Sharif Digital Repository

A comparative study has been made of hybrid solar cells based on poly(3-hexylthiophene) (P3HT) and different nano-structures of TiO2. Electrospinning, which is a low cost production method for large area nanofibrous films, was employed to fabricate TiO2 nanofibers and spin coating method was employed to fabricate organic-inorganic hybrid solar cells based on P3HT and TiO2 nanostructures. The performance of the hybrid solar cells was analyzed for four density levels of the TiO2 nanostructure. It was found that higher densities of TiO2 leads to more interface area and generates excitons, so that the power conversion efficiency increases to... 

We report on fabrication of halide perovskite solar cells using a two-step spin-spray coating rout. The applied method is one of the most straight forward procedures for fabricating uniform stoichiometry and crystalline perovskite cells. To fabricate a high quality perovskite layer, various concentrations of methyl-ammonium iodide (CH3NH3I) were sprayed on a spin coated PbI2 layer using a simple airbrush gun. The characterization results indicate that the size of cuboid perovskite morphology depends on the concentration of methylammonium iodide in the spray procedure. The photovoltaic performance of the fabricated solar cells has been measured and a high dependency on the cuboid sizes was... 

We report a simple synthetic approach to grow uniform CH3NH3PbI3 perovskite (PSK) layers free of pinholes via varied portions of silver iodide (AgI) added to the precursor solution. XRD/EDS elemental mapping experiments demonstrated nearly uniform Ag distribution inside the perovskite film. When the 1% AgI-assisted perovskite films were fabricated into a p-i-n planar device, the photovoltaic performance was enhanced by ∼30% (PCE increased from 9.5% to 12.0%) relative to the standard cell without added AgI. Measurement of electronic properties using a hall setup indicated that perovskite films show p-type character after Ag doping, whereas the film is n-type without Ag. Transients of... 

In the current investigation, four novel donoracceptor type organic dyes including (DPA-Ba, DPA-Hy, DPA-Rh, DPA-Cy), are proposed and their photophysical and electrochemical properties as well as dye-sensitized solar cell performance are systematically investigated. Among these dyes diphenylamine is utilized as an-electron donor while barbituric acid, hydantoin, rhodanine-n-acetic acid and cyano acetic acid, are proposed as anchoring groups as dye-sensitized solar cells (DSSCs). The synthesized dyes are characterized using FT-IR, NMR, mass spectrometry, absorbance and electrochemical measurements. The photophysical, electrochemical and photovoltaic properties of the solar cells based on... 

Metal-free D–D–π–A type dyes (i.e., Car-Cy, Car-Rh, Dpa-Cy, and Dpa-Rh) were designed and synthesized for dye-sensitized solar cells (DSSCs). In the structure of the sensitized dyes, an imidazole ring is connected to a carbazole or diphenylamine moiety as a donor while cyanoacetic acid or rhodanine-3-acetic acid was introduced as an acceptor/anchor. The molecular structures of D–D–π–A type dyes were characterized using IR, NMR and MS spectral data. The optical, electrochemical, theoretical, light harvesting property, HOMO/LUMO levels, redox behavior, and photovoltaic properties of the synthesized dyes were evaluated. Among the fabricated photovoltaic devices based on the prepared dye, Dpa-Cy... 

Waves encountering can cause significant ship motions and affect the photovoltaic power generation capacity in All-Electric Ships (AES) during extreme conditions. In this paper, a comprehensive strategy is proposed to examine the impact of modern vessels' movements on the PV system output and the ship power quality during various operating scenarios. The proposed theoretical model-based technique determines ship angles in a wave collision and assesses sun-related angles concerning the vessel motions. Based on the panel angles, the solar irradiance and the PV system power variations can be derived. The developed method can simultaneously evaluate the effect of ship motions on the photovoltaic... 

This research presents an application of transparent lanthanum-modified lead zirconate titanate (PLZT) materials in micro light source tracking device, which is designed to function as a result of irradiation, having neither lead wires nor electric circuits. The focus of the paper is on the analytical and finite element investigation into ultraviolet photo-induced multi-physics responses of PLZT photocantilever and a comparison of the measured bending displacement to check the feasibility of these materials in design of micro light source tracking device. The finite element formulation of the transverse deflection for multi-physics analysis of PLZT ceramics by including the photovoltaic and... 

In this paper, a reliable low power single phase grid-connected inverter for photovoltaic modules is proposed. The inverter has improved lifetime since large electrolytic capacitor is replaced with small film capacitor due to circuit topology, power processing and proper control scheme. Thus the main limiting component in single phase grid connected inverters is obviated. The proposed inverter consists of two power processing stages. First a dual active bridge (DAB) converter boosts the voltage of PV panel to approximately 440 V and eliminates impact of high dc bus voltage ripples. A proper feed forward control is proposed to regulate the dc bus voltage with high ripple. Simulation results... 

The plasmonic effects of infiltrated silver (Ag) nanoparticles, with different contents, inside a nanostructured TiO2 film on the photovoltaic performance of dye-sensitized solar cells (DSSCs) are explored. The synthesized Ag nanoparticles are immobilized onto deposited TiO2 nanoparticles by a new strategy using 3-mercaptopropionic acid (MPA), a bifunctional linker molecule. Transmission electron microscope (TEM) images show that monodispersed Ag and polydispersed TiO2 nanoparticles have an average diameter of 12 ± 3 nm and 5 ± 1 nm, respectively. Moreover, Fourier transform infrared spectroscopy (FTIR) analysis reveals that Ag nanoparticles were successfully functionalized and capped with... 

Solution-processed quantum dots (QDs) have attracted significant attention for the low-cost fabrication of optoelectronic devices. Here, we synthesized PbS QDs via hot injection method and passivated the trap states by using short thiols and dopant elements for photovoltaic application. In order to study the effect of dopants on photovoltaic application, PbS QDs were doped by using three different cations: Cadmium, Calcium, and Zinc. We utilized Time resolvel Photoluminescence measurement to study the carriers lifetime for different samples and found that the carriers life time increases ∼80% by using Cd as a dopant compared with undoped sample. In addition, the results of J-V measurement... 

Solar energy will make a valuable contribution for power generation in the future. However the intermittency of solar energy has become an important issue in the utilization of PV system, especially small scale distributed solar energy conversion systems. The issue can be addressed through the management of production and storage of the energy in the form of hydrogen. The hydrogen can be produced by solar photovoltaic (PV) powered electrolysis of water. The amount of transferred energy to an electrolyzer from a PV module is a function of the distance between maximum power points (MPP) of PV module and the electrolyzer operating points. The distance can be minimized by optimizing the number... 

Superstrate configuration CuInS2 (CIS) solar cells are fabricated using a spray pyrolysis method. We avoided selenization process, cyanide etching and CdS buffer layer, to keep the process 'green'. CIS layers are formed by spray pyrolysis of an aqueous precursor ink containing metal chloride salts and thiourea at 350 °C. We investigated the effect of intentional Zn doping on structural, morphological and photovoltaic response of the fabricated CIS films by dissolving ZnCl2 in aqueous precursor solution. At a zinc doping level ranging between 0.25 and 1.00 mol%, Zn doping is found to improve the CIS crystal growth and surface morphology of CIS films. Compared with the performance of the... 

Solar cells with high efficiency, low cost, and high stability are the target for the new generation of solar cells. A fully printable perovskite (CH3NH3PbI3) solar cell (PSC) with device architecture FTO/TiO2/Al2O3/NiOx/C is fabricated in the current research as a low-cost and relatively stable structure and is investigated to determine how different fabrication factors such as the thickness of the insulating spacer layer (Al2O3) or treatments such as heat and UV-O3 treatments can affect the interfacial properties of this multilayer mesoporous structure. X-ray photoelectron spectra (XPS) show that UV-O3 treatment increases the Ni3+(Ni2O3) phase on the surface of the black nickel oxide layer... 

The fabrication of high performance, solution-processed CIGS family solar cells is based on high-temperature crystallization processes in chalcogen-containing atmosphere and/or using dangerous solvents like hydrazine. The non-hydrazine sulfurization- and selenization-free reports typically suffer from poor grain structures. We report a facile strategy to overcome grain growth limitations at very low temperature processing (250 °C). Selenium free Superstrate configuration CuInS2 (CIS) solar cells are fabricated using a nanocrystals ink which avoiding from high temperature selenization or/and sulfurization is targeted. We investigated the effect of intentional M doping (M = Sb, Zn, Cd and Sn)... 

Recent investigations on multifunctional piezoelectric semiconductors have shown their excellent potential as photovoltaic components in high-efficiency third-generation quantum nanostructure (QNS) solar cells. The current work is devoted to studying the electro-elastic behavior of high-density QNS photovoltaic semiconductors within which initial mismatch strains of arrays of quantum dots (QDs) or quantum wires (QWRs) induce coupled electro-mechanical fields. The inter-nanostructure couplings which are of great importance in high-density QNS arrays are incorporated in the presented analytical framework. In practice, QNSs with different geometries such as spherical, cuboidal, or pyramidal QDs... 

The purpose of the present study is to investigate the thermal performance of a photovoltaic/thermal system, integrated with phase change materials in porous medium. For this purpose, a metal foam was employed as porous medium and the performance of five different PCMs, as organic and inorganic, were examined as well. Moreover, the effects of different key parameters such as the mass flow rate, solar irradiance, inlet water temperature and inclination were studied. Finally, the simulation results were compared with a water-cooled photovoltaic/thermal without incorporating PCMs and porous medium, and thermal performance of the three PV/T cases were reported. The highest thermal efficiency of... 

This paper addresses a low complexity and high efficient cooling system applicable on photovoltaic (PV) system leading to enhance electrical efficiency and provide preheated water. The developed system consists of a photovoltaic panel, a cooling water system establishing a uniform surface temperature, and a solar water heater. According to the proposed system characteristics, the setup is constructed based on a single mono-crystalline solar panel to absorb more solar radiation intensity and generate more electrical energy per area in compare to a poly-crystalline panel. The preheated water produced by absorbed heat from the photovoltaic is conducted to a solar water heater to satisfy... 

Large-scale K-doped ZnO nanotapers were successfully grown on an indium tin oxide (ITO) substrate using a facile electrochemical route. The structural and morphologic analysis exhibited that the K-doped ZnO nanostructures had a nanotaper morphology and strong preferential [0001] c-axis direction with a hexagonal polycrystalline structure. The optical results show that the incorporation of K+ ions as the donors in a ZnO lattice leads to substantial modulation of the band gap structure of ZnO nanotapers, which results in a redshift in the ultraviolet emission peaks. The considerable enhancement of performance in K-doped ZnO-based dye-sensitized solar cells (DSSCs) can be related to the doping... 

This paper reports on the synthesis of ZnO nanowires (NWs), as well asthe compound nanostructures of nanoparticles (NPs) and nanowires (NWs+NPs) with different coating layers of NPs on the top of NWs and their integration in dye-sensitized solar cells (DSSCs). In compound nanostructures, NWs offer direct electrical pathways for fast electron transfer, and the NPs of ZnOdispread and fill the interstices between the NWs of ZnO, offering a huge surface area for enough dye anchoring and promoting light harvesting. A significant photocurrent density of 2.64mA/cm2 and energy conversion efficiency of 1.43% was obtained with NWs-based DSSCs. The total solar-to-electric energy conversion efficiency... 

In a nutshell, this study outlines the efficacy of mixed dimensional (2D/3D) hybrid perovskites by developing a new class of triple-cation quasi-2D perovskites having (S0.97S′0.03)2[Cs0.05(FA0.97MA0.03)0.95]n-1Pbn(I0.07Br0.03)3n+1 general composition, in which a mixture of ý5-ammonium valeric acid ýiodideý (S) and tetra-n-octylammonium ýbromide (S′) was employed ýas a spacer.ý The effect of the 2D and 3D structures molar ratios (i.e., C=2D/2D+3D) in the range of 0-100 % on photovoltaic performance of the deposited photoanodes was systemically studied. Drawing a comparison between such compounds and an analogous triple-cation 3D counterpart (i.e., Cs0.05(FA0.83MA0.17)0.95Pb(I0.83Br0.17)3) as...