Sharif Digital Repository

In a shell and tube heat exchanger, the failure of tube-to-tubesheet welds results in high-pressure water jet which erodes the refractory in front of the tubesheet. Finite element method was employed to simulate the welding process and post weld heat treatment (PWHT) to find the factors affecting the failure in tube-to-tubesheet weldments. Residual stresses in two different geometries of tube-to-tubesheet weldment were calculated through uncoupled thermal-structural analysis. The results showed that the values of residual stresses are higher in heat exchanger of site 1 than site 2 due to more weld passes and geometry of connection. Also, the maximum stress in site 1 occurs at the shellside... 

In a shell and tube heat exchanger, the failure of tube-to-tubesheet welds results in high-pressure water jet which erodes the refractory in front of the tubesheet. Finite element method was employed to simulate the welding process and post weld heat treatment (PWHT) to find the factors affecting the failure in tube-to-tubesheet weldments. Residual stresses in two different geometries of tube-to-tubesheet weldment were calculated through uncoupled thermal-structural analysis. The results showed that the values of residual stresses are higher in heat exchanger of site 1 than site 2 due to more weld passes and geometry of connection. Also, the maximum stress in site 1 occurs at the shellside... 

Strain and stress concentrations are studied for elastomers at finite deformations. Effects of strain-induced crystallization, filler reinforcement and deformation rate are also investigated, and micromechanical descriptions are provided for the observed results. A simple problem is subjected to finite element simulations to show the results evidently. Material parameters are obtained from experimental tests conducted on standard tensile samples of filled and unfilled natural rubber (NR) as well as styrene–butadiene rubber (SBR) as crystallizing and non-crystallizing rubbers, respectively. In all simulations, the strain concentration factor KE is shown to decrease monotonically where the... 

In the present research, results from the finite element (FE) stress analysis of 108 models, validated using test data obtained from the experimental investigation, was used to propose probability distribution models for stress concentration factors (SCFs) in internally ring-stiffened tubular KT-joints under four types of in-plane bending (IPB) loads. The SCF is one of the crucial parameters in the fatigue reliability analysis of tubular joints. It exhibits considerable scatter which calls for greater emphasis in accurate derivation of its governing probability function. According to the knowledge of the authors, no comprehensive research has been carried out on the probability distribution... 

In this study, based on multipole expansion method an analytical treatment is presented for the anti-plane scattering of SH-waves by an arbitrarily oriented elliptic cavity/crack which is embedded near the interface between exponentially graded and homogeneous half-spaces. The cavity is embedded within the inhomogeneous half-space. The boundary value problem of interest is solved by constructing an appropriate set of multipole functions which satisfy (i) the governing equation in each half-space, (ii) the continuity conditions across the interface between the two half-spaces, and (iii) the far-field radiation and regularity conditions. The analytical expressions for the scattered... 

The scattering of in-plane P- and SV-waves by a multi-coated circular nanofiber with deformable interfaces is of interest. To this end, in the present work, after introducing two kinds of interface momenta defined as the derivative of the interface excess kinetic energy with respect to the average and relative velocities at the interface, we extend the elastostatic theory of Gurtin et al. (1998) on deformable interfaces to the elastodynamic theory and derive the interface equations of motion using Hamilton principle. The effects of the generalized interface properties including the interface inertial parameters and interface stiffness towards stretch and slip on the dynamic stress... 

A finite element-based hierarchical multiscale modeling scheme is presented and used for the analysis of nanotube-reinforced polymer composites. The scheme presented here consists of micro- and macroscale boundary value problems linked together using a computational homogenization scheme. Using the presented hierarchical multiscale scheme, we have studied nanotube-reinforced polymer composites, and the elastic properties are determined. Using different representative volume elements (RVEs) representing different volume fractions of aligned nanotubes, the effect of the nanotube volume fraction and the existence of an interphase layer on the effective elastic modulus of the nanocomposite are...