Sharif Digital Repository

Porous silicon samples are obtained by electrochemical method on n-type wafers in room light. Scanning electron microscopy showed that the porous structure consisted of macropores under a thin microporous layer. Placing the samples in Pd-electroless solution causes the crakes inside the microporous layer and growth of the palladium particles in these crakes. However, removing the microporous layer by KOH solution with an ultrasonically assisted process makes the growth of rather uniform palladium particles on the surface in electroless plating. Variation of the electrical resistance in the presence of diluted hydrogen at room temperature revealed that the best samples have the ability to... 

Porous silicon samples were obtained by the electrochemical method and were impregnated with Pd by the electroless process. X-ray photoelectron spectroscopy illustrated that the surface of the samples is oxidized during the palladium deposition. Scanning electron microscopy showed how factors such as morphology and pre-oxidations of porous samples and the plating parameters including Pd-salt concentration, HCl concentration, temperature of the electroless solution and the time of process affect the growth and nucleation of Pd particles. Observations demonstrated that the illumination-assisted process on p-type samples has a drastic effect on the growth of palladium. Hydrogen sensing of these... 

Porous poly-silicon (PPS) samples, obtained by electrochemical anodization of p-type poly-silicon wafers, were doped with Pd by the electroless process. Rutherford backscattering spectroscopy shows that Pd has diffused a few micrometres into the PPS layer. Scanning electron microscopy and energy dispersive x-ray analysis results demonstrate the presence of Pd as dispersed clusters on the surface. The variation of the electrical resistance in the presence of dry air diluted with hydrogen at room temperature shows that Pd/PPS samples have the ability to sense hydrogen at levels down to several thousands of ppm. This value is far below the flammability limit of hydrogen gas. It was found that... 

This paper reports on hydrogen sensing based graphene oxide hybrid with Co-based metal organic frameworks (Co-MOFs@GO) prepared by the hydrothermal process. The texture and morphology of the hybrid were characterized by powder x-ray diffraction, scanning electron microscopy and Brunauer-Emmett-Teller analysis. Porous flower like structures assembled from Co-MOFs and GO flakes with sufficient specific surface area are obtained, which are ideal for gas molecules diffusion and interactions. Sensing performance of Co-MOFs@GO were tested and also improved by sputtering platinum (Pt) as a catalyst. The Pt-sputtered Co-MOFs@GO show outstanding hydrogen resistive-sensing with response and recovery... 

The potential of hydrogen (pH) is a basic and critical parameter representing the function of numerous chemicals/biomolecules. Due to the widespread applications of pH in diverse fields, the development of rapid and simple yet reliable probes for the determination of pH has attracted significant interest. In this paper, by using AuNRs, silver ions, and ascorbic acid as colorimetric pH sensor, a multicolorimetric nanosensor is described for pH measurement. The reduction of silver ions by ascorbic acid which is strongly influenced by pH, results in silver nanoshell deposition on the surface of AuNRs. Consequently, the formation of Au@Ag core-shell NRs causes a series of blue shifts in the... 

In this article we report hydrogen sensing property of WO 3/MWNTs thin films that were fabricated by spin-coating on alumina substrates. The MWNTs were initially functionalized (f-MWNTs) to enhance dispersion in the sol of multiwalled carbon nanotubes (MWNTs) and tungsten trioxide (WO 3). Microstructure, morphology and chemical composition of the materials were characterized by SEM, TEM, XRD and XPS methods. Our results show WO 3 nanoparticles were nucleated on oxygenated group on surface of f-MWNTs in hybrid suspension. After annealing the films at 350 °C, electrical conductance measurements at different operating temperature were performed and the results indicates rather fast and linear... 

Porous silicon (PS) is widely utilized in gas sensors. Palladium is a good choice to sensitize the surface of PS to hydrogen. Ideally for highest sensitivity of the sensor, all the pores of PS should be completely covered with palladium. Rutherford backscattering spectroscopy (RBS) technique is routinely used to determine depth profile of elements in thin layers. By using microbeam analysis as a complementary technique, we clearly observed the lateral image of penetrated Pd in depth. In this work, we used electrochemically anodized-silicon wafer doped with Pd by the electroless process. In our analysis, we intentionally characterized both the area of PS where Electric Field is applied during... 

Pd doped WO3 fibers were synthesized by electro-spinning. The sol gel method was employed to prepare peroxopolytungstic acid (P-PTA). Palladium chloride and Polyvinyl pyrrolidone (PVP) was dissolved in the sol Pd:WO3 = 10% molar ratio. The prepared sol was loaded into a syringe connected to a high voltage of 18.3 kV and electrospun fibers were collected on the alumina substrates. Scanning electron microscope (SEM), X-ray powder diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) techniques were used to analyze the crystal structure and chemical composition of the fibers after heat treatment at 500 °C. Resistance-sensing measurements exhibited a sensitivity of about 30 at 500 ppm... 

Tungsten trioxide has been prepared by using P-PTA as a precursor on alumina substrates by spin coating method. Palladium introduced on WO 3 film via electrolysis deposition by using palladium chloride as catalytic precursor. The catalytic precursor was introduced on the series of films with different morphologies. X-ray diffractometry (XRD), Scanning electron microscopy (SEM) and XPS were applied to analyze structure and morphology of the fabricated thin films. Then we measured variation of samples' electrical conductivity of pure and Pd added films in air and diluted hydrogen. Addition of Pd resulted in a remarkable improvement of the hydrogen sensing properties of WO 3 by detection of... 

The sol gel method was employed to prepare peroxopolytungstic acid (P-PTA). Palladium chloride salt was dissolved in the sol with different Pd:W molar ratios and coated on Al2O3 substrates by spin coating method. XRD and XPS techniques were used to analyze the crystal structure and chemical composition of the films before and after heat treatment at 500 °C. We observed that Pd can modify the growth kinetic of tungsten trioxide nanoparticles by reducing the crystallite size and as a result can improve hydrogen sensitivity. Resistance-sensing measurements indicated sensitivity of about 2.5 × 104 at room temperature in hydrogen concentration of 0.1% in air. Considering all sensing parameters,... 

Nowadays, gasochromic Pd/WO3 coatings as optically switchable materials have become more applicable for hydrogen sensors and smart windows. In this study, WO3 films were prepared by Pulsed Laser Deposition (PLD) and spin-coating sol-gel techniques. For deposition of Pd, first a layer of PdCl2 was obtained via a simple drop-drying process by dropping PdCl2 solution onto WO3 substrates and drying them at room temperature. Then Pd nanoparticles were synthesized via hydrogen gas exposure that causes reduction of the PdCl2 layer. According to Scanning Electron Microscope (SEM) observations before hydrogen reduction, many individual nanoparticles or fractal-like constructions of palladium were...