Sharif Digital Repository

Among the equipment used in supermarkets, refrigeration systems should be the focus of energy efficiency initiatives; Because they are the biggest consumers of energy and refrigerant with significant maintenance costs. Fault detection and diagnosis (FDD) can provide considerable potential for energy savings as well as reduced maintenance costs. Although there have been numerous investigations of FDD for HVAC systems, there has been very little research on the application of FDD for supermarket refrigeration systems. Therefore, this thesis focuses on the application of FDD to these systems and helps to fill these research gaps. The studied system is a commercial refrigerator system on a... 

In general, the output power of the gas turbines decreases as the ambient temperature increases. One of the ways to deal with such a performance loss is to use a wet compression system, which reduces the air temperature rise throughout the compressor. In this system, the water droplets are injected into the compressor inlet and evaporated throughout the stages. As a result, the work of the compressor decreases, and the power and efficiency of the whole engine increase. Most of the researchers in this field have tried to develop mathematical models to investigate the effects of this system on compressor and gas turbine performance in steady-state conditions. However, it is necessary to... 

In recent years, there has been the extensive researches on energy and water efficiency due to the increasing stress on these resources. Therefore, the water-energy nexus in large industries, especially power plants, has become very important. In the present study, the water and energy nexus has been analyzed using energy analysis tools, exergy, economic and environmental in a combined cycle power plant. The nexus are observed in the boiler blow-downs, leakage of steam traps, cooling of the air entering the compressor and injection of steam into the combustion chamber, which have been studied in different scenarios to improve water and energy consumption and reduce environmental impact. In... 

Injecting several droplets with a known size distribution function in the hot gas environment makes droplets smaller because of evaporation or reaction. Droplets lifetime specification is important in vapor-liquid interactive processes such as chemical or process industries. In previous works, different approximate semi-empirical methods are developed to specify droplets lifetime without considering their size distribution. In this work, governing equations is studiedconsidering a size distribution function for droplets. There is not any analytical method for solving this set of equations, so numerical methods using CFD packages such as Fluent, are applicable in these cases. In this study,... 

The aim of the work presented in this thesis is deal with some of the aspects in the FEM analysis of sandwich panels containing holes which comprised with foam core. It is a new topic in this field; so the activities that have been done about this case are poor with respect to its performances in engineering. The main emphasis is placed on the treatment of the foam core since the core often is the weakest part of the sandwich and therefore in many ways governs the capacity and lifetime of the whole sandwich structure. Because of increasing application including construction, aircraft and transportation, marine and etc., different load conditions are considered for the analysis and... 

Two-phase flows are widely used in petrochemical industry, chemical processes, boilers, nuclear reactors, cooling systems and air conditioning equipment. Since the problem of earth’s ozone layer and global warming, the analysis of flow characteristics in evaporators are necessary to improve performance of refrigerating systems and saving the environment. Most of the researchers have been studied the evaporation of two phase flow refrigerant through experimental studies and numerical analysis has less attention in the literature. In this Thesis, a mathematical model based on the two-phase separated flow model is developed to simulate the evaporation of pure refrigerant under constant heat... 

This study aims to estimate the emission rate of Volatile Organic Components (VOCs) and hazardous air pollutants from the surface of evaporation ponds in oil and gas upstream industries. With respect to the irrecoverable consequences of such emissions, the emission of air pollutants in the oil and gas upstream industries are alarming. Hence, estimation of the pollutants’ emission and surface pollution monitoring are needed for controlling and decreasing of air pollutants in oil and gas upstream industries and also presenting and performing suitable and efficient solutions. The studied ponds in this research include 4 ponds in the oil and gas upstream industries which have been used for... 

In this study the transport and deposition of pharmaceutical particles delivered by a commercial metered dose inhaler (MDI) is investigated in a combination of human upper airways, inhaler, and spacer. The emphasis of the present work is on the effects of evaporation of ethanol from particles, inlet momentum of particles, and use of spacer on their transport and deposition phenomena. The pharmaceutical particles are typically delivered with high initial momentum to human upper airways. It is believed that this initial momentum is responsible for increased undesirable deposition of particles in upper airways, especially in case of particles larger than 1 micrometer in diameter. In the present... 

Casting process with foam is a relatively new process which because of having multiple benefits (like elimination of muscle and segregation line, high dimensional precision and using sand without using glue) in recent years has been considered. Considering that during pouring, melt replaces with sand surrounded foam, successfulness of this method depends on complete elimination of foam model during Pouring for preventing formation of some defects like carbon defects in cast irons, or cold work and porosity in aluminum alloys. Parameters like Pouring temperature, alloy type, foam type, density of foam model, type of gating system, and some other parameters are affecting the way of filling of... 

Reducing water evaporation is one of the ways to overcome the low precipitation and drought conditions in water reservoirs. For this purpose, extensive studies have been investigated on physical and chemical coatings on lakes and reservoirs. Physical methods often involve the use of floating covers on the water surface to block evaporation by shading, most of which are only suitable for reservoirs with surface areas smaller than 5 hectares. In chemical methods, the evaporation can be decreased by nanomaterial coating, usually, containing long-chain molecules, which by spraying them on the surface, molecular monolayers are formed. In this study, the effect of nanometer coatings on the surface... 

This study develops a new framework for the assessment of land subsidence occurrence rate. The proposed framework considers the combined effects of saturated and unsaturated soil behavior. Accordingly, the biot consolidation theory was used for investigating subsidence in the saturated zone while the soil shrinkage curve, i.e., the void ratio-suction curve, was used in the determination of unsaturated zone subsidence. Specifically, groundwater decline and land climate change were used as the main contributing factor in investigating the land subsidence in the saturated and unsaturated zone, respectively. The approach presented in this study is based on using numerical modeling in PLAXIS 2D... 

Uranium conversion process is one of the most important stages in nuclear fuel cycle. The Uranium Conversion Facilities (UFC) of Iran is located in Isfahan. In this plant, the Yellowcake (impure uranium oxide, U3O8) is converted to Uranium hexa-fluoride, UF6. During the process, considerable amounts of uranium-containing liquid waste are generated. This liquid waste was collected in evaporation pools inside the UCF Plant. In the course of time, a thick layer of precipitated salt form in bottom of the pools which are collected and stored in drums inside a building. This solid waste contains uranium at concentration levels much higher than that permitted for land disposal of the waste.... 

Functional design of coating system for the primary mirror of the Iranian National Observatory (INO) is done. This telescope has a 3.4 m primary mirror in diameter, made of Zerodur from Schott. Although similar coating systems are in use since years ago, this is the first attempt to design a system for such a large surface case in Iran. Systematic approach led us first to clarify and identifying the design requirements. Lower limit of 80% for reflectance on all wavelength range from 325-1000 nm, thickness of 100 nm with un-uniformity of 5 nm, adhesion enough to pass the selotape test and surface roughness of less than 8 nm. Study of the available methods for coating and selection of the best... 

One of the important issues that increasing development of electronic systems has caused is how to transfer the generated heat out of the system. Heat pipes can transfer large amount of heat because of using latent heat of evaporation and condensation. In micro scales using micro heat pipes is popular that in this instrument liquid returns to evaporator by means of surface tension force. So numerical solution is essential for verifying experimental results and increasing performance of this instrument. In this research has been planned to develop a comprehensive model for numerical solution of flow and heat transfer in micro heat pipes. For this reason surface evaporation and …,... 

In this thesis, using superstructure concept, a method is presented to synthesize of new structures for thermal desalination processes along with their structural and operational optimization. The proposed superstructure is capable of producing various common (feed forward, backward, parallel cross feed) and non-common structures in evaporators, as well as in combination with flash stages and thermal vapor compressor. By using the GA (Genetic algorithm), the superstructure has been optimized to identify the optimal structures in both Iranian and international economic scales. Also comparisons were made between conventional structures at optimum state, to suggest superior structures at... 

This study tries to introduce chemical coatings to reducing evaporation from Lake Urmia(LU). In LU, average annual evaporation is estimated at more than 1,000 mm, more than 80% of evaporation occurring in the warmer months of the year. Therefore, by reducing water evaporation, especially in the warmer months of the year, the most crucial factor in water outflow from LU can be reduced.At first, on the scale of class A evaporation pan in Tehran, three kinds of chemical coatings constituted stearic acid, jojoba oil, and fatty alcohols of style and stearyl to reduce evaporation from the LU is investigated. Then the best coating that includes combine of style and stearyl alcohols with stearic... 

Since physical variables are almost dependent, uncertain and have significant time and spatial changes, nature of hydrological and environmental systems is so complicated, nonlinear and dynamic. Many models have been developed for studying and analyzing various phenomena in these systems. Recently data mining approaches have been used as new methods for modeling of complicated engineering systems. In this study, performance of several data mining tools in analyzing two phenomena in water quality management have been evaluated. These algorithms are Multilayer Perceptron Neural Network (MLP), Radial Basis Function Neural Network (RBFN), Support Vector Machines (SVMs) in the field of Artificial... 

One of the novel methods of stabilization of nuclear waste is the use of vitrification technology. In order to stabilize high level wastes (HLLW) in glass, it is required that the elements are in their oxide form. Therefore, it is necessary to evaporate the waste and turn it into a solid form so that the elements can be converted into oxide form in the calcination furnace. Hence, one of the challenges of stabilization is the optimization of evaporation and calcination conditions. In this research, the parameters affecting evaporation were first investigated. Using laboratory measurements of application: temperature (110 to 180 °C), presence of nitric acid (0.5 to 4 mol/L), ratio of zirconium... 

The present thesis aimed to study a novel heat pump integrated humidification-dehumidification (HDH-HP) desalination system. A theoretical outline was proposed for the first time to examine the design and off-design performance of HDH-HP cycles via the compressor characteristics method. In this regard, the variations in heat pump performance were modeled in different operating conditions for a fixed-size system. To fabricate a compact HDH-HP system, an evaporative condenser was designed and used instead of a separate humidifier, heater, and air/water-cooled condensers find in previous HDH-HP systems. Meanwhile, the air dehumidification process in this work directly occurred inside the heat... 

Optimizing the energy consumption of air conditioning systems has gained great importance in recent years. In addition, maintaining thermal comfort and air quality in buildings is important. The multi-evaporator air conditioning system, which is a direct expansion system, shows the complex and distributed structure of air conditioning systems due to the thermal connection between zones and its large scale. The modeling of these systems is associated with uncertainties. Therefore, designing a suitable control structure for multi-zone systems is very important to achieve optimal energy consumption and maintain comfort conditions in the presence of uncertainty. Model predictive control has been...