Sharif Digital Repository

To evaluate the selectivity and efficiency of solid phase microextraction (SPME) fiber coatings, synthesized by sol-gel technology, roles of precursors and coating polymers were extensively investigated. An on-line combination of capillary microextraction (CME) technique and high performance liquid chromatography (HPLC) was set up to perform the investigation. Ten different fiber coatings were synthesized in which five of them contained only the precursor and the rests were prepared using both the precursor and coating polymer. All the coatings were chemically bonded to the inner surface of copper tubes, intended to be used as the CME device and already functionalized by self-assembly... 

A functionalized poly(ionic liquid) coated magnetic nanoparticle (Fe 3O 4@PIL) catalyst was successfully synthesized by polymerization of functionalized vinylimidazolium in the presence of surface modified magnetic nanoparticles. The resulting heterogeneous catalyst is shown to be an efficient acidic catalyst for synthesis of 1,1-diacetyl from aldehydes under solvent free conditions and room temperature in high yields. Also, the catalyst shows good activity for the deprotection reaction of acylals. After completion of reaction, the catalyst was simply recovered by an external conventional magnet and recycled without significant loss in the catalytic activity. Because of the polymer layers... 

Solid-phase microextraction (SPME) is a fast, solvent-free technique, which, since its introduction in the 1990s, has been increasingly applied to sample preparation in analytical chemistry. Conventional SPME fibers are fabricated by making a physical bond between the usual silica substrate and the polymeric coatings. However, some applications are limited, as the lifetime and the stability of conventional SPME fibers cannot meet the demands of analyzing relatively non-volatile compounds with more polar moieties. There have been attempts to analyze less volatile compounds by increasing the thermal, physical and chemical stability of the fibers. In this review, we present some new... 

Novel unbreakable solid phase microextraction (SPME) fiber coatings were fabricated by electrospinning method in which the polymeric solution was converted to nanofibers using high voltages. Four different polymers, polyurethane (PU), polycarbonate (PC), polyamide (PA) and polyvinyl chloride (PVC) were prepared as the fiber coatings on thin stainless steel wires. The extraction efficiencies of new coatings were investigated by headspace solid-phase microextraction (HS-SPME) of some environmentally important chlorobenzenes from aqueous samples followed by gas chromatography-mass spectrometry (GC-MS) analysis. Among them, PU showed a prominent efficiency. Effects of coating time and polymer... 

It is well known that the oil recovery is affected by wettability of porous medium; however, the role of nanoparticles on wettability alteration of medium surfaces has remained a topic of debate in the literature. Furthermore, there is a little information of the way dispersed silica nanoparticles affect the oil recovery efficiency during polymer flooding, especially, when heavy oil is used. In this study, a series of injection experiments were performed in a five-spot glass micromodel after saturation with the heavy oil. Polyacrylamide solution and dispersed silica nanoparticles in polyacrylamide (DSNP) solution were used as injected fluids. The oil recovery as well as fluid distribution in... 

This review is mostly focused on the recently emerged methodologies for preparing the appropriate extracting media with enhanced capacity, stability and selectivity, which could be used in capillary microextraction (CME). We particularly consider conductive polymers, sol-gel-based materials, monolithic coatings, molecularly-imprinted polymers and xerogels. Moreover, we discuss recent advances in configuration of CME, array capillaries and unbreakable substrates  

In this article, a novel energy-based lifetime prediction model has been presented for uncoated and coated aluminum alloys, subjected to thermal and mechanical fatigue loadings. For this objective, isothermal and thermo-mechanical fatigue tests were performed on the A356.0 alloy, with and without thermal barrier coating systems. This model, which was based on the plastic strain energy, had three correction factors including temperature, strain and mean stress effects. The predicted lifetime showed a proper agreement with experimental data. By the present model, higher accuracy was obtained in comparison to other existed approaches. Besides, the present model had lower number of material... 

Propagation of P-wave in an unbounded elastic polymer medium which contains a set of nested concentric spherical piezoelectric inhomogeneities is formulated. The polymer matrix is made of Epoxy and is isotropic; each phase of the inhomogeneity is made of a different piezoelectric material and is radially polarized and has spherical isotropy. Note that the individual phases are homogeneous, and all interfaces are perfectly bonded. The scattered displacement and electric potentials in the matrix are expressed in terms of spherical wave vector functions and Legendre functions, respectively. The transmitted displacement and electric potentials within each phase of the piezoelectric particle are... 

The fracture toughness and deformation mechanism of PP/CaCO3 (15 wt.%) composites were studied and related to load-bearing capacity of the particles. To alter the load-bearing capacity of the particles, different particle sizes (0.07-7 μm) with or without stearic acid coating were incorporated. The fracture toughness of the composites was determined using J-Integral method and the deformation mechanism was studied by transmission optical microscopy of the crack tip damage zone. It was observed that the load-bearing capacity of the particles decreased by reduction of particle size and application of coating. A linear relationship between normalized fracture toughness and inverse of... 

A developed route to form TiO2 self cleaning coatings on polycarbonate substrates is reported. TiO2 coatings on plastics may find widespread application in auto and construction industries if possess desired photocatalytic and mechanical properties. A chemical surface treatment method was used to create hydrophilic groups on the surface. X-ray photoelectron spectroscopy showed the treatment led to the oxidation of surface groups. TiO2 deposition was based on wet coating using an anatase sol of TiO2 nanoparticles of 30 nm size. The sol was synthesized using a sol-gel route. A pre-coat of peroxotitanium complex was employed to improve adhesion and inhibit the substrate degradation. The coating... 

This work presents the synthesis of nanostructured hollow polyaniline (PANI) capsules and their application for encapsulation of corrosion inhibitor 2-Mercaptobenzothiazole (MBT). The pH-triggered release of MBT from the capsules was evidenced using UV–vis and Surface Enhanced Raman Spectroscopy (SERS). Incorporation of MBT loaded PANI capsules into epoxy ester coating on AA2024-T3 resulted in a protective system with self-healing ability confirmed by Electrochemical Impedance Spectroscopy (EIS) and Scanning Vibrating Electrode Technique (SVET). The results showed that the incorporation of MBT-loaded PANI capsules into the coating has significantly improved its corrosion protection... 

Copper supported on polymer-coated magnetic nanoparticles was designed and synthesized as a separable heterogeneous catalyst. The catalyst was fully characterized using several techniques such as Fourier transform infrared and energy-dispersive X-ray spectroscopies, scanning and transmission electron microscopies, X-ray diffraction, vibrating sample magnetometry, thermogravimetric analysis and inductively coupled plasma atomic emission spectrometry. All results showed that copper was successfully supported on the polymer-coated magnetic nanoparticles. Also, results showed that the synthesized material can be used as an efficient catalyst for the preparation of a series of 1,4-disubstituted... 

In order to improve the catalytic activity and durability of proton-exchange-membrane-fuel-cells (PEMFCs), Nafion-free Pt-based catalyst using the superacid-doped polymer coated multiwall carbon nanotubes (MWCNTs) was investigated. The modification and nano polymerization of MWCNTs were developed by polyvinylpyrrolidone (PVP). The following observations were made in the presence of polymer: better dispersion of MWCNTs, higher thermal stability of MWCNT/PVP than that of pristine MWCNT up to 450 °C as tested by thermal gravimetric analysis (TGA), homogeneous distribution of Pt without agglomeration as observed by transmission electron microscope (TEM), and not too much difference in Pt loading... 

Novel bilayer coated mesoporous silica nanoparticle (MCM-41) based on pH sensitive poly(acrylic acid-co-itaconic acid) and human serum albumin (HSA) was designed for controlled delivery of gemcitabine (anticancer drug) to cancer cells. The shell around the mesoporous silica has bilayer structure. Poly(acrylic acid-co-itaconic acid) was used as pH-sensitive inner shell and human serum albumin, HSA, was used as outer shell. The core-shell structure was formed due to electrostatic interaction between ammonium groups of modified MCM-41 and carboxylate groups of copolymer. Also, the albumin layer was wrapped around the copolymer coated nanoparticle by electrostatic interaction between ammonium... 

For the efficient removal of some anionic dyes, a novel adsorbent was developed. The adsorbent was prepared by coating a synthetic polymer on magnetite nanosphere surface as a magnetic carrier. The synthesized nano-adsorbent was fully characterized using Fourier transform infrared spectroscopy (FT-IR), vibrating sample magnetometer, X-ray diffractometer, scanning electron microscope, and transmission electronic microscopy measurements. The synthesized nano-adsorbent showed high adsorption capacity towards removal of some anionic dyes (221.4, 201.6, and 135.3 mg g-1 for reactive red 195, reactive yellow 145, and reactive blue 19 dye, respectively) from aqueous samples. The dye adsorption was... 

Copper supported on polymer-coated magnetic nanoparticles was designed and synthesized as a separable heterogeneous catalyst. The catalyst was fully characterized using several techniques such as Fourier transform infrared and energy-dispersive X-ray spectroscopies, scanning and transmission electron microscopies, X-ray diffraction, vibrating sample magnetometry, thermogravimetric analysis and inductively coupled plasma atomic emission spectrometry. All results showed that copper was successfully supported on the polymer-coated magnetic nanoparticles. Also, results showed that the synthesized material can be used as an efficient catalyst for the preparation of a series of 1,4-disubstituted... 

A superhydrophobic nanocomposite coating was fabricated using a simple procedure. The nanocomposite is composed of an acrylic copolymer and modified silica nanoparticles. The acrylic copolymer was prepared by free radical copolymerization of methyl methacrylate and dodeycl methacrylate monomers. Silica nanoparticles were synthesized and modified with an alkyl silane reagent, hexadecyltrimethoxysilane. A mixture of acrylic copolymer and modified silica nanoparticles, dispersed in dichloromethane, was then sprayed on glass and filter paper surface. Chemical composition and structure of the coatings were investigated by FTIR, FESEM, AFM, 1H-NMR and GPC. The wettability of the prepared coating... 

Breast Cancer (BRCA) is the most common threat in women worldwide. Increasing death rate of diagnosed cases is the main leading cause of designing specific genosensors for BRCA − related cancer detection. In the present study, an ultrasensitive label − free electrochemical DNA (E − DNA) sensor based on conducting polymer/reduced graphene − oxide platform has been developed for the detection of BRCA1 gene. An electrochemical method was applied as a simple and controllable technique for the electrochemical reduction of graphene oxide and also, electro − polymerization of pyrrole − 3 − carboxylic acid monomer. The results of the present work show that the polymer − coated reduced graphene −... 

This paper presents the results of diagonal compression tests conducted on a series of un-reinforced and reinforced masonry specimens. Reinforced specimens were strengthened by using three types of mortar coating (with and without inner reinforcement), mesh reinforcement, and PP-band reinforcement. In particular, four different reinforcement methods with mortar coating (bare mortar coating, coating with steel mesh, coating with polymer reinforcement, and coating with GFRP mesh reinforcement), three different mesh-only reinforcement (steel mesh, polymer mesh with larger grids, and polymer mesh with smaller grids), and 2 different arrangements of PP-bands (4 × 4 and 6 × 6) were tested. Also,... 

This study reports the importance of physicochemical characteristics of the core-shell structured polymer-coated Fe3O4 cluster@SiO2 nanocomposite particles for designing the biocatalysts used for transesterification of soybean oil. To demonstrate this issue, two different types of polymer molecules such as polyethylenimine (PEI) and polyacrylic acid (PAA) each with two different molecular weights are employed. The highest fatty acid methyl esters (FAMEs) synthesis yield values are achieved by the lipases immobilized onto the low- and high-molecular-weight PEI-coated particles as compared to those of the low- and high-molecular-weight PAA-coated particles (i.e., ∼64.8% and ∼73.1% versus...