Sharif Digital Repository

In this work, a basic model for numerically simulating matrix acidizing in carbonate formations is developed. This model employs laboratory linear acid core-flooding data and avoids any fitting parameters. Wellbore-scale numerical simulation is based on finite-volume method with Cartesian coordination and cubic meshing. Mass transfer equations are based on fluid front tracking and the momentum transfer equation is the Navier-Stokes equation for flow in porous media. The effect of fine-scale dissolution phenomena of carbonate rocks are translated into the coarse-scale by homogenization. In this work, it is tried to achieve a simple but logical approach towards a correct simulation, avoiding... 

Acidizing is one of the most effective techniques to remove the formation damage and restore (or even increase) the permeability of the near wellbore region. Although this technique is widely used to resolve the skin problem, it could initiate new damages itself that hinder the fluid flow and decrease the well production, consequently. Acid-oil emulsion and sludge formation are known as two major induced formation damage and the main reasons for the oil well acid treatment failures.When the HCl is reacted with asphaltenic crude oil during matrix acidizing, it results in unexpected damage at the near wellbore region and hinder the fluid flow through certain mechanisms include:
1- Pore... 

Acidizing is one of the widely used practices of formation damage remediation. The success of this rather expensive job depends on the precise design and operation. Though, improper execution of an acid job, not only does not improve the formation damage but also can contribute to even more damage itself. For this purpose, it is critically important to thoroughly design an acidizing job conducting extensive lab experiments and utilizing numerical tools before operation in order for a successful acidizing. Unlike, carbonate acidizing, the chemistry of sandstone acidizing is very complex and challenging because of the wide variety of minerals and aqueous species present in the system. Hence, a... 

Well stimulation techniques are used to increase the productivity of oil and gas wells. One of the effective well stimulation methods, is matrix acidizing. During matrix acidizing, acidic solution is injected into the formation at pressure below the formation fracture pressure. Most of the time, acid needs to be reached to low permeability layers for more efficient damage removal. Divertors are used for diverting acid from high permeability to low permeability layers.Successful performance of a viscoelastic acid during an acid job, is highly dependent on the surfactant rheological properties. For a betaine viscoelastic surfactant, we have studied the effect of different parameters on the... 

Acidizing operation is performed in oil and gas reservoirs with the aim of overcoming formation damages, increasing permeability and reducing skin factor. In carbonate reservoir, the hydrochloric acid increases the permeability of the areas around the well to a more than its initial value by dissolving part of the formation minerals. Considering that most of Iran's oil and gas reservoirs are in the category of carbonate reservoirs, it is important to study the reaction kinetics of carbonate minerals and acids used in acidizing operation. The complex and multifactorial nature of the acidizing operation in the reservoirs has made it very difficult to design a successful and optimal operation.... 

One of the best stimulation methods for oil and gas wells is matrix acidizing in order to increase the near wellbore permeability. in acidizing, good acid coverage in different layers is one the main goals. so, various methods have been presented. important part in using these methods is to not damage formation and economic matters. modern methods utilize VES acids for this purpose. viscoelastic characteristics of these materials by formation of miscellaneous, increases the apparent viscosity by a large degree. for this reason, VES fluids can be used to improve acid divergence in acid injection operation. acid system based on viscoelastic surfactants that is changed to gel instantly, can be... 

With the production from the reservoirs, the amount of in-situ oil storage has decreased and there is a need to increase oil recovery (EOR) from the reservoir. Increased oil recovery (EOR) includes operations such as acidizing and hydraulic fracturing. Considering the economic and high operational costs and geomechanical complexities, as well as the technical progress of hydraulic fracturing and its future; It is necessary to manage hydraulic fracturing operations optimally. This research is about hydraulic fracturing and its main goal is to optimize the parameters of the fracture or the geometry of the fracture. The research study was carried out on the Bangistan Reservoir located in the... 

The Oil wells are usually damaged because of the drilling process and production scenarios or fluid injection during EOR processes. These damages would critically affect the rate of production and injectivity of the well in the form of plugging damage. Different methods are used to fix these damages and increase the production flow from the oil wells. One of the most widely used well-stimulation methods to remediate this challenge is well acidizing. Although this method has very high efficiency in improving the ability of wells, if it is not designed and implemented correctly and optimally, it can cause induced damage and even lead to the well shutting. This challenge is especially reported... 

The process of injecting acid or acidizing, is one of the most common ways to stimulate oil and gas wells. The purpose of this process is to increase the productivity of the well by increasing the permeability of the reservoir rock around the well. This is especially important in carbonate reservoirs due to damage to the formation and low intrinsic permeability in some places. In order to minimize the effects of structural damage, conventional wormhole channels are created to pass through the injured area. One of the important factors in acid validation is achieving optimal injection rate, which means obtaining the highest permeability with the lowest amount of injected acid.Numerous... 

Formation acidizing is one of the best well stimulation methods to remove reservoir damage and improve recovery of oil and gas well. The proper design of acidizing operations can significantly improve the production of a formation. In the meantime, causing formation damage and precipitation in oil flowlines, which may be caused by the incompatibility of the stimulation fluid with the reservoir fluid and rocks, is one of the most serious problems in the operation, which reduces permeability and oil/gas production. As a result, the success of the acidizing operation requires to study the interaction of components of operation (acid, reservoir water, formation rock, and acid additive)... 

Reactive flow through porous media is a phenomenon of high importance in various study subjects i.e. groundwater, mining, geology, and petroleum reservoirs. In petroleum engineering, a related topic to this phenomenon is the dissolution of the rock matrix due to acidizing. Near_wellbore carbonate rock acidizing has been used for decades in the petroleum industry to enhance the productivity of the well. Optimal injection rate is a key question in such operations. Various models have been used to simulate reactive flow in porous media many of which are continuum-scale that face significant uncertainty regarding the pore-scale nature of the flow, mass transfer, reaction, and subsequent changes... 

Acidizing is the most widely performed job to remove the formation damage, and enhance the oil recovery. Different models have been introduced to design the optimized condition for acidizing. However, none of them are able to predict the optimum injection flow rate in the actual application. As a result, Calcite cores are extracted from reservoirs for conducting experiments and modifying the present models. Nevertheless, acidizing is an intrusive technique destroying the costly extracted cores. Thus, there is a need to construct calcite cores of various porosities and permeabilities to take advantage of them in acidizing modelling.Microbially induced calcite precipitation is a well-known... 

Carbonate reservoir acidizing is one of the most important well stimulation operations that has been widely used in recent years. Modeling the operation prior to any laboratory tests has always been one of the motivations of scientists in recent years due to the complexity of modeling to consider both mass transfer and reaction phenomena. There are several models have been proposed to simulate the acid injection process in carbonate rocks in recent years, the most important one is the Two-Scale Continuum Model (TSCM). This model utilizes the combination of Darcy-scale transfer and reaction equations and a series of pore scale relations to investigate acid injection into two-dimensional...