Sharif Digital Repository

Background: Titanium (Ti) implants are commonly coated with hydroxyapatite (HA). However, HA has some disadvantages such as brittleness, low tensile strength and fracture toughness. It is desirable to combine the excellent mechanical properties of ZrO 2 and the chemical inertness of Al 2O 3 with respect to the purpose of this project which was coating Ti implants with HA-ZrO 2-Al 2O 3 to modify the surface of these implants by adding ZrO 2 and Al 2O 3 to HA. The purpose of this study was to evaluate the efficacy of hydroxyapatite coating nonocomposite. Methods: From September 2009 to January2011, functionally graded HA-Al 2O 3-ZrO 2 and HA coatings were applied on Ti samples. HA-Al 2O 3-ZrO... 

A silicon carbide coating was formed on the surface of graphite flakes by reaction of molten Si with carbon at 1100-1300. °C in a 95%KCl-5%NaF molten salt under Ar atmosphere. The effect of temperature and Si/graphite ratio in the initial mixture on the quality and the amount of SiC were investigated by XRD and SEM/EDS analyses. Also, the water wettability, oxidation resistance and zeta potential of un-coated and coated graphite were examined by TGA analysis and sedimentation test. The results show the amount of coating to increase in the coated flakes with increasing temperature and Si/graphite ratio. The SiC coating improves water wettability of graphite and acts as a protective layer to... 

Due to its high discharge capacity, low cost, and good safety, LiNi0.5Co0.2Mn0.3O2 (NCM 523) is regarded as a promising cathode material for the next-generation of lithium-ion batteries. However, poor cycling stability and rate capability are the main disadvantages of the NCM 523 cathode material. In this work, SiO2 single layer-coated and reduced graphene oxide (outer)/SiO2 (inner) double layer-coated NCM 523 have been prepared by a facile wet chemical method. Field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) analysis, transmission electron microscopy (TEM), Raman spectroscopy and Fourier transform infrared (FTIR) spectroscopy results confirm that NCM 523... 

A headspace solid-phase microextraction (HS-SPME) method was developed for the trace determination of geosmin in water and apple juice samples. A poly(dimethylsiloxane) (PDMS) fiber was synthesized as coated fiber using sol-gel methodology. After performing the extraction in the headspace, the fiber was introduced directly into the injection port of a gas chromatography-mass spectrometry (GC-MS) using electron impact (EI) ionization mode. One-at-the-time optimization strategy was applied to investigate and optimize important extraction parameters such as extraction temperature and time, ionic strength, headspace volume, and desorption temperature and time. The analytical data exhibited an... 

Green's functions of a transversely isotropic half-space overlaid by a thin coating layer are analytically obtained. The surface coating is modeled by a Kirchhoff thin plate perfectly bonded to the half-space. With the aid of superposition technique and employing appropriate displacement potential functions, the Green's functions are expressed in two parts; (i) a closed-form part corresponding to the transversely isotropic half-space with surface kinematic constraints, and (ii) a numerically evaluated part reflecting the interaction between the half-space and the plate in the form of semi-infinite integrals. Some limiting cases of the problem such as surface-stiffened isotropic half-space,... 

This paper presents a study of the Taguchi design method to optimise the rate of electrophoretic deposition (EPD) of Bioglass® particles from aqueous suspensions. The effect of Bioglass® concentration, pH and electric field was investigated. An orthogonal array of L16 type with mixed levels of the control factors was utilized. Multivariate analysis of variance (MANOVA) and regression analysis based on the partial least-square method were used to identify the significant factors affecting the deposition rate and its stability during constant-voltage EPD. It was found that the pH of the suspension significantly influences the deposition rate whereas the applied electric field has the smallest... 

Functionally graded composite coatings constitute a class of materials which are mostly used for mechanical and tribological applications. Among these materials, nickel metal deposits with incorporation of SiC particles have excellent mechanical properties due to nickel metal and good tribological properties due to the SiC particles. In this work, nickel coatings containing different sizes of SiC particles, nanoparticles and microparticles (10 nm to 5 μm), were electrodeposited from an additive-free sulfate bath containing nickel ions and SiC particles. The material properties of the coatings were compared to nickel coatings containing microparticles (5 μm). The effect of current density,... 

In the present work, the hot corrosion behavior of two types of multilayer plasma sprayed TBC were investigated and compared with functionally graded and conventional TBCs. These kinds of multilayer coatings consisted of nano/μ alumina as a top coat on YSZ layer, a metallic bond coat and a functionally graded intermediate layer deposited between YSZ and bond coat layers. All the layers were sprayed on the Ni-base super alloy substrate. The hot corrosion resistance of the plasma sprayed coatings was examined at 1050 °C for 40 h, using a fused mixture of 45 wt% Na2SO4 + 55wt%V2O5. Before and after hot corrosion, the microstructure and phase analysis of the coating were studied using scanning... 

Abstract: This work describes coating of NiCoCrAlY on IN-738LC superalloy by high-velocity oxygen fuel (HVOF) process. Properties of the coatings are significantly influenced by oxygen/fuel ratio and other spraying parameters. The effect of oxygen/fuel ratio on the oxidation behavior, bond strength, hardness, roughness and microstructure including porosity, inclusion formation and unmelted particles are discussed here. The porosity and inclusion in C1 coating are maximal. C2 coating with oxygen/fuel ratio of 2 has the highest bond strength and the lowest unmelted particles. C3 coating with the lowest total porosity and inclusion has the minimal roughness and the highest oxidation resistance... 

This work describes coating of NiCoCrAlY on IN-738LC superalloy by high-velocity oxygen fuel (HVOF) process. Properties of the coatings are significantly influenced by oxygen/fuel ratio and other spraying parameters. The effect of oxygen/fuel ratio on the oxidation behavior, bond strength, hardness, roughness and microstructure including porosity, inclusion formation and unmelted particles are discussed here. The porosity and inclusion in C1 coating are maximal. C2 coating with oxygen/fuel ratio of 2 has the highest bond strength and the lowest unmelted particles. C3 coating with the lowest total porosity and inclusion has the minimal roughness and the highest oxidation resistance and... 

The dissolution of plasma-sprayed hydroxyapatite (PHA) coatings with different characteristics, produced by various spraying conditions, in a Tris-buffered solution at pH 7.4 was experimentally studied through the measurement of the release of calcium ions. The phase composition of the coatings at surface and interface, and the porosity were evaluated. The analytical modeling revealed that the calcium dissolution process was composed of two stages. The first stage was found to be both surface and diffusion controlled. The second stage was an exactly diffusion-controlled dissolution. In the first stage, the rate of dissolution and the solubility of the coatings with minimum contents of... 

Apatite-coated Ag/AgBr/TiO2 was prepared by deposition of Ag as novel metal to generate electron-hole pairs by extending the excitation wavelength to the visible-light region, AgBr, and hydroxy apatite as photosensitive material and adsorption bioceramic, respectively. The energy dispersive X-ray spectrometry clearly showed the presence of Ti, Ag, Ca, and P elements on the surface of catalyst. The bactericidal experiments in dark media indicated that only the novel catalyst shows inhibiting growth of bacteria in this case. A transmission electron microscopy image illustrated that catalyst nanoparticles adhere to the outer membrane of the cell and act as an inhibitor to the nourishment of... 

Nowadays, the LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material has attracted great research interest due to its high energy density and less usage of costly raw materials. However, the high nickel content of NCM811 brings about an extremely unstable interface between the electrode and electrolyte and therefore inferior cyclic stability. Herein, we have proposed a straightforward method to deliver 1, 2, and 4 wt % of TiO2 nanoparticles (NPs) on the surface of the NCM811 cathode material and to improve its properties at room and high temperatures. Based on scanning electron microscopy and transmission electron microscopy observations, the coating thickness varies from 10 to 35 nm and the 2 wt %... 

Ni-Co/SiC nanocomposite coatings were electrodeposited in a modified watt type of Ni-Co bath containing 20 nm SiC particles to be codeposited. Potentiodynamic polarization tests were conducted to study the effect of the SiC particulates on the electrodeposition of Ni and Co. Scanning electron microscopy was used to assess the morphology of the Ni-Co alloy and Ni-Co/SiC nanocomposite coatings. The distribution of the particulates in the matrix was considered by means of transmission electron microscopy. Applying nanomechanical testing instruments coupled to atomic force microscopy, mechanical properties of the alloy and composite coatings were studied and compared. The presence of 11 vol.%... 

This review is mostly focused on the recently emerged methodologies for preparing the appropriate extracting media with enhanced capacity, stability and selectivity, which could be used in capillary microextraction (CME). We particularly consider conductive polymers, sol-gel-based materials, monolithic coatings, molecularly-imprinted polymers and xerogels. Moreover, we discuss recent advances in configuration of CME, array capillaries and unbreakable substrates  

An aniline-based polymer was electrochemically prepared and applied as a new fiber coating for solid phase microextraction (SPME) of some priority phenols from water samples. The polyaniline (PANI) film was directly electrodeposited on the platinum wire surface in sulfuric acid solution using cyclic voltammetry (CV) technique. The efficiency of new coating was investigated using a laboratory-made SPME device and gas chromatography with flame ionization detection for the extraction of some phenols from the headspace of aqueous samples. The scanning electron microscopy (SEM) images showed the homogeneity and the porous surface structure of the film. The results obtained proved the ability of... 

A solution of polyamide (PA) containing polyethylene glycol (PEG) as a side low-molecular-weight polymer was electrospun. After synthesizing the PA-PEG nanofibers, the constituent was subsequently removed (modified PA) and confirmed by Fourier transform infrared spectroscopy. The scanning electron microscopy images showed an average diameter of 640 and 148 nm for PA and PA-PEG coatings, respectively, while the latter coating structure was more homogeneous and porous. The extraction efficiencies of PA, PA-PEG, and the modified PA fiber coatings were assayed by headspace solid-phase microextraction of a number of chlorophenols from real water samples followed by their determination by gas... 

Superparamagnetic Iron Oxide Nanoparticles (SPIONs) were synthesized and coated with pseudopolyrotaxanes (PPRs) and proposed as a novel hybrid nanostructure for medical imaging and drug delivery. PPRs were prepared by addition of α-cyclodextrin rings to functionalized polyethylene glycol (PEG) chain with hydrophobic triazine end-groups. Non-covalent interactions between SPIONs and PPRs led to the assembly of SPIONs@PRs hybrid nanomaterials. Measurements of the 1H Nuclear Magnetic Resonance (NMR) relaxation times T1 and T2 allowed us to determine the NMR dispersion profiles. Comparison between our SPIONs@PRs hybrid nano-compound and the commercial SPION compound, Endorem®, showed a higher... 

Solid-phase microextraction (SPME) is a fast, solvent-free technique, which, since its introduction in the 1990s, has been increasingly applied to sample preparation in analytical chemistry. Conventional SPME fibers are fabricated by making a physical bond between the usual silica substrate and the polymeric coatings. However, some applications are limited, as the lifetime and the stability of conventional SPME fibers cannot meet the demands of analyzing relatively non-volatile compounds with more polar moieties. There have been attempts to analyze less volatile compounds by increasing the thermal, physical and chemical stability of the fibers. In this review, we present some new... 

The effects of leachate recycling and bed mixing on the removal rate of H 2S from waste gas stream were investigated. The experimental setup consisted of an epoxy-coated three-section biofilter with an ID of 8cm and effective bed height of 120cm. Bed material consisted of municipal solid waste compost and PVC bits with an overall porosity of 54% and dry bulk density of 0.456gcm -3. Leachate recycling had a positive effect of increasing elimination capacity (EC) up to 21gSm -3 bedh -1 at recycling rates of 75mld -1, but in the bed mixing period EC declined to 8g Sm -3bedh -1. Pressure drop had a range of zero to 18mm H 2Om -1 in the course of leachate recycling. Accumulation of sulfur reduced...