Sharif Digital Repository

We have performed molecular dynamics simulation on B-DNA duplex (CGCGAATTGCGC) at different temperatures. The DNA was immerged in a salt-water medium with 1 M NaCl concentration to investigate salt effect on the denaturation process. At each temperature, configurational entropy is estimated using the covariance matrix of atom-positional fluctuations, from which the melting temperature (T m) was found to be 349 K. The calculated configuration entropy for different bases shows that the melting process involves more peeling (including fraying from the ends) conformations, and therefore the untwisting of the duplex and peeling states form the transition state of the denaturation process. There... 

In precipitation hardenable materials, it is desirable to determine the precipitate dissolution temperature for homogenizing the microstructure by controlling the size and distribution of the precipitates. In this research, the influence of various heat treatment and hot deformation conditions on the kinetics of γ ′ dissolution and its morphological evolution in Nimonic 115 was studied. In addition, hot deformation behavior of the material was investigated using hot compression experiments at varying temperature (between 1,050°C and 1,175°C) and strain rates (between 0.01 and 1 s-1) up to a true strain of 0.8. The values obtained for the solvus temperature of γ ′ precipitates by two methods... 

In this work, the effect of hot deformation temperature on microstructure and mechanical properties of micro alloyed steel was studied. The results indicated that by decreasing the deformation temperature final microstructure is refined and the volume fraction of grain boundary ferrite is increased and some pearlite is produced. Therefore both the yield strength and ultimate tensile strength is increased, while the toughness is preserved in comparison to a ferritic-pearlitic microstructure. Also a model was developed to relate the deformation condition to the volume fraction of acicular ferrite at mixed microstructure. © 2008 Elsevier Ltd. All rights reserved  

The initial and subsequent yield surfaces for architected pyramidal lattice materials are investigated analytically. Considering lattice struts as elastic-perfectly plastic thin beams subjected to both axial force and bending moment, a set of nonlinear elastic-plastic constitutive relations for a strut is proposed. Moreover, we phenomenologically present anisotropic pressure-dependent yield functions for pyramidal lattices. Comparison of planar yield surfaces of pyramidal lattices predicted by analytical approach to the ones obtained from phenomenological models shows a good agreement for the type of external loads and range of strains investigated in this study. Investigating the normality... 

We investigate a one-dimensional (1-D) Ising model for finite-site systems. The finite-site free energy and the surface free energy are calculated via the transfer matrix method. We show that, at high magnetic fields, the surface free energy has an asymptotic limit. The absolute surface energy increases when the value of f (the ratio of magnetic field to nearest-neighbor interactions) increases, and for f ≥10 approaches a constant value. For the values of f ≥0.2, the finite-site free energy also increases, but slowly. The thermodynamic limit in which physical properties approach the bulk value is also explored  

The effect of cooling rate after hot deformation on the microstructure and mechanical properties of a commercial microalloyed forging steel (30MSV6 grade) was investigated using the hot compression test. Hot compression test was performed at 1150 and 925 °C followed by air cooling at different rates. Final microstructures and mechanical properties were evaluated by optical microscopy and shear punch test (SPT), respectively. The results indicated that by increasing the cooling rate, the as-received ferritic-pearlitic microstructure changes to the acicular ferrite, bainite or martensite. It is shown that both yield and ultimate strength increase but the ductility decreases significantly. At a... 

Photovoltaic (PV) panels provide a suitable way for the direct conversion of solar energy into electricity. The electrical output and efficiency of PV modules are dependent on working temperature. The present study contributes to investigate the efficiency of utilizing a flat plate closed-loop pulsating heat pipe (CLPHP) to cool down a PV panel in both thermal and economic aspects. Accordingly, a numerical investigation is employed to obtain the surface temperature and electrical gain of the PV panel through four scenarios, including natural cooling without additional equipment, CLPHP-based passive cooling, CLPHP-based active cooling, and a conventional flat plate cooling methods. The... 

In this work, hot tension tests were conducted on as cast and wrought samples of a high carbon high chromium tool steel to study the hot workability under the rolling conditions. The flow curves illustrate the classical shape of dynamic recrystallization (DRX). It is observed that broken carbide nets in the wrought samples result in lower deformation activation energy 398. kJ/mol in comparison to the as cast samples 432. kJ/mol. Necking strains were calculated using the inflection point of the work-hardening (θ) vs. stress curves. Wrought samples show higher hot ductility and lower maximum stress than the as cast ones. It is shown that lower activation energy of deformation and lower stress... 

In this research a computer model based on elasto hydrodynamic fluid film lubrication is developed in order to calculate the torque transmission efficiency of a half-toroidal CVT variator. Validation of this model is verified by comparing the experimental and the model results. Sensitivity of torque transmission efficiency to eleven parameters is investigated. These parameters are: dimensionless roller curvature, aspect ratio, half cone angle, fluid viscosity index, pressure constant for Roelands model, input rotational velocity, absolute viscosity at atmospheric pressure, Young modulus of disks and power rollers, Poisson ratio of disks and power rollers, number of power rollers and variator... 

In this research a model is developed which calculates the torque transmission efficiency of a half-toroidal CVT as a function of variator geometry, gear ratio and input torque. The different criteria which are considered to be important in a half toroidal CVT performance are torque transmission efficiency, variator weight, roller fatigue life and bearing torque loss. Variation of geometrical characteristics such as roller curvature, number of power rollers, aspect ratio and half cone angle affect these criteria in different ways. Therefore, in order to find the optimal quantity for each geometrical parameter an optimization problem should be developed. The objective function of this...