Sharif Digital Repository

V2O5-TiO2 nanostructured porous layers were grown through micro arc oxidation of titanium in vanadate containing electrolytes. This study sheds light on the effect of the electric current type on the photocatalytic performance of the layers. Surface morphology of the layers was investigated by SEM. The results revealed a porous structure with a pores size of 30-180 nm depending on the frequency and the duty cycle. A uniform porous structure was obtained under the pulse-DC regime. Topographical investigations revealed a rough surface which is favorable for catalytic applications. Our XRD and XPS results showed that the layers consisted of anatase, rutile, and vanadium oxide phases whose... 

Pure titania porous layers consisted of anatase and rutile phases, chemically and structurally suitable for catalytic applications, were grown via micro-arc oxidation (MAO). The effect of applied voltage, process time, and electrolyte concentration on surface structure, chemical composition, and especially photocatalytic activity of the layers was investigated. SEM and AFM studies revealed that pore size and surface roughness of the layers increased with the applied voltage, and the electrolyte concentration. Moreover, the photocatalytic performance of the layers synthesized at medium applied voltages was significantly higher than that of the layers produced at other voltages. About 90% of... 

V2O5-TiO2 porous layers were synthesized via micro-arc oxidation for the first time. The effect of the applied voltage on morphology, composition, and photo-activity of the layers was investigated. The layers, which consisted of anatase, rutile, and vanadium pentoxide phases, revealed an enhanced photo-activity. About 93% of methylene blue solution was degraded on the synthesized layers after 120 min UV-irradiation with a reaction rate constant of k = 0.0228 min-1. The band gap energies of the vanadia-titania and pure titania layers were calculated as 2.56 and 3.39 eV, respectively  

Corrosion of mild steel in aqueous solutions containing hydrogen sulphide was modelled under the condition that an iron sulphide film was formed on the steel surface. In the present model, the iron sulphide forms on the steel surface as a result of a solid state reaction between iron and hydrogen sulphide which has several steps. First a very thin film of iron sulphide nucleates on the steel surface. Then, due to further growth of the initial thin layer, a more porous layer of iron sulphide forms on the initial film. In the present model, it is assumed that mass transfer through the thin iron sulphide layer (i.e. adjacent to the steel substrate) controls the corrosion rate of steel in H 2S... 

In this study, the heat transfer and fluid flow characteristics of a three-dimensional microchannel that is partially filled with a layer of porous medium at its bottom solid wall is investigated. The microchannel is consisted of a clear fluid flow region, solid walls and a porous layer that is attached to its solid bottom wall. A constant heat flux is applied to the bottom wall of the microchannel. Darcy-Brinkman-Forchheimer model is used to simulate the fluid flow inside the porous medium. The novelty of this work is to investigate thoroughly and precisely the effect of using of porous layer configuration in MCHSs on hydraulic and thermal performances. The effect of porous layer thickness,... 

Micro-arc oxidation process was used to synthesize V2O5-TiO2 porous layers for the first time. Surface morphology and topography of the layers were investigated by scanning electron microscope (SEM) and atomic force microscope (AFM). X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques were also employed to evaluate phase structure and chemical composition of the layers. It was found that the V2O5-TiO2 layers consisted of anatase, rutile, and vanadium pentoxide phases fraction of which varied with the applied voltage and the electrolyte concentration. It was also revealed that pore size and surface roughness increased with the applied voltage and the electrolyte... 

A sensitive and selective electrochemical sensor was fabricated via the drop-casting of carbon nanoparticles (CNPs) suspension onto a glassy carbon electrode (GCE). The application of this sensor was investigated in simultaneous determination of acetaminophen (ACE) and tramadol (TRA) drugs in pharmaceutical dosage form and ACE determination in human plasma. In order to study the electrochemical behaviors of the drugs, cyclic and differential pulse voltammetric studies of ACE and TRA were carried out at the surfaces of the modified GCE (MGCE) and the bare GCE. The dependence of peak currents and potentials on pH, concentration and the potential scan rate were investigated for these compounds... 

We have investigated hydrogen sensing properties of electrodeposited Pd clusters on macroporous silicon substrates. Porous layer was prepared by electrochemical etching of p-type silicon (100) wafer in organic electrolyte DMF (dimethylformamide) diluted by HF (%95 Vol. %). The deposition of Pd was carried out by linear voltammetry (LV) technique. This technique was taken for reduction of palladium ions in the potential range from 0.4 V to -1 V vs. SCE, at the scan rate of 20 mV s-1. Some samples were annealed at 300°C for an hour in air to study the effect of heat treatment on their gas sensitivity. Surface structural and chemical properties of the samples were characterised using Scanning...