Sharif Digital Repository

The present study focuses on the simulation of two dimensional unsteady cavitating flows. For simulation of unsteady behaviors of cavitation which have practical applications, the development of unsteady PISO algorithm based on the non-conservative approach is utilized. For multi-phase simulation, single-fluid Navier-Stokes equations, along with the volume fraction transport equation, are employed. The bubble dynamics model is utilized to simulate phase change between vapor and liquid phases of the water. Unsteady simulation of cavitation around NACA66(MOD) and supercavitation around a flat plate normal to flow direction are performed to clarify accuracy of presented model. Numerical results... 

The present study focuses on the implementation of PISO algorithm to simulate cavitating flows. For simulation of unsteady behaviors of cavitation which have practical applications, the development of unsteady PISO algorithm based on the non-conservative approach is investigated. The effects of mixture compressibility are considered to improve accuracy of simulations. For multi-phase simulation, single-fluid Navier-Stokes equations, along with the volume fraction transport equation, are employed. The bubble dynamics model is utilized to simulate phase change. To prove capabilities of the developed PISO algorithm to simulate cavitating flows, unsteady simulation of cavitation around NACA0015... 

Phase separation is one of the common methods for fabrication of polymeric membrane, which classifies into the categories of Thermally Induced Phase Separation (TIPS) and Nonsolvent Induced Phase Separation (NIPS), i.e. heat and mass transfer induced phase separation, respectively. NIPS has been applied more commonly than TIPS, but the membranes which have resulted from this technique have macro finger-like voids, weak mechanical strength and not high separation ability in comparison with the TIPS. In contrast, membranes produced by the TIPS method have micro scale pores, high mechanical strength and also high separation capability, however, polymeric solutions prepared at high temperatures... 

Thermal cracking is the prevalent type of distress experienced by asphalt pavements in cold regions. It is widely assumed that when thermal stresses induced in the pavement exceed the tensile strength of the asphalt surface layer, cracking occurs; however, the role of thermal fatigue should not be ignored. To better describe the low-temperature (LT) performance properties of modified asphalt binders, a new parameter, normalised tensile stress (NTS), was defined in this research. NTS values were compared with bending beam rheometer (BBR), direct tension (DT) and semi-circular bending (SCB) fracture test results. The m-value parameter of the BBR test specifies the type of asphalt binder. This... 

General purpose software is developed to simulate 6-DoF fluid-structure interaction in two-phase viscous flow. It is a VoF-fractional step solver based on the finite-volume discretization which uses a boundary-fitted body-attached hexahedral grid as the motion simulation strategy. As an application, a high-speed planing catamaran is simulated in steady forward motion as well as in turning maneuver. Results are compared with the available data and good qualitative and quantitative agreements are achieved. Numerical schemes and the solution algorithm of the software are consistent and show a good capability to model highly nonlinear ship motions. It can be further developed to represent a more... 

Thermal cracking is the prevalent type of distress experienced by asphalt pavements in cold regions. It is widely assumed that when thermal stresses induced in the pavement exceed the tensile strength of the asphalt surface layer, cracking occurs; however, the role of thermal fatigue should not be ignored. To better describe the low-temperature (LT) performance properties of modified asphalt binders, a new parameter, normalised tensile stress (NTS), was defined in this research. NTS values were compared with bending beam rheometer (BBR), direct tension (DT) and semi-circular bending (SCB) fracture test results. The m-value parameter of the BBR test specifies the type of asphalt binder. This... 

Purpose - This study aims to present compatible computational fluid dynamics procedure for calculation of incompressible three-dimensional time-dependent flow with complicated free surface deformation. A computer software is developed and validated using a variety of academic test cases. Design/methodology/approach - Two fluids are modeled as a single continuum with a fluid property jump at the interface by solving a scalar transport equation for volume fraction. In conjunction, the conservation equations for mass and momentum are solved using fractional step method. Here, a finite volume discretisation and colocated arrangement are used. Findings - The developed code results in accurate... 

Asphalt binder is responsible for the thermo-viscoelastic mechanical behavior of asphalt concrete. Upon application of pure compressive stress to an asphalt concrete specimen, the stress is transferred by mechanisms such as aggregate interlock and the adhesion/cohesion properties of asphalt mastic. In the pure tensile stress mode, aggregate interlock plays a limited role in stress transfer, and the mastic phase plays the dominant role through its adhesive/cohesive and viscoelastic properties. Under actual combined loading patterns, any coordinate direction may experience different stress modes; therefore, the mechanical behavior is not the same in the different directions and the asphalt... 

Asphalt binder is responsible for the thermo-viscoelastic mechanical behavior of asphalt concrete. Upon application of pure compressive stress to an asphalt concrete specimen, the stress is transferred by mechanisms such as aggregate interlock and the adhesion/cohesion properties of asphalt mastic. In the pure tensile stress mode, aggregate interlock plays a limited role in stress transfer, and the mastic phase plays the dominant role through its adhesive/cohesive and viscoelastic properties. Under actual combined loading patterns, any coordinate direction may experience different stress modes; therefore, the mechanical behavior is not the same in the different directions and the asphalt... 

The application of agricultural fibers for making particleboards has been studied in two types of composites: (i) type I particleboards were composites of wheat straw and rice husk fibers with polymeric methylene di-phenyl diisocyanate resin (pMDI) as a binder made by compression moulding; (ii) type II particleboards were composites of rice husk and polypropylene made by extrusion and injection moulding. In type I particleboards, the effects of varying the resin content and various combinations of wheat straw/rice husk fibers were investigated and characterised in terms of physical and mechanical properties of particle boards such as modulus of rupture, modulus of elasticity, compression... 

Through the strategic highway research program (SHRP) project, time-temperature superposition (TTS) was used to reduce the loading time of bending beam rheometer (BBR) test. Based on TTS, stiffness of the asphalt binder after a two-hour loading time is similar to that after 60 s at 10 °C above. This study attempted to evaluate the TTS validity using finite element (FE) method by developing master curves in a broad range of low temperatures. The results indicated that TTS was neither valid for modified asphalt binders nor for neat binder. Also, in addition to the loading time dependency of m-value, limiting values of stiffness and m-value find no rheological acceptance. As a remedy, thermally... 

Incorporation of reclaimed asphalt pavement (RAP) and crumb rubber (CR) materials into asphalt mixtures have been of great importance from sustainability point of view. Although, inclusion of RAP materials in asphalt mixtures improves the rutting resistance at high temperature, the low temperature (LT) and intermediate temperature (IT) cracking performance of RAP mixtures may need additional considerations. In this regard, different schemes of modification have been applied to RAP mixtures to address its performance weaknesses. This study evaluated the effect of RAP and CR in combination with Sasobit and hydrated lime on the cracking performance of asphalt mixtures. The LT and IT... 

Background and purpose of the study. Carbon nanotubes (CNTs) are emerging drug and imaging carrier systems which show significant versatility. One of the extraordinary characteristics of CNTs as Magnetic Resonance Imaging (MRI) contrasting agent is the extremely large proton relaxivities when loaded with gadolinium ion (Gdn 3+) clusters. Methods. In this study equated Gdn 3+ clusters were loaded in the sidewall defects of oxidized multiwalled (MW) CNTs. The amount of loaded gadolinium ion into the MWCNTs was quantified by inductively coupled plasma (ICP) method. To improve water solubility and biocompatibility of the system, the complexes were functionalized using diamine-terminated... 

In vivo dose-dependent effects of nanoscale graphene oxide (NGO) sheets on reproduction capability of Balb/C mice were investigated. Biodistribution study of the NGO sheets (intravenously injected into male mice at dose of ∼2000 μg/mL or 4 mg/kg of body weight) showed a high graphene uptake in testis. Hence, in vivo effects of the NGO sheets on important characteristics of spermatozoa (including their viability, morphology, kinetics, DNA damage and chromosomal aberration) were evaluated. Significant in vivo effects was found at the injected concentrations ≥200 μg/mL after (e.g., ∼45% reduction in sperm viability and motility at 2000 μg/mL). Observation of remarkable DNA fragmentations and...