Sharif Digital Repository

Adhesive and cohesive properties of the plasma-sprayed hydroxyapatite (HA) coatings, deposited on Ti-6Al-4V substrates by varying the plasma power level and spray distance (SD), were evaluated by an indentation method. The crystallinity and the porosity decreased with increasing both of these two parameters. The microhardness value, Young's modulus (E) and coating fracture toughness (K C ) were found to increase with a combinational increase in spray power and SD. The Knoop and Vickers indentation methods were used to estimate E and K C , respectively. The critical point at which no crack appears at the interface was determined by the interface indentation test. This was used to define the... 

We report on fabrication of halide perovskite solar cells using a two-step spin-spray coating rout. The applied method is one of the most straight forward procedures for fabricating uniform stoichiometry and crystalline perovskite cells. To fabricate a high quality perovskite layer, various concentrations of methyl-ammonium iodide (CH3NH3I) were sprayed on a spin coated PbI2 layer using a simple airbrush gun. The characterization results indicate that the size of cuboid perovskite morphology depends on the concentration of methylammonium iodide in the spray procedure. The photovoltaic performance of the fabricated solar cells has been measured and a high dependency on the cuboid sizes was... 

HVOF-sprayed coatings (WC-17%Co) and hard chromium coatings corrosion resistances have been compared through electrochemical polarization test in 3.5% NaCl solution. WC-17%Co alloy coatings were deposited on mild steel substrates by High Velocity Oxy-Fuel (HVOF) spray process. The layers of standard and crack free hard chromium coatings were prepared by using Direct Current (DC) and Pulse Current (PC) electroplating process on the mild steel substrates. Hard chromium coatings was characterized as a reference material, to verify whether HVOF-sprayed coatings are suitable as a hard chromium coatings replacement. The microstructure of the coatings was examined by OM, SEM and XRD. Standard hard... 

In the present work, the hot corrosion behavior of two types of multilayer plasma sprayed TBC were investigated and compared with functionally graded and conventional TBCs. These kinds of multilayer coatings consisted of nano/μ alumina as a top coat on YSZ layer, a metallic bond coat and a functionally graded intermediate layer deposited between YSZ and bond coat layers. All the layers were sprayed on the Ni-base super alloy substrate. The hot corrosion resistance of the plasma sprayed coatings was examined at 1050 °C for 40 h, using a fused mixture of 45 wt% Na2SO4 + 55wt%V2O5. Before and after hot corrosion, the microstructure and phase analysis of the coating were studied using scanning... 

Thermal-sprayed MCrAlY coatings have become widespread in various industries such as power plants, aeronautics, and oil and gas firms. High-temperature oxidation behavior of these coatings is therefore of significance. Spraying of two prevalent MCrAlY powders (NiCoCrAlY and CoNiCrAlY) on Hastelloy substrate by high velocity oxygen and fuel method and exposing them to 1000 °C air for resolving of their cyclic oxidation behavior are presented in this paper. The coatings were characterized by x-ray diffraction, scanning electron microscopy and energy-dispersive x-ray spectroscopy. The obtained oxidation kinetic indicated that at 1000 °C, the thermally sprayed NiCoCrAlY coating has greater... 

In recent years, thin silver nanowires (Ag NWs) with diameters smaller than 150 nm have been synthesized by implementation of NaCl or FeCl3 as reaction promoters and high molecular weight polyvinylpyrrolidone (PVP) as the capping agent. However, the yield of Ag NWs still remains low, mostly due to the insufficient aspect ratio (AR) of the synthesized nanostructures and the production of Ag nanoparticles, which is an undesirable by product. This study proposes a modified technique to alleviate the problem by using a mixture of FeCl3/CuCl2 as the reaction promoter and two different types of PVP with molecular weight of 360 k and 40 k as the capping agents. The appropriate mixtures of... 

The effects of severe shot-peening process and formation of a nanostructured surface layer on mechanical properties of A356.0 alloy were investigated in this paper. X-ray diffraction analyses revealed that the average size of near-surface grains in severe shot-peened specimens is 75.8 nm. Three types of disk-shaped specimens, non-treated, conventionally shot-peened, and severely shot-peened were subjected to pin-on-disk wear test in the dry condition, in different loading and sliding speeds. Shot-peening process increases both hardness and roughness of the surface, and these two factors have, respectively, positive and negative effects on wear resistance. However, because of high-density... 

Plastic packaging is causing a serious environmental concern owing to its difficulty in degrading and micro-particulates' emissions. Developing biodegradable films has gained research attention to overcome ecological and health issues associated with plastic based packaging. One alternative substitute for petroleum-based plastic is nanocellulose based films, having distinguishing characteristics such as biodegradability, renewability, and non-toxicity. Nanocellulose is classified into three major types, i.e., cellulose nanofibril, cellulose nanocrystals, and bacterial nanocellulose. However, the scope of this review is limited to cellulose nanofibril (CNF) because this is the only one of...