Sharif Digital Repository

This paper presents a new low-power comparator-reduced hybrid ADC. The proposed ADC uses dynamic comparators to perform a high-speed low-power conversion. In order to reduce the offset and kickback noise effect of conventional dynamic comparators, a new low-kickback noise comparator with a high pre-amplifier gain is presented. Two 4bit and 8bit ADCs are designed and simulated in 0.18 μm CMOS technology with 1.8 v supply voltage. INL and DNL of 4bit ADC are less than 0.4LSB and 0.5LSB, respectively, while 8bit ADC obtains DNL and INL of 0.83LSB and 1.3LSB, respectively. With ENOB of 3.6bit and 7.2bit for 4bit and 8bit ADCs, the 4bit ADC consumes only 1.7 mW at the sampling rate of 400 Ms/s... 

In this paper, the effect of imperfections on the behavior of N-path filters is investigated. Exact mathematical derivations are presented which describe the effect of clock skew and finite fall/rise time on the impedance transformation behavior of N-path filters. In the ideal case, the N-path filter is supposed to provide a short-circuit to the ground for undesired frequency contents and an open-circuit for the desired signal so that it lies within the passband of the filter. It is shown that clock skew and finite clock fall/rise time result in a non-zero impedance for frequency contents other than the clock frequency and a smaller impedance for the desired voltage. In a real circuit with... 

A low-power high-speed two-stage dynamic comparator is presented. In this circuit, PMOS transistors are used at the input of the first and second stages of the comparator. At the evaluation phase, the second stage is activated after the first stage with a predetermined delay to achieve a controllable pre-amplifier gain. Also, the first stage is turned off after the delay to reduce overall power consumption. Simulation results in 0.18 μτη CMOS technology, prove that the proposed circuit reduces the power consumption by a factor of two and reduces comparison time as large as 210ps in the same budget of offset voltage compared to the conventional circuit. Moreover, the offset voltage and power... 

A new switching method for the stabilisation of a one-dimensional capacitor array tank for the stepwise charging of a load capacitor is presented. In this method, the tank capacitor configuration is rearranged in a circular manner once the charging process of a load capacitor finishes and before the charging process of a new load capacitor begins. Unlike previously reported methods, this method does not require backward switching for the stabilisation of tank capacitor voltages. Hence, the proposed method reduces the number of charging process steps by a factor of up to 2 compared with the conventional method. Moreover, since the tank recycles its charge inherently, the capacitive load can... 

A new switched-capacitor digital to analog converter (DAC) is presented. In this DAC, a ladder of series capacitors is used to generate the output voltage levels. A correction phase is used to increase the precision of the DAC. It is analytically shown that the proposed DAC is mismatch independent by virtue of the correction phase. That is after few correction phases (typically one), the effect of mismatch on the reference voltage levels on the ladder diminishes and an accurate voltage division is provided. It is proven that the whole process sinks no extra charge from the power supply. Furthermore, post layout simulations in 0.18 μm technology proves the benefits of the proposed method  

An efficient layout technique is proposed to eliminate the effect of the bottom-plate capacitors in a C-2C Digital to Analog Converter (DAC). Using this technique, the bottom-plate capacitors of 2C capacitors in the C-2C structure are placed in parallel with 1C capacitors. Then, the effect of the bottom plate capacitors is nulled by modifying the size of the main 1C capacitors. Hence, avoiding the complexity of calibration, this technique can preclude the effect of the bottom-plate to ground capacitance. Statistical simulations prove that the proposed technique is robust to non-ideal effects such as mismatch or parasitic capacitors. A 10-bit C-2C DAC is modeled in COMSOL Multiphysics using... 

A low-power high-speed two-stage dynamic comparator is presented. In this circuit, the voltage swing of the first stage of the comparator, pre-amplifier stage, is limited to Vdd/2 in order to reduce the first stage power consumption. Also, this voltage swing limitation provides a strong drive at the evaluation phase for the second stage to enhance the comparison speed. Analytical derivations along with post layout simulation results prove that the proposed method speeds up the conventional circuit by a factor of two in the same budget of power consumption and offset voltage. Furthermore, the proposed circuit offers a wide input common mode range as large as the supply voltage while employing... 

A low-power technique to reduce the power consumption of the dynamic comparators is presented. Using this technique, the pre-ampli-fication phase of the comparator is stopped without any effect on the dynamic behaviour of the comparator. Therefore, the power consumption of the pre-amplifier stage which is the main part of the total power consumption is reduced significantly. Simulation results in various comparators reveal that the proposed technique reduces the total power consumption by more than 50%  

A new low-power switching procedure for stepwise capacitor chargers is presented. In this procedure, a novel displacement method is utilized to improve the speed by a factor of two while preserving energy efficiency. Moreover, the load capacitor retains its charge after the charging process finishes and permits the circuit charge another predischarged load capacitor without an efficiency degradation problem (instability). Also, the control circuit of the switching procedure is implemented using only flip-flops with no combinational logic, therefore, it systematically prevents glitch power dissipation and improves the efficiency. Analytical derivations are proposed to model the switching... 

An analytical method is presented to characterize stepwise adiabatic circuits (SACs). In this method, the SACs are modeled as a discrete time system. Unlike previous methods, the stability is verified for arbitrary load capacitor ratios. Moreover, this method presents analytical derivations to offer an area/energy efficient design methodology. MATLAB simulations, post-layout simulations in the CMOS 0.18 μm technology, silicon measurements, and measurements based on discrete components confirm the precision of the analytical derivations. Using the proposed design methodology, a capacitive tank has been designed which reduces the energy consumption by 20% while the total size of the tank... 

A low-power high-speed two-stage dynamic comparator is presented. The voltage fluctuation at the first stage of the comparator (pre-Amplifier stage) is limited to V dd=2. Therefore, the power consumption of the first stage which is the dominant part of the total power consumption is reduced. The output voltage of the first stage is kept above V dd=2. As a result, during the comparison the second stage of the comparator (latch) is activated stronger compared to the conventional comparator. To prove the benefits of the proposed comparator, the proposed and the other circuits are simulated in the equal budget of power and offset. Simulation results prove that the proposed comparator is faster... 

In this paper, a method is presented to reduce the power consumption of the two-stage dynamic comparators. In the two-stage dynamic comparators, the first stage (pre-amplifier stage) amplifies the input differential voltage. Then the second stage (latch stage) is activated and finishes the comparison. When the comparison is about to finish, the balance of the positive feedback of the latch stage tends to tilt toward one of the outputs; after this, to the end of the comparison, there is no need for additional pre-amplification gain which causes excess power consumption. In this paper, a method is proposed to eliminate this part of power consumption. It is shown that while reducing the power... 

A low-power technique for high-resolution comparators is introduced. In this technique, p-type metal-oxide-semiconductor field-effect transistors are employed as the input of the latch of the comparator just like the input of the preamplifier. The latch and preamplifier stages are activated in a special pattern using an inverter-based controller. Unlike the conventional comparator, the preamplification delay can be set to an optimum low value even if after the preamplification, the output voltages is less than n-channel metal-oxide semiconductor voltage threshold. As a result, the proposed comparator reduces the power consumption significantly and enhances the speed. The speed and power... 

A low-power comparator is presented. pMOS transistors are used at the input of the preamplifier of the comparator as well as the latch stage. Both stages are controlled by a special local clock generator. At the evaluation phase, the latch is activated with a delay to achieve enough preamplification gain and avoid excess power consumption. Meanwhile, small cross-coupled transistors increase the preamplifier gain and decrease the input common mode of the latch to strongly turn on the pMOS transistors (at the latch input) and reduce the delay. Unlike the conventional comparator, the proposed structure let us set the optimum delay for preamplification and avoid excess power consumption. The... 

In this paper, an analytic model of the energy consumption of the Stepwise Adiabatic Circuits (SAC) when it is possible to discharge the load capacitor is proposed. Using this model, analytical derivations are calculated which shows us the power saving of the SACs. Using analytical derivations, the sizing of a capacitor tank is determined for a desired energy saving. For example, the derivations predict that if the sizing of the 3-step series tank capacitors is equal to the load capacitor, the power saving is 55%. Also, if the sizing of the tank is very large the energy saving of a 3-step stepwise charging is equal to 66.7%. Several Simulations in 0.18μm CMOS technology prove the accuracy of... 

A new low-power switching procedure for stepwise capacitor chargers is presented. In this procedure, a novel displacement method is utilized to improve the speed by a factor of two while preserving energy efficiency. Moreover, the load capacitor retains its charge after the charging process finishes and permits the circuit charge another predischarged load capacitor without an efficiency degradation problem (instability). Also, the control circuit of the switching procedure is implemented using only flip-flops with no combinational logic, therefore, it systematically prevents glitch power dissipation and improves the efficiency. Analytical derivations are proposed to model the switching... 

A new structure of Capacitive Digital to Analog Converters (CDAC) for SAR ADCs is presented. In this structure, a number of capacitors are used in different series configurations to generate desirable voltage levels based on an input binary code. the proposed CDAC consumes a certain amount of power regardless of the input code. This method achieves more than 99.9% power reduction and 98.9% area reduction compared to the conventional binary weighted CDAC. © 2017 IEEE  

A new switched-capacitor Digital to Analog converter (DAC) is presented. In this method, a ladder of series capacitors is used to generate the output voltage levels. A correction phase is used to increase the precision of the DAC. It is analytically shown that the proposed DAC is mismatch and process independent by virtue of the correction phase. That is after some correction phases, the effect of mismatch on the reference voltage levels on the ladder diminishes and an accurate voltage division is provided. It is proven that the whole process sinks no extra charge from the power supply  

Mechanical shear connectors are commonly used to transfer longitudinal shear forces across the steel-concrete interface in composite beams. Steel pipe as a new shear connector is proposed in this research and its performance to achieve composite strength is investigated. Experimental monotonic push-out tests were carried out for this connector. Then, a nonlinear finite element model of the push-out specimens is developed and verified against test results. Further, the finite element model is used to investigate the effects of pipe thickness, length and diameter on the shear strength of the connectors. The ultimate strengths of these connectors are reported and their respective failure modes...