Loading...
Search for:
young-modulus
0.007 seconds
Total 51 records
Evaluation of Material Properties of Short Carbon Nanotube-Based Composites Using Nonlocal ElasticityTheory
, M.Sc. Thesis Sharif University of Technology ; Naghdabadi, Reza (Supervisor)
Abstract
Classical theory of elasticity, which is founded upon results of mechanical experiments on the large scale materials, has reasonable results in predicting mechanical properties. The basic idea in this theory is that stress at a point of the material is only a function of the local strain and it is independent of the nonlocal strains. Therefore, the size of the material does not play any role in analyzing mechanical behavior of materials using this theory. However, results from experiments and atomic simulations have shown that in nano scale materials, such as carbon nanotubes (CNTs) and their composites, mechanical properties are strongly dependent on the size parameters of these materials....
Using Surface Properties of Immiscible Fluids in Capillary Tubes for Identification and Separation of Cancerous Blood Cells
, M.Sc. Thesis Sharif University of Technology ; Ayatollahi, Shahabodin (Supervisor) ; Vossoughi, Manochehr (Supervisor)
Abstract
Cancer has been known as one of the main reasons for disease-related deaths in the last decades. Early diagnosis could significantly reduce the level of fatality chances. Among the known cancer types, lung cancer is one of the most malignant ones. The common diagnosticmethods are expensive and using high-technology methods; therefore, the introduction of simple and cheap methods is very urgent to detect it. In this project, surface and interfacial tension measurement of cancerous and normal lung cells have been investigated as an easy detection technique. Among the common measurement methods, Pendant Drop and Capillary height techniques have been utilized in this research work. The obtained...
Experimental Investigation for FINDING a Suitable Additive (Nanoparticle) to Design Required Elastic Cement for Iranian Oil/Gas Wells
, M.Sc. Thesis Sharif University of Technology ; Taghikhani, Vahid (Supervisor) ; Soltanian, Hamid (Supervisor) ; Moghadasi, Jamshid (Supervisor) ; Samsam Sokheiravi, Mohammad (Co-Advisor)
Abstract
Previous studies indicate that increasing cement compressive strength can’t prevent loss of zonal isolation and casing collapse in worse case during well operations or formation loading. Since standard cements with high compressive strength can’t solve these problems, so application of elastic cements with low Young’s modulus and high Poisson’s ratio becomes important. These cements sustain generated stresses during well operations and prevent creation of point loads when formation creep occurs. For this purpose, a new additive was designed in order to improve the cement elasticity and tensile strength. It is a nanoparticle and named EX-RIPI (by Research Institute of Petroleum Industry,...
3D Bioprinting of oxygenated cell-laden gelatin methacryloyl constructs
, Article Advanced Healthcare Materials ; Volume 9, Issue 15 , 2020 ; Darabi, M. A ; Nasiri, R ; Sangabathuni, S ; Ertas, Y. N ; Alem, H ; Hosseini, V ; Shamloo, A ; Nasr, A. S ; Ahadian, S ; Dokmeci, M. R ; Khademhosseini, A ; Ashammakhi, N ; Sharif University of Technology
Wiley-VCH Verlag
2020
Abstract
Cell survival during the early stages of transplantation and before new blood vessels formation is a major challenge in translational applications of 3D bioprinted tissues. Supplementing oxygen (O2) to transplanted cells via an O2 generating source such as calcium peroxide (CPO) is an attractive approach to ensure cell viability. Calcium peroxide also produces calcium hydroxide that reduces the viscosity of bioinks, which is a limiting factor for bioprinting. Therefore, adapting this solution into 3D bioprinting is of significant importance. In this study, a gelatin methacryloyl (GelMA) bioink that is optimized in terms of pH and viscosity is developed. The improved rheological properties...
Effect of microthread design of dental implants on stress and strain patterns: A three-dimensional finite element analysis
, Article Biomedizinische Technik ; Volume 58, Issue 5 , September , 2013 , Pages 457-467 ; 00135585 (ISSN) ; Raoofi, S ; Kadkhodazadeh, M ; Movahhedi, M. R ; Khademi, M ; Sharif University of Technology
Walter de Gruyter and Co
2013
Abstract
The aim of this study was to use finite element analysis (FEA) to assess the influence of microthread design at the implant neck on stress distribution in the surrounding bone. A commercially available implant with 3.5 mm diameter and 10.5 mm length was selected and used as a model. For the purpose of designing the microthread implant model, microthreads were added to the implant neck in a computerized model. A force measuring 100 N was then applied to the entire surface of the abutment in the vertical direction. The results showed that in both models, stress was mainly concentrated at the cortical bone adjacent to the neck of the implant. Maximum stress values in the cortical bone...
Design of an effective piezoelectric microcantilever biosensor for rapid detection of COVID-19
, Article Journal of Medical Engineering and Technology ; Volume 45, Issue 6 , 2021 , Pages 423-433 ; 03091902 (ISSN) ; Merati, M ; Abdekhodaie, M. J ; Sharif University of Technology
Taylor and Francis Ltd
2021
Abstract
Acute respiratory syndrome coronavirus 2 (SARS-CoV-2), also called COVID-19, is one of the most contagious viruses resulting in a progressive pandemic. Since specific antiviral treatments have not been developed yet and its fatal rate is almost high, early and fast detection is critical for controlling the outbreak. In this study, a piezoelectric microcantilever biosensor has been designed for detecting COVID-19 samples directly without requiring preparation steps. The biosensor acts as a transducer and is coated with the related antibody. When the SARS-CoV-2 antigens adsorbed on the microcantilever top surface through their spike proteins, a surface stress due to the mass change would be...
Nanomechanical properties of MscL α helices: A steered molecular dynamics study
, Article Channels ; Volume 11, Issue 3 , 2017 , Pages 209-223 ; 19336950 (ISSN) ; Bavi, O ; Vossoughi, M ; Naghdabadi, R ; Hill, A. P ; Martinac, B ; Jamali, Y ; Sharif University of Technology
Taylor and Francis Inc
2017
Abstract
Gating of mechanosensitive (MS) channels is driven by a hierarchical cascade of movements and deformations of transmembrane helices in response to bilayer tension. Determining the intrinsic mechanical properties of the individual transmembrane helices is therefore central to understanding the intricacies of the gating mechanism of MS channels. We used a constant-force steered molecular dynamics (SMD) approach to perform unidirectional pulling tests on all the helices of MscL in M. tuberculosis and E. coli homologs. Using this method, we could overcome the issues encountered with the commonly used constant-velocity SMD simulations, such as low mechanical stability of the helix during...
Proposing a new model to approximate the elasticity modulus of granite rock samples based on laboratory tests results
, Article Bulletin of Engineering Geology and the Environment ; Volume 78, Issue 3 , 2019 , Pages 1527-1536 ; 14359529 (ISSN) ; Esfandi Sarafraz, M ; Hasanipanah, M ; Mojtahedi, S. F. F ; Tahir, M. M ; Sharif University of Technology
Springer Verlag
2019
Abstract
An accurate examination of deformability of rock samples in response to any change in stresses is deeply dependent on the reliable determination of properties of the rock as analysis inputs. Although Young’s modulus (E) can provide valuable characteristics of the rock material deformation, the direct determination of E is considered a time-consuming and complicated analysis. The present study is aimed to introduce a new hybrid intelligent model to predict the E of granitic rock samples. Hence, a series of granitic block samples were collected from the face of a water transfer tunnel excavated in Malaysia and transferred to laboratory to conduct rock index tests for E prediction. Rock index...
Modeling vibrational behavior of silicon nanowires using accelerated molecular dynamics simulations
, Article Scientia Iranica ; Volume 27, Issue 2 , 2021 , Pages 819-827 ; 10263098 (ISSN) ; Delafrouz, P ; Sharif University of Technology
Sharif University of Technology
2021
Abstract
The classical methods utilized for modeling nano-scale systems are not practical because of the enlarged surface e ects that appear at small dimensions. Contrarily, implementing more accurate methods is followed by prolonged computations as these methods are highly dependent on quantum and atomistic models, and they can be employed for very small sizes in brief time periods. In order to speed up the Molecular Dynamics (MD) simulations of the silicon structures, Coarse-Graining (CG) models are put forward in this research. The procedure involves establishing a map between the main structure's atoms and the beads comprising the CG model and modifying the parameters of the system so that the...
In situ forming interpenetrating hydrogels of hyaluronic acid hybridized with iron oxide nanoparticles
, Article Biomaterials Science ; Volume 3, Issue 11 , Aug , 2015 , Pages 1466-1474 ; 20474830 (ISSN) ; Shi, L ; Bagheri, R ; Kabiri, K ; Hilborn, J ; Ossipov, D. A ; Sharif University of Technology
Royal Society of Chemistry
2015
Abstract
Four derivatives of hyaluronic acid (HA) bearing thiol (HA-SH), hydrazide (HA-hy), 2-dithiopyridyl (HA-SSPy), and aldehyde groups (HA-al) respectively were synthesized. Thiol and 2-dithiopyridyl as well as hydrazide and aldehyde make up two chemically orthogonal pairs of chemo-selective functionalities that allow in situ formation of interpenetrating (IPN) disulfide and hydrazone networks simultaneously upon the mixing of the above derivatives at once. The formation of IPN was demonstrated by comparing it with the formulations of the same total HA concentration but lacking one of the reactive components. The hydrogel composed of all four components was characterized by a larger elastic...
Melt electrowriting of PLA, PCL, and composite PLA/PCL scaffolds for tissue engineering application
, Article Scientific Reports ; Volume 12, Issue 1 , 2022 ; 20452322 (ISSN) ; Seifi, S ; Akbari, A ; Mohammadi, K ; Shamloo, A ; Movahhedy, M. R ; Sharif University of Technology
Nature Research
2022
Abstract
Fabrication of well-ordered and bio-mimetic scaffolds is one of the most important research lines in tissue engineering. Different techniques have been utilized to achieve this goal, however, each method has its own disadvantages. Recently, melt electrowriting (MEW) as a technique for fabrication of well-organized scaffolds has attracted the researchers’ attention due to simultaneous use of principles of additive manufacturing and electrohydrodynamic phenomena. In previous research studies, polycaprolactone (PCL) has been mostly used in MEW process. PCL is a biocompatible polymer with characteristics that make it easy to fabricate well-arranged structures using MEW device. However, the...
Comparison of the mechanical properties of NiTi/Cu bilayer by nanoindentation and tensile test: Molecular dynamics simulation
, Article Materials Research Express ; Volume 3, Issue 12 , 2016 ; 20531591 (ISSN) ; Vahedpour, M ; Sadrnezhaad, S. K ; Sharif University of Technology
Institute of Physics Publishing
2016
Abstract
Molecular dynamics simulation was used to study of mechanical properties of NiTi/Cu bilayer by nanoindentation and tensile testing. A comparison has been made among mechanical properties measured and plastic deformation process at different copper thickness during nanoindnetation and tensile test of the samples. Embedded atom method potentials for describing of inter-Atomic interaction and Nose-Hoover thermostat and barostat are employed in the simulation at 400 K. The results showed that as the copper film thickness decreased, the maximum load and hardness values increased during nanoindetation. Saha and Nix model is used to describe reduced young's modulus behaviour of the bilayer system...
Determination of surface properties and elastic constants of FCC metals: A comparison among different EAM potentials in thin film and bulk scale
, Article Materials Research Express ; Volume 6, Issue 1 , 2019 ; 20531591 (ISSN) ; Yousefi, F. S ; Taghibakhshi, A ; Sharif University of Technology
Institute of Physics Publishing
2019
Abstract
Three independent elastic constants C 11, C 12, and C 44 were calculated and compared using available potentials of eight different metals with FCC crystal structure; Gold, Silver, Copper, Nickel, Platinum, Palladium, Aluminum and Lead. In order to calculate the elastic constants, the second derivative of the energy density of each system was calculated with respect to different directions of strains. Each set of the elastic constants of the metals in bulk scale was compared with experimental results, and the average relative error was for each was calculated and compared with other available potentials. Then, using the Voigt-Reuss-Hill method, approximated values for Young and shear moduli...
Chitosan-gelatin sheets as scaffolds for muscle tissue engineering
, Article Artificial Cells, Nanomedicine and Biotechnology ; Volume 43, Issue 2 , Nov , 2015 , Pages 124-132 ; 21691401 (ISSN) ; Mashayekhan, S ; Nazaripouya, A ; Naji, M ; Hunkeler, D ; Rajabi Zeleti, S ; Sharifiaghdas, F ; Sharif University of Technology
Informa Healthcare
2015
Abstract
Hydrogels made of natural polymers [chitosan (CS) and gelatin (G)] have been prepared having mechanical properties similar to those of muscle tissues. In this study, the effect of polymer concentration and scaffold stiffness on the behavior of seeded muscle-derived cells (MDCs) on the CS-G hydrogel sheets has been evaluated. Both variables were found to be important in cell viability. Viability was assessed by observation of the cell morphology after 1 day as well as a 14-day MTT assay. The CS-G hydrogels were characterized using Fourier transform infrared (FTIR) analysis, which revealed evidences of strong intermolecular interactions between CS and G. Hydrogel samples with intermediate...
A three-dimensional micromechanical model of brain white matter with histology-informed probabilistic distribution of axonal fibers
, Article Journal of the Mechanical Behavior of Biomedical Materials ; Volume 88 , 2018 , Pages 288-295 ; 17516161 (ISSN) ; Farahmand, F ; Shamloo, A ; Sharif University of Technology
Elsevier Ltd
2018
Abstract
This paper presents a three-dimensional micromechanical model of brain white matter tissue as a transversely isotropic soft composite described by the generalized Ogden hyperelastic model. The embedded element technique, with corrected stiffness redundancy in large deformations, was used for the embedment of a histology-informed probabilistic distribution of the axonal fibers in the extracellular matrix. The model was linked to a multi-objective, multi-parametric optimization algorithm, using the response surface methodology, for characterization of material properties of the axonal fibers and extracellular matrix in an inverse finite element analysis. The optimum hyperelastic...
Porous shape memory dental implant by reactive sintering of TiH2–Ni-Urea mixture
, Article Materials Science and Engineering C ; Volume 107 , 2020 ; Sadrnezhaad, S .K ; Hosseini, S. A ; Sharif University of Technology
Elsevier Ltd
2020
Abstract
We produced bifurcated bone-like shape memory implant (BL-SMI) with desirable tooth-root fixation capability by compact-sintering of TiH2–Ni-urea mixture. The primary constituents of the porous product were Ni and Ti. We could adjust the pores' shape, size, and interconnectivity for favorite bone ingrowth by using urea as a space holder. Without urea, we obtained an average porosity of 0.30, and a mean void size of 100 μm. With 70 vol % urea, we got 62% interconnected pores of 400 μm average size. Aging allowed us to tune the austenite-martensite transformation temperatures towards the needed body tissue arouse. Differential scanning calorimetry measured the transformation temperatures....
Fabrication and evaluation of a bilayer hydrogel-electrospinning scaffold prepared by the freeze-gelation method
, Article Journal of Biomechanics ; Volume 98 , 2020 ; Shamloo, A ; Sharif University of Technology
Elsevier Ltd
2020
Abstract
This study presents a bilayer structure as a skin scaffold comprised of an electrospun sheet layer made of polycaprolactone and polyvinil alcohol and a porous hydrogel layer made of chitosan and gelatin. The hydrogel layer was fabricated by employing the freeze-gelation technique. The bilayer structure was achieved by pouring the hydrogel solution on the electrospun sheet at the bottom of a mold followed by the freeze-gelation technique to obtain a porous structure in the hydrogel. The hydrogel and hydrogel-electrospun samples were characterized by scanning electron microscopy, swelling, tensile strength, in vitro and in vivo analyses. From a mechanical strength standpoint, the combination...
A hybrid scaffold of gelatin glycosaminoglycan matrix and fibrin as a carrier of human corneal fibroblast cells
, Article Materials Science and Engineering C ; Volume 118 , 2021 ; 09284931 (ISSN) ; Mahdavi salimi, S ; Abdekhodaie, M. J ; Baradaran Rafii, A ; Tabatabei, M. R ; Mehrvar, M ; Sharif University of Technology
Elsevier Ltd
2021
Abstract
A hybrid scaffold of gelatin-glycosaminoglycan matrix and fibrin (FGG) has been synthesized to improve the mechanical properties, degradation time and cell response of fibrin-like scaffolds. The FGG scaffold was fabricated by optimizing some properties of fibrin-only gel and gelatin-glycosaminoglycan (GG) scaffolds. Mechanical analysis of optimized fibrin-only gel showed the Young module and tensile strength of up to 72 and 121 KPa, respectively. Significantly, the nine-fold increase in the Young modulus and a seven-fold increase in tensile strength was observed when fibrin reinforced with GG scaffold. Additionally, the results demonstrated that the degradation time of fibrin was enhanced...
Mechanical properties of ester- and ether-DPhPC bilayers: A molecular dynamics study
, Article Journal of the Mechanical Behavior of Biomedical Materials ; Volume 117 , 2021 ; 17516161 (ISSN) ; Jamali, Y ; Tajkhorshid, E ; Bavi, O ; Pishkenari, H. N ; Sharif University of Technology
Elsevier Ltd
2021
Abstract
In addition to its biological importance, DPhPC lipid bilayers are widely used in droplet bilayers, study of integral membrane proteins, drug delivery systems as well as patch-clamp electrophysiology of ion channels, yet their mechanical properties are not fully measured. Herein, we examined the effect of the ether linkage on the mechanical properties of ester- and ether-DPhPC lipid bilayers using all-atom molecular dynamics simulation. The values of area per lipid, thickness, intrinsic lateral pressure profile, order parameter, and elasticity moduli were estimated using various computational frameworks and were compared with available experimental values. Overall, a good agreement was...
Development of HAp/GO/Ag coating on 316 LVM implant for medical applications
, Article Journal of the Mechanical Behavior of Biomedical Materials ; Volume 126 , 2022 ; 17516161 (ISSN) ; Izanloo, S ; Sharif University of Technology
Elsevier Ltd
2022
Abstract
In this study, antibacterial activity, biocompatibility, and corrosion resistance of 316 LVM implants were improved using the development of HAp/GO/Ag nanocomposite coatings by the dip-coating method. The XRD and FTIR results confirmed the synthesis of HAp/GO/Ag nanocomposites. HAp/Ag nanoparticles (68 nm) bound to epoxy, hydroxyl, and carboxyl functional groups on GO sheets (size of GO sheets varies from 255 to 1480 nm) by electrostatic interaction. FESEM images showed that HAp/GO/Ag coatings had higher density and fewer micro-cracks than pure HAp coatings. In addition, HAp/GO/Ag coatings showed optimized nano-hardness (4.5 GPa) and elasticity modulus (123 GPa). The results of...