Sharif Digital Repository

In this paper, a new structure for the rotor of the Brushless Doubly-Fed Machine (BDFM) is introduced to reduce the machine's torque ripple. The ripple has a considerable effect on the machine start up. At the first section of the paper, analytical expressions for the air gap permeance distribution, the air gap MMF distribution, cogging torque and back EMF are presented. Then, the effects of skewing the rotor loops are analyzed. Finally, the relation between non-skewed quantities and their values in skewed coordinate are introduced  

A space vector modulation (SVM) approach is proposed to control a four-switch rectifier with power factor correction and compensating the effect of capacitors voltage ripple. The theory and performance of this method are presented, and the method effectiveness is demonstrated by extensive simulations. The simulation results show that the capacitor voltage ripple effects in the output voltage and current shaping can be omitted and the rectifier can work agreeably under high power factor condition although capacitors voltage is not balance. The allowable amount of this unbalanced value of filter capacitors is determined  

Cascaded split-source inverter (CSSI) is a new single-stage modular multilevel topology. Each cell of this converter converts DC to AC power in the buck or boost operation mode without any additional power switch. This paper develops a design method based on a detailed model for CSSI. This model shows that energy storage elements experience double-fundamental frequency ripples besides high-frequency ones. It accurately calculates voltage gains and capacitor voltage and inductor current ripples. On the other hand, common carrier-based multilevel modulations have been modified in terms of both reference and carrier signals to control the inverter under symmetric and asymmetric conditions. With... 

Cascaded split-source inverter (CSSI) is a new single-stage modular multilevel topology. Each cell of this converter converts dc to ac power in the buck or boost operation mode without any additional power switch. This article develops a design method based on a detailed model for CSSI. This model shows that energy storage elements experience double-fundamental frequency ripples besides high-frequency ones. It accurately calculates voltage gains and capacitor voltage and inductor current ripples. On the other hand, common carrier-based multilevel modulations have been modified in terms of both reference and carrier signals to control the inverter under symmetric and asymmetric conditions.... 

Using tight binding theory the effect of topological ripples on the electronic band structure, density of states (DOS), and Fermi velocity of graphene are studied. The results show that by an increase in the ripple height the graphene Fermi velocity decreases and its DOS increases.- Moreover, we show that an increase in the ripple period causes the graphene band gap and DOS to decrease and its Fermi velocity to increase  

We develop an analytic approach to investigate the effect of reflection amplitude and group delay ripples of the dispersive device on the performance of phase-modulated microwave-photonic filters. Experimental results conform to our proposed analytical approach  

Switched reluctance motors (SRM) are one of the most reliable and cost effective motors and their applications are increasing in industry. However, it suffers from high level of torque ripple. In this paper, a new configuration for stator and rotor of SRM is presented. In the proposed method, a new saliency is developed to remove negative torque and therefore decrease torque ripple and acoustic noise, increase efficiency and as a result, expand speed range. The simulation results demonstrate that the new motor structure has a smooth torque profile with possibility to work at higher speed lower acoustic noise  

Here, the authors propose a new approach for realising wideband and polarisation-independent antireflection coating, based on a metamaterial composed of a subwavelength array of metallic pillars with a square cross-section. The effective impedance of the array can be duly adjusted by the size and distance of the pillars. As such, the authors design the effective impedance of the antireflection coating to be the geometrical mean of the impedance of upper and lower media and choose its height to be quarter of operating wavelength. Doing so, the reflection vanishes at the desired frequency and fractional bandwidth of 56% is achieved with a criterion of 10% reflectance (the refractive index of... 

In this paper, the axiomatic design is introduced for controlling a power electronic converter. The main idea of axiomatic design is to introduce variables affecting the desired performances of the system most independently possible. The control process is presented for a Buck converter to achieve constant efficiency and output voltage ripple. ©2008 IEEE  

In this paper, a new interleaved DC–DC converter based on a coupled and a single input inductor is proposed. The suggested high step-up converter utilizes various inductive and capacitive methods to transfer magnetic energy more efficiently. The output voltage is regulated with the switches' duty cycle and the coupled inductor (CI) turns ratio, which provide a wide output voltage range. Interleaving improves the converter reliability, employs both the first and third areas of CI's B-H plane, cancels DC component of the CI, and reduces the input current ripple of the proposed converter with twice switching frequency. Utilization of two output ports for voltage stress and ripple reduction in...