Sharif Digital Repository

In this study, titanium dioxide nano powders were electrophoretically deposited on the stainless steel in Isopropanol and Triethanolamine as a solvent and dispersant, respectively. The effects of deposition parameters including deposition voltage (5 to 20 V) and deposition time (5 to 60 s) on the microstructure and surface topography were examined by scanning electron microscope (SEM) and scanning probe microscope (SPM), respectively. In addition, the effects of these deposition parameters on packing density were investigated. This research revealed that substrate surface is fully covered with increasing deposition voltage and deposition time. Therefore packing density of deposited films is... 

The spatial scaling law and intermittency of the V2O5 surface roughness has been investigated by atomic force microscopy. The intermittency of the height fluctuations has been checked by two different methods, first, by measuring the scaling exponent of the qth moment of height-difference fluctuations i.e. Cq = <|h(x1) - h(x2)|q>, and second, by defining the generating function Z(q, N) and generalized multi-fractal dimension Dq. These methods predict that there is no intermittency in the height fluctuations. The observed roughness and dynamical exponents can be explained by numerical simulation on the basis of the forced Kuramoto-Sivashinsky equation  

The effect of etching time scale of glass surface on its statistical properties has been studied using atomic force microscopy technique. We have characterized the complexity of the height fluctuation of an etched surface by the stochastic parameters such as intermittency exponents, roughness, roughness exponents, drift and diffusion coefficients and found their widths in terms of the etching time. © 2006 Elsevier B.V. All rights reserved  

The accurate measurement of surface roughness is essential in ensuring the desired quality of machined parts. The most common method of measuring the surface roughness of machined parts is using a surface profile-meter with a contact stylus, which can provide direct measurements of surface profiles. This method has its own disadvantageous such as workpiece surface damage due to mechanical contact between the stylus and the surface, In this paper we proposed a eontactless method using image processing and artificial neural network as a pattern classifier. Having trained the network for any specific workpiece with 10 sample patterns, the system would learn how to approximate the actual surface... 

Effect of different conditions on shear behaviour of rock has been investigated by various researchers. As known, in larger scale the continuity of the rock material is interrupted by separated planes such as bedding planes, faults, shear zones, closure and the behaviour converts to be inelastic and anisotropic. Generally, discontinuities appear repeatedly in more than one preferential direction, creating a three dimensional structure, reducing its stiffness and shear strength as mechanical effects and increasing its transport velocity associated with discontinuity flow as hydraulic effects. They also make rock behavior more complex and different compared to the behavior of soil. According... 

Superalloys have a poor machinability and are often drilled using Electro Discharge Machining (EDM) methods. However EDM is a time-consuming process and has low surface integrity. Ultrasonic Assisted Drilling (UAD) technology is a modern method of drilling such materials. Although this method has very high capabilities, it has not been introduced widely to industry. In this study a special horn is designed and used to apply both rotation and vibration to drill bits. It can transfer power with high efficiency and has the capability to change tools easily. The setup is used to conduct deep drilling tests on Inconel 738LC with depth-to-diameter ratio of 10. The effect of ultrasonic vibration... 

In this work, spin transport in corrugated armchair graphene nanoribbons (AGNRs) is studied. We survey combined effects of spin-orbit interaction and surface roughness, employing the non-equilibrium Green's function formalism and multi-orbitals tight-binding model. Rough substrate surfaces have been statistically generated and the hopping parameters are modulated based on the bending and distance of corrugated carbon atoms. The effects of surface roughness parameters, such as roughness amplitude and correlation length, on spin transport in AGNRs are studied. The increase of surface roughness amplitude results in the coupling of σ and π bands in neighboring atoms, leading to larger spin... 

Background: Optical coherence tomography (OCT) is an imaging method that provides real time in situ visualization of human tissue at sub-micrometer resolution. Prior research shows OCT is suitable for imaging the epidermis. Method: In this study, we utilized OCT images to noninvasively measure the quantitative effect of a specialized antiaging product compared with a petrolatum control in a split-face trial. The images acquired with OCT were analyzed to determine the average surface roughness, Ra, and surface roughness depth, Rz, of the imaged skin. These values were measured over the duration of a 28-day trial. Results: The petrolatum treated skin showed a 2.1% and 2.9% decrease in Ra and... 

In this work, we have studied single-texture formation of CoSi2 layer in heat-treated Co/Ta0.7W0.3/Si(100) structure. Moreover, self-encapsulation process of the CoSi2 layer and surface roughness of the encapsulated layer, as a contact layer, has been examined. A direct current magnetron co-sputtering technique was employed to deposit a 10 nm Ta0.7W0.3 alloy intermediate layer. After growth of the layer on the Si substrate, a 25 nm Co layer was deposited using thermal evaporation method. Post-annealing process of the films was treated in an N2(80%) + H2(20%) ambient in a temperature range from 400 to 1000 °C for 60 min. X-ray diffraction analysis showed that a single-texture CoSi2 layer with... 

An extensive experimental investigation to study the effect of the reduced frequency and surface grit roughness on an airfoil oscillating in plunging motion has been conducted. The application of surface grit roughness simulates surface irregularities that occur on the wind turbine blades. Data were taken at a Reynolds number of 0.42*10* and at a range of reduced frequencies, k=0.03-0.1. Tests were conducted at plunging amplitudes of ±10cm and ±15cm and at mean angles of attack of 0°, 10° and 18°. It was found that the width of the hysteresis loop, position of the figure-8 shape, slope of the lift coefficient curve and maximum lift force have been influenced by both oscillation frequency and... 

A series of low speed wind tunnel tests on a section of a 660 Kw wind turbine blade which is under constructer were conducted to examine the effects of distributed surface contamination on its performance characteristics. At first model was tested in the clean condition and after that it was tested with tree different types of roughness. The data shows that this particular airfoil is very sensitive to the applied surface roughness. For the contaminated model the roughness, 0.5mm height was distributed over the entire upper surface of the airfoil such that the distribution pattern was denser in the vicinity of the leading edge and thinner in the trailing edge area. Statistical data show that... 

In present paper the theory of the micropolar fluid based on a Cosserat continuum model has been applied for analysis of Couette flow and turbulent flow through rough pipes. The obtained results for the velocity field have been compared with known results from experiments done by Reichardt at Max Plank institute for fluids in Gottingen [1,2] and analytical solution of the problem from Gradient theory by alizadeh[3] for couette problem and with known results from experiments done by Nikuradse (1932).the boundary condition used here was the no slip one and Trostel's slip boundary condition[4].a good agreement between experimental results and the results of the problem for Reynolds near 18000... 

A series of experiments were conducted on an oscillating airfoil in subsonic flow. The model was oscillated in two types of motions, pitch and plunge, at different velocities, and reduced frequencies. In addition, steady data were acquired and examined to furnish a baseline for analysis and comparison. The imposed variables of the experiment were reduced frequency, mean incident angle, amplitude of motion, and free stream velocity as well as the surface grit roughness. The unsteady aerodynamic loads were calculated using surface pressure measurements, 64 ports, along the chord for both upper and lower surfaces of the model. Particular emphases were placed on the effects of different type of... 

The impact strength of poly(methyl methacrylate)/caibon (long) fibre composites for denture prosthesis applications was improved by fibre surface treatment. The carbon fibre surfaces were modified by Nd:YAG laser irradiation at 1064 nm wavelength. Laser light intensity was adjusted at 100 mj per pulse that only changed the fibre surface roughness and did not lead to fibre rupture, as verified by scanning electron microscopy. Increased surface roughness of the fibres improved the adhesion of poly(methyl methacrylate) to the fibre surface. Adhesion between the fibres and poly(methyl methacrylate) was evaluated by a tear-off method and by scanning electron microscopy. The results also suggest... 

A series of low speed wind tunnel tests on a section of a 660 Kw wind turbine blade were conducted to examine the effects of distributed surface contamination on its performance. The airfoil was a section of a wind turbine blade under construction. The performance of the section was measured in the following conditions: 1. Clean airfoil 2. Two types of zigzag roughness 3. Strip tape 4. Distributed contamination roughness Our preliminary data shows that the airfoil is very sensitive to the applied surface roughness. For the contamination model the roughness, 0.5mm height, is distributed over the entire upper surface of the airfoil. By putting the contamination roughness on the airfoil the... 

The wear and friction properties of G-Cu (Sn) composite coatings containing different amounts of graphite particles were examined. The presence of graphite particles improved antifriction properties of composite coatings. The effects of graphite percent in composite coating, tin content of matrix, load, speed and distance on the coefficient of friction and wear resistance of bronze-graphite composite coatings were studied. The results of the present studies revealed that hardness, wear resistance, coefficient of friction are dependent on volume percentage of graphite in composite coating. It was shown that the composite coating containing approximately 5.4 (vol.%) graphite and matrix with...