Sharif Digital Repository

One of the most important problems in using wind energy is the estimation of wind energy potential of a region with acceptable accuracy. To use wind energy and convert it to electrical energy it is necessary to study the economical aspects of wind farm installation, and to choose an appropriate wind turbine to be installed in a region. To do such a study and to choose approperiate wind turbine, annual energy output of different wind turbines should be estimated in that region. The porpuse of this thesis is to develop new methods to estimate annual energy production of a wind turbine by using some of the parameters of wind speed pattern of a region such as wind speed average, wind speed... 

Flameless Combustion was experimentally studied. In this combustion mode, inlet air is preheated and products are recirculated inside the chamber. Therefore, the reaction zone is spread from a limited front to a wider area with that of a lower peak temperature and very lower Nitrogen Oxides (NOx) production. Controllable parameters are preheating temperature, equivalence ratio, and fuel and air mass flow rates. Applying similar conditions, the flameless combustion was compared to the diffusion flame. Measurable parameters are exhaust temperature and composition, including NOx. Reaction zone homogeneity is observed by photographing inside the combustion chamber through its visual access... 

Well worn gas turbine blade made of Nickel based superalloy, IN738LC was remelted due to remove inclusion and use it in casting process of new blade after microstrucrure investigation in neutral atmosphere and vacuum. The composition of slags for removing inclusions used for this practice were 70CaF2-20CaO-10Al2O3 and 55CaO-45Al2O3. The microstructural characterization involved use both optical as well as electron microscope including application of EDS technique for denoted the type of carbides and inclusion investigation. Chemical composition was determined by despersive spectroscopy method. The changing in main elements were reported too low. Number of inclusions were decreased in the... 

Vibrational modeling of a gas turbine considering simultaneous faults is considered. Faults including: unbalance, misalignment, and rotor crack are selected to be modeled. Oil film forces of hydrodynamic bearings are chosen as the supports of the rotor. Modeling starts with choosing an appropriate finite element model for the rotor which includes the effects of shear deflection, rotary inertia, gyroscopic moment, and rotor cross section variation. Modeling of unbalance is in fact a part of rotor finite element modeling. The forces that origniate form misalignment are computed using the static relations of a rigid coupling. Modeling of bearing faults along with bearing forces is performed... 

Application of wind energy and specially wind turbines as a green source of energy is getting more popular and as a result, the knowledge of wind energy has been improved dramatically. The purpose of this research is to determine the flow characteristics in the boundary layer profile over an airfoil which is used in a wind turbine blade. The model is sinusoidally oscillated in pitch. For the present study, the critical cross section of the wind turbine blade has been selected and the boundary layer velocity profiles over its airfoil have been investigated experimentally. Dynamic motion is produced with sinusoidal oscillator and the reduced frequency is varied in the range of 0.054 to 0.1.... 

Because of the importance and value of Superalloy, In this research has been treid to remelting scrap of gas turbine blades cobalt based Superalloy X-45, In order to restore it to the cycle of consumption. For this purpose, scraps were remelted under different conditions, for example changing the atmosphere, changing slag composition, changing type of the furnace for remelting and changing time of remelting process. Then in order to investigate effect of the above factors, microstructure were studied by optical microscope and Scanning Electron Microscopy (SEM) And also in order to investigate changings of element composition, chemical analysis were examined by atomic absorption analysis and... 

In this research a special Three-Phase to Single-Phase converter has been proposed to connect a three-phase Permanent Magnet Synchronous Generator (PMSG) of a wind turbine to a single-phase network. Common back-to-back converter used for this application employs a bulk capacitor in its DC link to generate the pulsating component of the single-phase side instantaneous power. This capacitor is costly and reduces system overall reliability. This problem is alleviated in this work by providing the single-phase load pulsating power using the PMSG large inductances. The proposed system leaves the PMSG torque ripple-free while providing the single-phase load power. With the help of this method,... 

On account of the exhausting nature and increasing daily cost of the fossil fuels, it seems that replacing the fossil fuels by an alternative source of energy is inevitable. Moreover, in the remote areas that the electricity network is not accessible, the use of distributed sources (DSs) such as solar energy and wind energy is advantageous. Continuity of the supply and voltage control of the load in spite of the stochastic nature of the generated power of the renewable energy resources are the main concerns in the distributed generation (DG) systems. In this thesis, stand-alone operation of a DG unit comprising a solar unit and wind turbine as primary sources of energy is considered. A... 

Permanent-magnet synchronous generators have attracted more attention in recent years due to their special advantages which make them a suitable option for variable-speed wind turbines.Low-voltage ride through capability is one of the main concerns in widespread use of wind turbines in electric grids. Nowadays wind turbines are expected to remain connected to the grid during voltage dips and support the voltage recovery process by supplying reactive power.This thesis aims at behavior analysis and performance improvement of permanent-magnet synchronous generator-based wind turbines during grid faults. A simple method is presented to overcome the over current problem of the grid-side converter... 

This thesis studies the economic feasibility of replacing a throttling valve with an expansion turbine in a city gate station for the purpose of distributed electricity generation through exergy recovery from pressurized natural gas. Conventionally, high pressure natural gas stream enters a pressure reduction station with its physical exergy completely destroyed in an irreversible Joule-Thompson effect of a throttling valve. To avoid hydrate formation at the outlet of the turboexpander, the inlet stream should be preheated. Although pressure reduction stations are inherently subject to seasonal fluctuations of inlet natural gas pressure and flow rate, the preheating temperature should be... 

Compressor stations with gas turbine drive have become common in transport of natural gas. However, the thermal efficiency of the gas turbines used in these stations is low. One reason for this is that 70% of the heat of combustion of the fuel gas used by the gas turbine is lost with its exhaust gases. Hence, heat recovery from gas turbine exhaust gas would increase the cycle efficiency by decreasing the fuel gas consumed. On the other hand, gas turbine efficiency highly depends on the climatic conditions of operation. Among several well known methods of performance improvement, the use of an absorption chiller for inlet air cooling has been studied from both process and economic points of... 

An experimental investigation of unsteady boundary layer over a wind turbine blade conducted in a subsonic wind tunnel. The experiment performed at different positions along the airfoil chord. Model was oscillated with amplitude of ±5 cm. Reynolds number, based on airfoil chord, ranged 3˟105 upto 6.5˟105 and the reduced frequency ranged from 0.0055 to 0.0981. Velocity profile measured with a total pressure rake. The data were reduced via a low-pass filter. Increasing the reduced frequency, the velocity profile increases the level on turbulence fluctuation and becomes more attached to the surface.

 

Inappropriate effects of fossil fuels and conventional power generation systems on the environment have necessitated a sustainable energy system for the next decade by growing interests in renewable energy systems. The world’s most fast-growing renewable energy resource is the wind energy. The main problem of wind power is the power fluctuations at the load side caused by the variable nature of wind speed, and the main issue in case of remote locations is the long-term storage of power generated by wind turbines. Batteries can be used to store a limited amount of energy for a short time. Although new advances in this field have been achieved, most common type of batteries is hardly able to... 

The objective of the current work is to investigate the application of tandem blade rotor for possible improvements of a transonic fan. A near term application of tandem blade rotor could be either in the last stages of a high pressure compressor or in the fan section. The present research is motivated by evaluating the tandem configuration for transonic fan of high bypass ratio turbofan engines. The main idea is to achieve higher overall blade loading and at the same time lowering the flow separation tendency by shifting the boundary layer growth to the rear rotor. A computational fluid dynamics code, solving the Navier-Stokes equations based on a flexible multiple-block grid discretization... 

A Flying Electric Generator (FEG) can be a wind turbine which operates at high altitudes, where there is a continuous fast flow of air and converts wind energy to electrical power.The related field is an interdisciplinary area and is mostly related to the Aerospace Engineering and Energy Conversion. We focused on Iran, as one of the few lands in the northern hemisphere that has a high overall amount of high altitude wind energy for at least half of the year over it, according to the information of atlas of airborne wind energy in this work.So to install the FEGs in Iran, we had to find, places with a safe aerial space overhead which grant us reliable spots over country. These places found by... 

The present study was aimed at developing a model to optimize the sizing of wind turbines according to the region’s wind condition and the capital costs of each part of the turbine. The proposed model, which consists of technical aerodynamic, economic and optimization sub-models, is used to achieve maximum annual energy production by a fixed cost of a single or a number of wind turbines. A cost model has been used to determine the detailed cost of the turbine’s components. The model’s results are presented for two regions in Iran, Khaf and Ahar, and the optimized configurations for a single turbine and a wind farm have been investigated.A case study for the region- Manjil that has some... 

A new one-dimensional, time dependent aerothermodynamic mathematical model and computer simulation of the gas turbine engine has been developed and is introduced herein. This code simulates the transient and dynamic operation of the gas turbine engine bye solving conservation equations, expressed as one dimensional, time dependent Euler equations, with turbomachinery source terms. The various component models, which provide the turbomachinery source terms to Euler equations, are described. Bye incorporating both explicit and implicit equation solvers, transient simulation of the gas turbine engine can be conducted efficiently while maintaining the capability of simulating dynamic events.... 

Nowadays, because high global demand for energy has led to the extensive use of fossil fuels with numerous unintended consequences such as air pollution and greenhouse effect, research and development around optimization of energy infrastructure has become much more important. Consequently, many scientific approaches have been applied to replace fossil fuels with renewable natural energy resources. One of the renewable energy types that fewer papers have been published about it, is the enormous energy of Marine currents. The origin of this energy is mostly tidal effect, or ocean currents that are available in most of oceans and seas around the planet earth. The most important criteria for... 

Regarding the range of power in small wind turbine ,the manufacturing cost is very important to produce it feasible . so cost factors should be considered in control strategy. small wind turbine operate at lower wind speed because they are located where the energy is needed rather than where the wind is high for example in residential or rural area in lower height. In these condition wind speed are changing more because of lower height .so the maximum power point tracking algorithm should have a fast dynamic. In order to have lower number of device there are no sensor for wind or generator’s speed .only the voltage and current of different part of the system is measured.
here the aim... 

Typical thermoacoustic systems deal with the conversion of heat energy to sound energy and vice versa. Recent advances in the field of thermoacoustics have altered the working mechanism of many conventional heating and cooling devices. These systems have three highlighted advantages: first, they have simple structure, no moving parts, low cost of manufacture, and high reliability; second, by using inert gases as working fluid, they are environmentally friendly; and finally, heat driven thermoacoustic devices can be driven by low quality energy sources such as waste heat and solar energy.
The main focus of the present thesis is on the application of the thermoacoustic technology in the...