Sharif Digital Repository

Self-organised and vertically oriented titanium oxide nanotube array (TNTA) has been synthesised by potentiostat anodisation of Ti foil in fluoride-based electrolyte. By varying the anodisation voltage from 8 V to 24 V it was possible to gradually change the topologies of nanotubes. The size of TNTAs was measured using SEM images and also determined based on a non-destructive optical method. In addition, photoelectrochemical properties of nanotubular TiO2/Ti electrodes were examined by anodic photocurrent response, potentiodynamic polarisation measurements and electrochemical impedance spectroscopy. A general equivalent circuit model was proposed for photoelectrochemical system consists of... 

Pure Zn and Zn matrix composite coatings containing nano-sized SiC particles with an average size of 50 nm were prepared from the zinc sulfate bath. The effects of the pulse frequency, maximum current density and duty cycle on the amount of particles embedded were examined. Electron microscopic studies revealed that the coating morphology was modified by the presence of SiC nanoparticles. In the presence of SiC nanoparticles deposit grows in outgrowth mode resulting in a very rough and porous microstructure. However, at very low and very high duty cycles a smooth and pore free microstructure was obtained. Corrosion resistance properties of the coatings were studied using potentiodynamic... 

The effect of some inhibitors consisting of sodium nitrite (NaNO 2), sodium nitrate (NaNO 3), sodium molybdate (Na 2MoO 4), and sodium silicate (Na 2SiO 3) on the corrosion behavior of aluminum alloy 3303 (UNS A93303) in a water and ethylene glycol (C 2H 6O 2) mixture was investigated. In the first part, the tests were established without any galvanic coupling. In the second part, the tests were established with galvanic connections between the aluminum alloy and mild steel, stainless steel, copper, brass, and solder. Results show that the best corrosion inhibitor in both situations is sodium nitrate, according to its abilities to reduce corrosion rate, passivate the aluminum surface, and... 

Due to unique properties of NiTi shape memory alloys such as high corrosion resistance, biocompatibility, super elasticity and shape memory behavior, NiTi shape memory alloys are suitable materials for medical applications. Although TiO2 passive layer in these alloys can prevent releasing of nickel to the environment, high nickel content and stability of passive layer in these alloys are very debatable subjects. In this study a NiTi shape memory alloy with nominal composition of 50.7 atom% Ni was investigated by corrosion tests. Electrochemical tests were performed in two physiological environments of Ringer solution and NaCl 0.9% solution. Results indicate that the breakdown potential of... 

Hydroxyapatite (HA) coatings in and onto anodized TiO2 nanotube arrays were presented and prepared by electrophoretic deposition technique (EPD). Coatings were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). EPD proved to be an innovative and versatile technique to coat HA on and into nanotubular structures of TiO2 with enhanced adhesion between nanotubes and HA particles provided by mechanical interlocking. After EPD of HA on TiO2 layer, samples were sintered at 400 °C, 600 °C and 800 °C for 2 h in an Ar atmosphere. Effect of EPD processing parameters on thickness of the deposits and rate of deposition was elucidated for HA coatings on the nanotubular TiO2... 

The formation of the oxide layer with Zr compounds on AZ31 Mg alloy processed by two-step plasma electrolytic oxidation (PEO) has been investigated. After the PEO process first in an alkaline phosphate electrolyte and second in an acid electrolyte containing K2ZrF6, the microstructure, chemical composition, and phase composition of the oxide layers were analyzed via SEM, EDS, and XRD, respectively. The electrochemical reaction and the high temperature caused by the plasma discharges in the electrolyte were the main factors leading to the fabrication of an oxide layer containing Zr compounds on AZ31 Mg alloy. The micro-pores were filled with ZrO2 formed during the PEO process. The results of... 

Alumina-silicate composite coatings were formed on titanium substrate by plasma electrolytic oxidation (PEO) process using a silicate-based electrolyte containing alumina nanoparticles. Microstructure, chemical and phase compositions, and thickness of the coatings were investigated to determine, coating mechanism and probable reactions during the process. The effect of processing time on corrosion resistance of the coatings was investigated using the potentiodynamic polarization test. Barrier layer (TiO2) formation, micro arcs occurrence, and electrolyte ionization were the main stages of PEO coating growth process. Alumina nanoparticles were incorporated into the coating by cataphoretic and... 

Electrophosphating is the novel method for accelerating the low temperature phosphating bath. This method can be performed as cathodic and anodic treatments. Both of them influence the coating deposition mechanism and therefore coating properties. In this study Zn-Ni electrophosphate coating was applied on galvanized steel using cathodic and anodic electrochemical methods. Microstructure, composition and corrosion resistance of coating were characterized by using a scanning electron microscopy, X-ray diffraction method and potentiodynamic polarization test respectively. The results of this study indicated that, by using cathodic method, compact phosphate coating with high corrosion... 

Nanostructured molybdenum oxide having a particle size in the range of 30-80 nm was prepared by potentiodynamic electrodeposition method, and the effects of H2SO4 concentration on its capacitive behavior were studied by cyclic voltammetry, galvanostatic discharge, and electrochemical impedance spectroscopy. Poor to fair capacitive behaviors were witnessed depending on the electrolyte concentration and conditions of charge/discharge. Increasing acid concentration to 0.02 M had favorable effect, while beyond that, the effect was detrimental. Capacitance around 600 F g-1 was recorded in the potential range of 0 to -0.55 V vs. Ag/AgCl  

Electrophosphating is the novel method for accelerating the low temperature phosphating bath. This method can be performed as cathodic and anodic treatments. Both of them influence the coating deposition mechanism and therefore coating properties. In this study Zn–Ni electrophosphate coating was applied on galvanized steel using cathodic and anodic electrochemical methods. Microstructure, composition and corrosion resistance of coating were characterized by using a scanning electron microscopy, X-ray diffraction method and potentiodynamic polarization test respectively. The results of this study indicated that, by using cathodic method, compact phosphate coating with high corrosion... 

Accumulative roll bonded (ARBed) AA1050 and Al-2 vol% SiCp (AMC) samples were anodized in an H2SO4 electrolyte to improve corrosion resistance. The SEM images revealed that the anodic oxide's morphology is significantly dependent on the microstructure of the ARBed bare samples, owing to high internal energy that accelerates Al consumption during anodizing process. Potentiodynamic polarization measurements and EIS evaluation showed that anodic oxide improves the corrosion resistance of both ARBed AA and AMC samples; however, the electrochemical behavior of the processed samples changed due to the formation of a complex oxide structure comprising of twisted pore channels and attack routes. ©... 

In order to improve titanium corrosion behavior, we can increase the thickness of oxide layer on titanium surface during anodizing process and by electrochemistry. In this research, self-color anodizing of Ti in sulfuric acid was done, and anodizing layers were created in different colors. The highest value of chromaticity was 37.8 for the anodized sample in 10 V, and the lowest value was 8.6 at 15 V. The oxide layer thickness was calculated by optical method (light refraction). The anodic film thickness increased by increasing the anodizing voltage. The highest thickness of anodic film was 190 nm in sulfuric acid solution for the anodized sample in 80 V. Corrosion resistance of anodized Ti... 

This study focuses on the effect of co-deposition of PTFE and/or MoS 2 particles on the morphology, wear, and corrosion properties of electroless nickel coating. The composite coating of EN-PTFE-MoS 2 was heat treated at different temperatures for hardness investigations. The surface morphology of coatings was characterized by scanning electron microscopy. Pin-on-disk and potentiodynamic polarization tests were used to study the tribological and corrosion properties of the coatings, respectively. Results of hardness analysis revealed that the hardness of electroless nickel coatings was increased by the heat treatment, and its maximum was gained at 400°C. Wear investigations showed that... 

Inclusion of carbon nanotubes (CNTs) into the titanium dioxide coating on 1050 aluminium alloy was studied with the aim at enhancing the corrosion resistance of the surface. Composite coatings with various contents of CNTs were prepared via the sol-gel method and dip coating. XRD and FTIR phase and structural evaluations showed the presence of anatase phase in all thin films. Concomitant enhanced corrosion behaviour in the presence of CNTs was resulted from polarization potentiodynamic test. Band-gap evaluation was performed using absorbance spectra of coatings and showed considerable decrease of band-gap energy in the presence of CNTs. Photocatalytic properties and hydrophilicity of... 

The adhesion of hydroxyapatite (HA) as a coating for the AZ91 magnesium alloy substrate can be improved by using the sputtering method and an intermediate layer, such as ZrN. In this study, HA coatings were applied on ZrN intermediate layers at a temperature of 300 °C for 180, 240, 300, 360, and 420 min by ion beam sputtering. A profilometer device was used to study the HA coating thickness, which changed from 2 μm for the 180-min deposition to 4.7 μm for 420-min deposition. The grazing incidence X-ray diffraction analysis method and the Williamson–Hall analysis were used for structural investigation. As the deposition time increased, the crystalline size increased from 50 nm to 690 nm.... 

A composite coating containing silver, fluoride and hydroxyapatite (Ag-FHA) was developed on titanium substrate by sol-gel method. Triethylphosphite, hydrated calcium nitrate, ammonium fluoride and silver nitrate were used respectively, as P, Ca, F and Ag precursors with a Ca:P ratio 1.67 and concentration of silver was 0.3 wt%. Coatings were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and atomic absorption spectrometry (AAS). Potentiodynamic polarization measurements in simulated body fluid proved corrosion protection caused by both Ag-FHA coatings. Antibacterial activity of coatings against... 

In this study, biocompatible ceramic layers containing TiO2 and hydroxyapatite (HA) nanoparticles (TiO2/HA) were deposited on pure commercial titanium (Grade 2) by using plasma electrolytic oxidation and AC power supply. The coating process was carried out in five different solutions for various times at a current density of 500 mA cm−2. To achieve the optimum conditions for thickness and microstructure, the coating process was conducted in solutions with a 3 g L−1 concentration of HA nanoparticles. FESEM, XRD, and FTIR results showed that HA nanoparticles were successfully incorporated into the pores of the layer. Furthermore, the corrosion behavior of the coating layers in the simulated... 

Ti and TiN thin films were deposited by means of electron beam evaporation on stainless steel substrates, and subsequently annealed at different temperatures (650, 750 and 850 °C) in a nitrogen atmosphere. The surface morphology of the films studied by atomic force microscopy (AFM), was found to exhibit specific multifractal properties depending on the annealing temperature. It turned out that the width of the multifractal singularity spectra, f(α), decreased as the annealing temperature increased up to 750 °C, but it increased when the temperature was kept at 750 and 850 °C accompanied by the rapid development of the surface objects. The generalized fractal dimension followed a similar... 

This research focused on the corrosion resistance and microstructure of hybrid additively manufactured (HAM) samples of AISI 420/CX (420/CX SS) stainless steels. Potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and Mott–Schottky analyses as well as the electrochemical noise (EN) technique were used to evaluate the electrochemical behavior of the as-built and heat-treated HAM parts in NaCl solution. The results showed a more protective passive layer formed on the CX SS side. The distribution of Cr-rich M23C6 carbides in matrix of 420 SS side resulted in a lower corrosion resistance compared to the CX SS side. The noise data analysis confirmed an increase in the... 

In this research, submicron bioactive glass (BG) particles were synthesized by a sol-gel process and were then coated on a 316L stainless steel substrate using an electrophoretic deposition (EPD) technique. Stable suspension of bioactive glass powders in ethanol solvent was prepared by addition of triethanol amine (TEA), which increased zeta potential from 16.5 ± 1.6 to 20.3 ± 1.4 (mv). Thickness, structure and electrochemical behavior of the coating were characterized. SEM studies showed that increasing EPD voltage leads to a coating with more agglomerated particles, augmented porosity and micro cracks. The results of Fourier transformed infrared (FTIR) spectroscopy revealed the adsorption...