Sharif Digital Repository

Variability and uncertainty of wind and photovoltaic (PV) generations greatly influence technical and financial aspects of power systems. This paper examines the potential impacts of large-scale wind and PV farms on reliability level of composite generation and transmission systems. At first, reliability models of renewable-based units are developed. In these models, both component failure rates and uncertainty nature of renewable resources are taken into account. Using the proposed technique, the multi-state analytical models of a wind farm placed in Manjil and a PV farm placed in Jask both in Iran are extracted. Then, reliability studies of high renewable-energies penetrated power system... 

To attain an ongoing electricity economy, developing novel widespread electricity supply systems based on diverse energy resources are critically important. Several photovoltaic (PV) technologies exist, which cause various pathways to produce electricity from solar energy. This paper evaluates the competition between three influential solar technologies based on photovoltaic technique to find the optimal pathways for satisfying the electricity demand: (1) multicrystalline silicon; (2) copper, indium, gallium, and selenium (CIGS); and (3) multijunction. Besides the technical factors, there are other effective parameters such as cost, operability, feasibility, and capacity that should be... 

Variability and uncertainty of wind and photovoltaic (PV) generations greatly influence technical and financial aspects of power systems. This paper examines the potential impacts of large-scale wind and PV farms on reliability level of composite generation and transmission systems. At first, reliability models of renewable-based units are developed. In these models, both component failure rates and uncertainty nature of renewable resources are taken into account. Using the proposed technique, the multi-state analytical models of a wind farm placed in Manjil and a PV farm placed in Jask both in Iran are extracted. Then, reliability studies of high renewable-energies penetrated power system... 

Well-crystallized TiO2 and neodymium (Nd)-doped TiO2 nanoparticles with various doping levels were synthesized by hydrothermal method and utilized as the photoanode of nanostructured solar cells. The results indicated that Nd-doping was caused the absorption spectra shift to higher wavelength while the morphology and surface area were unchanged. As a result, by employing 0.4 mol% Nd in the TiO2 photoelectrode, the overall conversion efficiency of the cell reached 9.08% which is 26% higher than pure one. Based on the photo-electrochemical characterizations, the improvement is a consequence of electrons injection increment from dye to TiO2 conduction... 

This study attempts to investigate a new way for cooling PV cell using natural vapor as coolant. The performance of solar cell was examined on simulated sunlight. The natural vapor encountered backside of PV cell vertically in various distribution and different mass flow rates. Also, the effect of natural vapor temperature in cooling performance was analyzed. Results indicated that the temperature of PV cell drops significantly with increasing natural vapor mass flow rate. In detail, the PV cell temperature decreased about 7 to 16°C when flow rate reaches 1.6 to 5grmin-1. It causes increasing electrical efficiency about 12.12% to 22.9%. The best performance of PV cell can be achieved at high... 

A comparative study has been made of hybrid solar cells based on poly(3-hexylthiophene) (P3HT) and different nano-structures of TiO2. Electrospinning, which is a low cost production method for large area nanofibrous films, was employed to fabricate TiO2 nanofibers and spin coating method was employed to fabricate organic-inorganic hybrid solar cells based on P3HT and TiO2 nanostructures. The performance of the hybrid solar cells was analyzed for four density levels of the TiO2 nanostructure. It was found that higher densities of TiO2 leads to more interface area and generates excitons, so that the power conversion efficiency increases to... 

Today, regarding the limitation and environmental side effects of fossil fuel resources, solar hydrogen production is one of the main interests in the energy research area. The development of visible light sensitized semiconductors based on non-toxic components, low cost and available bio-species is an ongoing approach for H2 generation based on water splitting reactions. Here, two different morphologies of TiO2 photoanodes, nanoparticulated and nanotubular, have been modified with simply extracted bacteriorhodopsin (bR) without any linker. Achieving a significant enhancement in photoconversion efficiency of TiO2 photoanodes, η% was increased from 2.9 to 16.5 by bR addition to the TiO2... 

We report on fabrication of halide perovskite solar cells using a two-step spin-spray coating rout. The applied method is one of the most straight forward procedures for fabricating uniform stoichiometry and crystalline perovskite cells. To fabricate a high quality perovskite layer, various concentrations of methyl-ammonium iodide (CH3NH3I) were sprayed on a spin coated PbI2 layer using a simple airbrush gun. The characterization results indicate that the size of cuboid perovskite morphology depends on the concentration of methylammonium iodide in the spray procedure. The photovoltaic performance of the fabricated solar cells has been measured and a high dependency on the cuboid sizes was... 

In dye-sensitized solar cells recombination reactions at the TiO2 photoanode with the electrolyte interface plays a critical role in cell efficiency. Recombination of injected electrons in the TiO2 with acceptors in the electrolyte usually occurs on uncovered areas of TiO2 surfaces. In this work, we report electropolymerization of polymer films on nanoporous TiO2 electrode surfaces using an ionic liquid as the growth medium. The choice of ionic liquid as the growth medium for this study is based on the insolubility of dye N719 in this electrolyte, thus avoiding dye molecule detachment from the TiO2 photoanode surface over the entire potential range investigated during the... 

Providing solar hydrogen as a clean energy resource is one of the human challenges for future. Controlling oxygen vacancies as well as surface morphology in metal oxide semiconductors enables developing PEC H2production in some understood ways. Here, the influence of simple change in annealing atmosphere, air and pure oxygen, on photoresponse of nanocrystalline WO3has been studied completely. Results revealed that such slight change in annealing procedure increases effective surface interface and donor density by 77 and 72%, respectively. These effects and also retarding recombination of photogenerated electro-hole pair resulted in photocurrent enhancement under solar like illumination more... 

Graphitic carbon nitride (g-C3N4) is a metal-free conjugated polymer constructed from two-dimensional sheets with a bandgap energy of 2.7 eV, which makes it an applicable and efficient visible-active photocatalyst for H2 production. In the present study, the basic concepts and principles of photocatalytic water splitting have been discussed, and a guide for the selection of appropriate photocatalysts, focusing on the g-C3N4 nanomaterials, has been proposed. Our approach is mainly concentrated on evaluating two factors, namely the solar-to-hydrogen (STH) conversion and apparent quantum yield (AQY) for different photocatalysts, to provide an in-depth analysis and a framework for solar H2... 

Organic-inorganic perovskite solar cells (PSCs) have gained considerable attention owing to their impressive photovoltaic properties and simple device manufacturing. In general, PSC employs a perovskite absorber material sandwiched between an electron and hole selective transport layer optimized with respect to optimal band alignment, efficient charge collection, and low interfacial recombination. The interfaces between the perovskite absorber and respective selective contacts play a crucial role in determining photovoltaic performance and stability of PSCs. However, a fundamental understanding is lacking, and there is poor understanding in controlling the physical processes at the... 

In the current investigation, four novel donoracceptor type organic dyes including (DPA-Ba, DPA-Hy, DPA-Rh, DPA-Cy), are proposed and their photophysical and electrochemical properties as well as dye-sensitized solar cell performance are systematically investigated. Among these dyes diphenylamine is utilized as an-electron donor while barbituric acid, hydantoin, rhodanine-n-acetic acid and cyano acetic acid, are proposed as anchoring groups as dye-sensitized solar cells (DSSCs). The synthesized dyes are characterized using FT-IR, NMR, mass spectrometry, absorbance and electrochemical measurements. The photophysical, electrochemical and photovoltaic properties of the solar cells based on... 

In this study, quick route-coating is practiced to substitute methyl ammonium (MA) cation with formamidinium (FA) at different ratios. Through optimizing the MA:FA ratio, a maximum power conversion efficiency (PCE) of 8.31% is achieved for holes transporting material-free MA0.8FA0.2PbI3 mixed PSCs with the JSC of 19.02 mA/cm2, VOC of 0.859 V and FF of 50.88%. Then, to improve the performance, stability and carrier transport dynamic, various additives (PVA, PVP, PEG and EC) are incorporated into the perovskite layer. The treatment of perovskites with additives has proved to cause significant changes in the surface roughness, charge accumulation, charge transport, charge transport resistance,... 

This article contributes to the ongoing debate about whether, how, and under what conditions latecomer countries can become producers of new technology and innovation, thereby catching up with technological leaders. Recent work on sectoral systems of innovation and in the evolutionary economics literature suggests that successful latecomers can move into new technological or industrial domains. They specialise in domains that present more frequent windows of opportunity, shorter technological cycles, flatter learning curves and easier access to relevant knowledge than others. This study investigates the role and significance of two hitherto neglected dimensions of technological regimes that... 

This paper proposes a robust investment and operation model to attend the power and heat needs of a microgrid (MG) connected to the distribution system. The optimization algorithm decides on the best investment and operation of combined heat and power (CHP), boilers, PV power generation and battery energy storage systems (BESS). For the BESS, the algorithm estimates the optimal energy storage capacity (MWh) as well as the maximum hourly delivery capacity (MW). The non-linear and non-concave heat rate chart is recast by a mix-integer linear model to have a tractable and precise model. The model considers the uncertain in some parameters using probability density function (pdf) to portrait its... 

Waves encountering can cause significant ship motions and affect the photovoltaic power generation capacity in All-Electric Ships (AES) during extreme conditions. In this paper, a comprehensive strategy is proposed to examine the impact of modern vessels' movements on the PV system output and the ship power quality during various operating scenarios. The proposed theoretical model-based technique determines ship angles in a wave collision and assesses sun-related angles concerning the vessel motions. Based on the panel angles, the solar irradiance and the PV system power variations can be derived. The developed method can simultaneously evaluate the effect of ship motions on the photovoltaic... 

This paper describes the designing and evaluation of an alternative energy system which consists of PEMFC, PV, PEM electrolyser, methane reformer and hydrogen tank. In order to find out the minimum capacity of the components, a system sizing model is developed in MATLAB based on meteorological and electrical demand data. Three scenarios are considered based on different combinations of solar energy and fossil fuel energy as energy resources. The heating energy produced by the fuel cell is recovered for supplying domestic hot water while the system would supply electrical energy. Results show that system sizing strongly depends on scenarios and unit cost of electricity decreases through the... 

Distributed generation (DG) units are often interfaced to the main grid using power electronic converters including voltage-source converters (VSCs). A VSC offers dc/ac power conversion, high controllability, and fast dynamic response. Because of nonlinearities, uncertainties, and system parameters’ changes involved in the nature of a grid-connected renewable DG system, conventional linear control methods cannot completely and efficiently address all control objectives. In this paper, a nonlinear adaptive control scheme based on adaptive backstepping strategy is presented to control the operation of a grid-connected renewable DG unit. As compared to the popular vector control technique, the... 

Different structures of TiO2 photoelectrodes are fabricated with various arrangement modes of the layers. TiO2 nanoparticles, synthesized by stabilizing agent free non-hydrolytic sol–gel method, are employed as the under layer, whereas carbon-doped TiO2 hollow spheres, prepared by hydrothermally grown carbon template, are used as the scattering layer of solar cells. The nanoparticles (22 nm) have anatase structure, while 300–700 nm hollow spheres show mixtures of anatase and rutile phases. X-ray photoelectron spectroscopy confirms that carbon is doped into TiO2 hollow spheres, resulting in a decrease in band gap energy in the range 2.96–3.13 eV compared with 3.04 eV band gap energy for the...