concentrations. This paper focuses on effects of air change rate, indoor temperature and relative humidity on indoor radon concentrations in a one family detached house in Stockholm, Sweden.In this study a heat recovery ventilation system unit was used to control the ventilation rate and a continuous radon monitor (CRM) was used to measure radon levels. FLUENT, a computational fluid dynamics (CFD) software package was... 

Proton exchange membrane (PEM) fuel cell performance is directly related to the bipolar plate design and their channels pattern. Power enhancements can be achieved by optimal design of the type, size, or patterns of the channels. It has been realized that the bipolar plate design has significant role on reactant transport as well as water management in a PEM Fuel cell. Present work concentrates on improvements in the fuel cell performance by optimization of flow-field design and channels configurations. A three-dimensional, multi-component numerical model of flow distribution based on Navier-Stokes equations using individual computer code is presented. The simulation results showed excellent... 

The performance of Co-flow fluidic thrust vectoring is a function of secondary flow characteristics and the fluidic nozzle geometry. In terms of nozzle geometry, wall shape and the secondary slot aspect ratio are the main parameters that control the vector angle. The present study aims to find a high quality wall shape to achieve the best thrust vectoring performance, which is characterized by the maximum thrust deflection angle with respect to the injected secondary air. A 3D computational fluid dynamics (CFD) model is employed to investigate the flow characteristics in thrust vectoring system. This model is validated using experimental data collected from the deflection of exhaust gases of... 

In this work, a supersonic turbulent flow over a long axisymmetric body was investigated, both experimentally and computationally. The experimental study consisted of a series of wind tunnel tests for the flow over an ogive-cylinder body at a Mach number of 1.6 and at a Reynolds number of 8 × 10 6, at angles of attack between -2 and 6 degrees. It included the surface static pressure and the boundary layer profile measurements. Further, the flow around the model was visualized using a Schlieren technique. All tests were conducted in the trisonic wind tunnel of the Qadr Research Center (QRC). Also, the same flow at zero angle of attack was computationally simulated using a multi-block grid... 

Mathematical simulation of non-isothermal multiphase flow in deformable unsaturated porous media is a complicated issue because of the need to employ multiple partial differential equations, the need to take into account mass and energy transfer between phases and because of the non-linear nature of the governing partial differential equations. In this paper, an analytical solution for analyzing a fully coupled problem is presented for the one-dimensional case where the coefficients of the system of equations are assumed to be constant for the entire domain. A major issue is the non-linearity of the governing equations, which is not considered in the analytical solution. In order to... 

Overall turbine analysis requires large CPU time and computer memory, even in the present days. As a result, choosing an appropriate computational domain accompanied by a suitable boundary condition can dramatically reduce the time cost of computations. This work compares different geometries for numerical investigation of the 3D flow in the runner of a Francis turbine, and presents an optimum geometry with least computational effort and desirable numerical accuracy. The numerical results are validated with a GAMM Francis Turbine runner, which was used as a test case (GAMM workshop on 3D computation of incompressible internal flows, 1989) in which the geometry and detailed best efficiency... 

Reynolds-Averaged Navier-Stokes (RANS) approach with the k-ε closure model is employed for the first time to simulate direct Solid-Phase Micro-Extraction (SPME) computationally. Simulations are performed by using COMSOL Multiphysics in order to examine methods to decrease the extraction time. Experiments are also conducted to support data obtained from the numerical framework. Di-n-Butyl Phthalate (DNBP) and etched steel wire are chosen as the analyte and the adsorbent, respectively. Stirring rate, fiber's location, stirrer magnet's size, and the method of sample rotation are examined to decrease the extraction time. In addition, the effects of adding a baffle to the vial and implementing a...