Sharif Digital Repository

Batch adsorption experiments were carried out for the removal of malachite green (MG) cationic dye from aqueous solution using novel hydrogel nanocomposite that was prepared by graft copolymerization of acrylic acid (AA) onto kappa-carrageenan (κC) biopolymer in the presence of a crosslinking agent, a free radical initiator and aminosilica-functionalized TiO2 nanoparticles (κC-g-PAA/TiO2-NH2). The factors influencing adsorption capacity of the adsorbents such as initial pH value (pH0) of the dye solutions, TiO2-NH2 content (wt%), initial concentration of the dye, amount of adsorbents, and temperature were investigated. The adsorption capacity of hydrogel nanocomposite for MG was compared... 

The suspension of titania nanoparticles in different alcohols (methanol, ethanol, and butanol) was prepared and triethanolamine (TEA) was used as a dispersant. The suspensions were characterized by different tests such as sedimentation, zeta potential, and Fourier transform infrared spectroscopy. The electrophoretic deposition (EPD) was performed at various voltages and times. EPD from butanolic suspension (0.8 g/L TEA) showed the slowest kinetics, because of the low electrophoretic mobility of titania nanoparticles in it (2.40 × 10-5 cm2·(V·s)-1). Also, it was observed that at low voltages (5, 10, and 20 V), the EPD kinetics from methanolic suspension (0 g/L TEA) was the fastest; however,... 

A novel and simple photoelectrochemical (PEC) sensor to detect Cr(VI) based on screen-printed TiO2 modified with gold nanoparticles is presented. The proposed PEC sensor showed a very low detection limit (S/N = 3) of 0.004 μM, over a wide linear concentration range from 0.01 μM to 100 μM with a high sensitivity of 11.88 μA.μM-1 Cr(VI). Results also indicated good anti-interference and superb recovery in natural media application for Cr(VI) sensing  

Two different hydroxyapatite based composites reinforced by oxide ceramic (20 wt%) nano crystals were synthesized by high-energy ball milling and sintered by pressure less technique. Alumina and titania nanoparticles as secondary phases improved densification and mechanical behavior of apatite and postponed its decomposition to the tricalcium phosphate (TCP) phases at elevated temperatures. Increasing the relative density of apatite using nano reinforcements leads to enhance the bending strength by more than 40% and 27% (as compared to the pure HA) and increase the hardness from 2.52 to 5.12 (Al2O3 composite) and 4.21 (TiO2 addition) GPa, respectively. Transmission electron microscopy (TEM),... 

Hydrophobic titania nanoparticles were synthesized by a novel in situ sol-gel method and applied in a single drop liquid-liquid extraction column to enhance the overall dispersed-phase mass transfer coefficient (Kod). The chemical system of toluene, acetic acid and water was used, and the direction of solute (acetic acid) mass transfer was from dispersed phase, including: toluene and acetic acid to the continuous phase of water. For such system, much of the mass transfer resistance exists in the dispersed phase, which is nonpolar organic liquid. Hence, modified titania nanoparticles (MTNP's), prepared by sol-gel route, in five different concentrations of 0.001–0.005 wt.% were added in the... 

Titania nanoparticles with high photocatalytic activity were prepared from titanium alkoxide dissolved in alcohol and water under acidic conditions. The effects of the key parameters including (alkoxide/water) ratio, (alkoxide/alcohol) ratio, precursor type, solvent type, type and concentration of stabilizer, calcination temperature, presence of methylcellulose (MC) and hydrothermal treatment were studied. The optimal conditions were obtained through an experimental design technique. This technique is also used to find the main factors influencing the degradation of methylene blue (MB) and mass percent of anatase phase. The powders characteristics were investigated by XRD and... 

In this research, an attempt was made to investigate the potential of nanophotocatalysts for treatment of hazardous wastewater streams. Titanium dioxide nanoparticles (as photocatalyst) were immobilized on a porous and low-density support called "perlite" using a very simple and inexpensive method. TiO2-coated perlite granules were used in a "Floating-bed photoreactor" to study the photocatalytic purification process of a typical wastewater polluted by furfural. The effects of initial concentration, catalyst mass/solution volume ratio, oxidant molar flow, residence time, and light intensity on process removal efficiency, and kinetics of the reactions were studied. SEM analyses showed a...