Sharif Digital Repository

Gas-oil relative permeability is essential for performance predictions of reservoirs with solutions for gas drive, gas cap expansion, or gas injection. The nature of flow in reservoir is determined by the interplay of relative permeability and viscous, gravity, and capillary forces. Displacement experiments of the gas-oil system are performed on long core scale models by varying the petrophysical properties and flow conditions. Experiments are conducted in situations where capillary, gravity, and viscous forces are comparable. The effect of destabilized front velocity on relative permeability and residual saturation is investigated. The results indicate that the relative permeability varies... 

This paper investigates numerical simulation of one-dimensional homogeneous adiabatic gas-liquid two-phase flow in a rectangular microchannel with one boundary porous wall under the assumption of hydrophobic condition. Gas enters the microchannel with a uniform velocity and liquid is injected through the porous side wall. The present approach is to simulate water injection effects and developing mechanism of two-phase flow. The modeling and solution of the conservation equations provide pressure drop, vapor quality, void fraction and tow-phase mixture velocity for different water injection rates. The results show that velocity and pressure drop significantly perturbed when the water... 

Most of the reservoirs in Iran and also around the world are in the middle of their production life and have passed their natural production period. Therefore, they should be a candidate for immiscible injection, e.g., water injection for secondary recovery, and/or miscible injection, like solvent injection for tertiary recovery. Also, it should be pointed out that most of the Iranian reservoirs are carbonate reservoirs. This type of reservoir is fractured and heterogenic. Heterogeneity causes an earlier breakthrough and immiscible injection causes an unstable front, which leads to a lower recovery. This article presents the modified equation of Buckley-Leverett and fractional flow... 

Smart water flooding as a developing technique utilizes modified water chemistry in terms of salinity and composition to prepare the best-suited brine composition for a specific brine/oil/rock system to obtain higher oil recovery efficiency. Huge amount of unrecovered oil is expected to be remained in carbonate reservoirs; however, few research works on incremental oil recovery during smart water injection in carbonate cores at reservoir condition are reported. Several core flooding tests using one of the Iranian carbonate reservoir rock are conducted to check the effectiveness of smart water injection for more oil recovery efficiency. The results reaffirm the positive effect of sulfate ions... 

The process of asphaltene precipitation has a substantial effect on oil flow during primary oil production and enhanced oil recovery processes in the petroleum industry. In this work, a modified scaling model based on the PVT properties of bottom hole live oil including resin to asphaltene ratio, onset pressure, bubble point pressure, reservoir temperature, asphaltene content of bottom hole live oil and gas to oil ratio has been proposed to account for asphaltene precipitation under pressure depletion/gas injection conditions and the proposed model was verified using experimental data obtained in this work and also with those reported in the literature. In the proposed scaling model the... 

In reservoirs that have been water flooded or gas injected, it is still a significant amount of the remaining oil. Water alternative gas injection is a tertiary oil recovery method which was used for the first time in Canada for recovering remained oil in place of reservoir. The pore-scale mechanisms of this process are not fully understood yet. Such knowledge is essential for accurate modelling of reservoir. In this study various experiments on the WAG process is carried out by means of high pressure glass type micromodel instrument. The micromodel apparatus in this experiment was capable to operate at pressures up to 3500 Psi and temperatures up to 85°C which is similar to conventional... 

There is currently a significant focus on using boundary layer control (BLC) approach for controlling the flow around bodies, especially the foil sections. In marine engineering this is done with the hope of increasing the lift - to - drag ratio and efficiency of the hydrofoils. In this paper, effects of the method on hydrodynamic characteristics and tip vortex formation of a hydrofoil are studied. Steady water injection at the tip of the hydrofoil is simulated in different conditions by using ANSYS-CFX commercial software. Validity of the proposed simulations is verified by comparing the obtained results against available experimental data. Effects of the injection on the lift, drag, and... 

Capillary imbibition is an important recovery mechanism in naturally fractured reservoirs when water-filled fractures surround water-wet matrix blocks. A large amount of studies of imbibition process is simply total or partial immersion of nonwetting phase saturated rock in aqueous wetting phase. However, water advance in fractures during water flooding or water encroachment from an active aquifer introduces time dependent boundary conditions where invariant exposure of rock surface to water is not representative. In this work, a laboratory simulated matrix-fracture system was used to investigate different aspects of imbibition in the presence of fracture fluid flow (namely dynamic... 

In this paper, different injectivity scenarios were experimentally investigated in a coreflooding system to observe the efficiency of each method in laboratory conditions. Surfactant flooding, CO2 injection, carbonated water injection (CWI), active carbonated water injection (ACWI), after water flooding were investigated through the coreflooding system. First, it is necessary to optimize the surfactant concentration and then use it in ACWI injection. To do this, linear alkylbenzene sulfonic acid (LABSA) was used as a cationic surfactant at different concentrations. It was observed that 0.6 PV concentration of LABSA had an optimum result as increasing the surfactant concentration would not be... 

In this paper, a computational technique is presented for the isothermal and non-isothermal water injection into naturally fractured oil reservoirs. A remarkable number of naturally fractured reservoirs contain relatively heavy oils that could not be extracted economically; hence, the thermal recovery methods are extensively used for such reservoirs. In this study, the effectiveness of hot water injection over cold (isothermal) water injection in oil production is quantified. The influence of long and short fractures and their alignments on oil recovery are discussed. To this end, a 2D model for two-phase fluid flow and heat transfer is presented. The medium is assumed to be partially...