Sharif Digital Repository

In this research convective heat transfer coefficient enhancement of nanofluids prepared from high surface area graphene has been investigated in laminar flow in the developing region. The nanofluid has been prepared from nanoporous graphene with high surface area and with concentration of 0.025 to 0.1 wt.%. Deionized water has been used as the base fluid and a type of Ter-Polymer has been utilized as the surfactant. The results indicate that thermal conductivity of nanofluid with concentration of 0.1 wt.% remains quite constant, with only 3.8% enhancement, while convective heat transfer coefficient improves significantly, with 34% enhancement. The behavior of this enhancement related to the... 

Co-Mo/Graphene composite synthesized for the first time through the spray pyrolysis method and applied as an HDS catalyst to produce a sulfur free Naphtha feed. The major advantage of the spray pyrolysis technique was its concurrent capability of the in-situ and simultaneous Co-Mo deposition upon the graphene. The produced material was characterized through the XRD, BET-BJH, FTIR and Raman spectroscopy as well as; the NH3-TPD, TPR, TEM and FESEM techniques. The prepared catalyst showed unique properties such as; high degree of total acidity of 5.1 (vs. the usual 0.2–2.0) mmole NH3/g-cat and a relatively high surface area of 705 vs. 189 m2/g of the commercial material. Furthermore, the... 

In this study, dynamic adsorption behavior of different gaseous volatile organic compounds (VOCs) on a new modified M-MIL-101(Cr) was investigated with a great emphasis on gasoline adsorption. The M-MIL-101(Cr) was synthesized, along with comprehensive purification procedures, using a new linker to cluster molar ratio (2:1 instead of 1:1) and different modulators (i.e. HF and HNO3). All prepared adsorbents were characterized by XRD, FTIR, FE-SEM and N2 adsorption-desorption at 77 K. The results showed that surface area and pore volume of the M-MIL-101@Free (i.e. modified MIL-101(Cr) with using any modulator) which were 4293 m2/g and 2.43 cm3/g, greatly elevated up to 37.2% and 71.6% against... 

A task-specific Brønsted acidic ionic liquid (BAIL), 1-benzyl-3-methylimidazolium hydrogensulfate ([BnMIm]HSO4), was prepared and confined onto the high surface area silica gel. The catalyst has shown extraordinary activity in comparison of homogeneous ionic liquid (IL) system for Fischer esterification of fatty acid with ethanol. The ester derivatives were synthesized in high yields and catalyst was easily separated from the reaction mixture by simple filtration. The structure of the catalyst is theoretically modelized to investigate the unusual catalytic activity. Hence, a hydroxylated cage-like nano-cluster, H6Si8O12(OH)2, was selected to mimic the surface of silica gel. The interactions... 

In this study a novel Pt/Ni nanostructure consisting of nano-bushes and nanocubes was fabricated onto TiO 2 nanotubes. The scanning electron microscopy images showed that a large amount of well-dispersed nano-architectures had uniformly covered all over the surface which made an electrode with high surface area. It was obviously seen that the nanocube structures mainly consists of Ni had been grown on top of each other while the Pt colonies represented bush-like structures. As a non-enzymatic glucose biosensor, the Pt/Ni TiO 2 nanotubes modified electrode exhibited an excellent performance. The proposed biosensor had two linear ranges for detection of glucose from 0 to 0.12 mM (correlation... 

Processing conditions and final mechanical properties of polymer nanocomposites are affected by their interfacial layers behavior. However, it is impossible to determine directly the properties of these layers by dynamic rheometry tests. In this work, the interfacial layers properties are evaluated for polystyrene containing silica nanoparticles by the concept of glass-transition temperature shift. The samples were prepared via solution-mixing method and dynamic rheometry was used to determine the viscoelastic behavior of filled polymers in the melt state. This initial step showed that addition of silica particles increased the glass-transition temperature. By preference, decrease in the... 

Galvanostatic method was used to electrodeposit Fe nanostructures on platinum electrodes as catalysts. Scanning electron microscopy (SEM) revealed flower-like Fe deposits with high surface area. Carbon nanotubes were grown on flower-like Fe nanostructures by chemical vapor deposition. The structure of the synthesized carbon nanotubes was investigated by scanning electron microscopy, transmission electron microscopy, Raman spectroscopy and X-ray diffraction. According to X-ray diffraction patterns, Fe was the only detected constituent of the deposited coating. The carbon nanotubes had small wall-thickness and wide hollow core  

Coating of graphite flakes with MgO/carbon nanocomposite was carried out via gaseous state reaction between mixture of Mg metal, CO gas and graphite flakes at 1000 °C. XRD and FE-SEM analysis of coating showed that the coating was comprised of MgO nano particles and amorphous carbon distributed smoothly and covered the graphite surface evenly. Thermodynamic calculations were employed to predict the reaction sequences as well as phase stability. The effect of coating on water wettability and oxidation resistance of graphite was studied using contact angle measurement and TG analysis, respectively. It was demonstrated that the reaction between Mg and CO could result in MgO/C nanocomposite... 

TiO2 deposited on a membrane of Ag fibers was prepared as a photoelectrochemical cell electrode. Ag fibers were made by reduction of Ag complexes on cellulose fibers, followed by burning out the template. TiO 2 photocatalyst layers were grown on the fibers by electrophoretic deposition of TiO2 nanoparticles. Ag fibers could be uniformly deposited. Photocatalytic tests by dye decomposition and electrochemical impedance spectroscopy (EIS) under UV illumination demonstrate that Ag fibers act as a good substrate that provides both high surface area and good separation of photogenerated electron-hole pairs and causes the enhancement of photocatalytic activity in comparison with a thin film of... 

Hierarchical submicrometer TiO 2 hollow spheres with outer diameter of 300-700 nm and shell thickness of 200 nm are synthesized by liquid phase deposition of TiO 2 over carbon microspheres as sacrificial templates. The final TiO 2 hollow spheres are applied as a scattering layer on top of a transparent nanocrystalline TiO 2 film, serving as the photoanode of a dye-sensitized solar cell (DSC). In addition to efficient light scattering, the mesoporous structure of TiO 2 hollow spheres provides a high surface area, 74 m 2/g, which allows for higher dye loading. This dual functioning suggests that TiO 2 hollow spheres may be good replacements for conventional TiO 2 spheres as scatterers in DSCs.... 

Iron oxide nanoparticles, γ-Fe2O3NP, were deposited onto the surface of multi-walled carbon nanotubes and CNT/γ-Fe2O3NP hybrid nanomaterials were obtained. Then linear-dendritic ABA type block copolymers consisting of polyethylene glycol as B block and poly(citric acid) as A block, PCA-PEG-PCA, were synthesized and cisplatin (cis-diamminedichloroplatinum (CDDP) - a platinum-based chemotherapy drug) was conjugated with their carboxyl functional groups and CDDP/PCA-PEG-PCA anticancer prodrugs were prepared. Noncovalent interactions between CDDP/PCA-PEG-PCA anticancer prodrugs and CNT/γ-Fe2O3NP hybrid nanomaterials led to CDDP/PCA-PEG-PCA/CNT/γ-Fe2O3NP drug delivery systems. There are several... 

A simple and efficient method was developed for fabricating spherical granules of CuO catalyst via a three-step procedure. In the first step, copper oxide nanoparticles were synthesized by hydrothermal decomposition of copper nitrate solution under supercritical condition. Then, they were immobilized in the polymeric matrix of calcium alginate, and followed by high-temperature calcination in an air stream as the third step, in which carbonaceous materials were oxidized, to result in a pebble-type catalyst of high porosity. The produced CuO nanoparticles were characterized by transmission electron microscopy (TEM) that revealed an average size of 5 nm, X-ray diffractometry (XRD), and thermo... 

Herein, we report a new strategy for improving the efficiency and reducing the fabrication cost of dye-sensitized solar cells (DSCs) by elimination of the three- or four-fold layer deposition of TiO2. This is performed by replacing a single layer deposition of mesoporous TiO2 beads, with sub-micrometer size, high surface area and tunable pore size, synthesized by a combination of sol-gel and solvothermal methods. Furthermore, superior electronic properties gained by a reduction in electronic trap states are achieved through doping of pristine TiO2 beads with lithium. The beads have a spherical shape with monodispersed texture consisting of anatase-TiO2 nanocrystals and ultra-fine pores. The... 

A new facile strategy for fabrication of high surface area electrode in the form of mixtures of coated carbon nanotubes (CNTs) and TiO2 nanoparticles with various weight ratios is reported. The so-called polymeric gel process was used to deposit thick film containing uniform distribution of TiO2 nanoparticles and coated CNTs with high porosity by dip coating for dye-sensitized solar cells (DSSCs) applications. Based on simultaneous differential thermal analysis, the minimum annealing temperature to obtain inorganic- and organic-free films was determined at 500°C. X-ray diffraction analysis revealed that deposited films were composed of primary nanoparticles with crystallite size in the range... 

A novel simple synthetic procedure for fabrication of high surface area nanostructured TiO2 electrode with uniform particles for photovoltaic application is reported. Modifying the TiO2 particulate sol by pH adjustment together with employment of a polymeric agent, so-called polymeric gel process, was developed. The polymeric gel process was used to deposit nanostructured thick electrode by dip coating incorporated in dye-sensitized solar cells (DSSCs). X-ray diffraction (XRD) analysis revealed that deposited film was composed of primary nanoparticles with average crystallite size in the range 21-39 nm. Field emission scanning electron microscope (FE-SEM) images showed that deposited film... 

A new method based on the combination of magnetic solid phase extraction (MSPE) and spectrofluorimetric determination was developed for isolation and preconcentration of fluoxetine form aquatic and biological samples using sodium dodecyl sulfate (SDS) coated Fe 3O 4 nanoparticles (NPs) as a sorbent. The unique properties of Fe 3O 4 NPs including high surface area and strong magnetism were utilized effectively in the MSPE process. Effect of different parameters influencing the extraction efficiency of fluoxetine including the amount of Fe 3O 4 and SDS, pH value, sample volume, extraction time, desorption solvent and time were optimized. Under optimized condition, the method was successfully... 

Arrays of ZnO nanorods were synthesized on ZnO seed layer/glass substrates by a hydrothermal method at a low temperature of 70 °C. The effect of pH > 7 of the hydrated zinc nitrate-NaOH precursor on the morphology and topography (e.g. size, surface area and roughness), the optical characteristics (e.g. optical transmission and band-gap energy), hydrophilicity and antibacterial activity of the grown ZnO nanostructure and nanorod coatings were investigated. For pH = 11.33 of the precursor (NaOH concentration of 0.10M), a fast growth of ZnO nanorods on the seed layer (length of ∼1 νm in 1.5 h) was observed. The fast growth of the ZnO nanorods resulted in a significant reduction in the optical... 

A template-directed synthetic method, using surfactant cetyltrimethylammonium bromide (CTAB) as a template and co-surfactant polyethylene glycol (PEG600) as a co-template under hydrothermal conditions, has been applied to obtain dandelion-like HAp. The morphology, size, crystalline phase, chemical composition, physical characteristics, and thermal behavior of the product were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), Fourier ransform infrared spectroscopy (FTIR), induced coupled plasma spectroscopy (ICP), BET (Brunauer, Emmett, and Teller) method, and simultaneous thermal analysis (STA). SEM and TEM...