Sharif Digital Repository

A literature review on the studies and applications of heat pipe heat exchanger in air conditioning systems in recent years is conducted. The related papers were grouped into two main categories and a summary of experimental and theoretical studies is presented. Based on this investigation, the application of a heat pipe heat exchanger or a thermosyphon heat exchanger in the conventional air conditioning systems is recommended as an efficient means for energy savings and dehumidification enhancement to maintain acceptable room conditions. This review shows that the literature on the application of heat pipe heat exchangers in air conditioning systems is very limited. Therefore, much more... 

In this paper, entropy generation in heat exchangers used in Indirect Evaporative Coolers (IDECs) is studied. First, expressions for the rate of entropy generation in tube-type and plate-type cross-flow heat exchangers used as IDECs are obtained. Then, by introducing appropriate geometric constraints and employing thermohydraulic design equations, the variation of the rate of entropy generation within the heat exchangers is investigated. The maximum EER, outlet temperatures and the optimum sizes are obtained for several cases. The results of several experiments conducted on an optimum tube-type experimental prototype are presented and compared with the numerical data. Copyright © 2009... 

In this study, the optimal location of baffle in the header of air-to-air plate heat exchangers and the geometry of the header and the effects of triangular fins arrays on the effectiveness were numerically investigated for different flow rates and Reynolds numbers on different models. The main purpose of inlet baffle and geometry changes is to improve the pattern of flow distribution and assist flow uniformity. The investigations show that the optimal location of the inlet baffle with high Reynolds numbers has an insignificant effect on effectiveness, while with Reynolds numbers 250-3000, the effectiveness is affected significantly by baffle location. On the other hand, the reduction in... 

In this paper, an analytical model is presented for forced convective film condensation inside smooth vertical tubes, in which Prandtl mixing length theory, Van Driest hypothesis and Reynolds analogy are used. Comparison of this model with the available experimental data and three other correlations reported in the literature demonstrates that the results are in satisfactory and close agreement  

It is believed that it is going to be a sizeable mismatch between supply and demand when it comes to renewable resources. Lately, researchers are on course to compensate for the unpredictabilityof such resources by the employment of phase change materials (PCMs). Having multiple advantages, PCMs generally suffer from inadequate thermal conductivity which causes prolonged transition procedures. To tackle this issue, this study is fixated on two parameterswhich are linked to fins addition and porous media incorporation in a melting process within a triple concentric tube heat exchanger (TCTHX). The results provided by multiple cases underlined the significance of natural convection in the bare... 

Horizontal Ground Heat Exchangers (HGHE) as a means of exploiting geothermal energy has come to the fore for a few decades. Various analytical and Computational Fluid Dynamics (CFD) methods have been proposed to predict the performance of the HGHEs. The available analytical approaches are fast; however, they are based on various simplifications and assumptions, affecting their accuracy. On the other hand, CFD methods are more accurate, but their computational cost is a burden. Therefore there is an acute need for an accurate and fast method for predicting the long-term performance of HGHEs. To this aim, this study puts forward a novel hybrid analytical-numerical model for predicting the... 

Compact heat exchangers are among the vital components used in various industries. In this study, a general framework has been developed with a multi-scale point of view for three-dimensional simulation of multi-stream plate-fin heat exchangers. The most important features in the MSPFHEs simulation, such as phase change phenomena, multi-component mixtures, multiple streams, transversal, lateral and longitudinal conduction, non-uniformity of inlet flow, variable fluid properties, and heat leakage are simultaneously considered in this model. The modular form of the model structure has facilitated layer-by-layer simulation of cross flow heat exchangers as well as parallel flow ones. Our model... 

This work is dedicated to finding a suitable measure to judge thermal performance of nanofluids. The importance of this issue arises from misleading claim of excess heat transfer of nanofluids compared to the base fluid, neglecting the hydraulic effects such as increase in pressure drop. To clarify the issue, the experimental setup with capability to create constant Reynolds number and constant pumping power is constructed. Thermal behavior of nanofluids of silicon oxide/water and aluminum oxide/water and distilled water in developing region of laminar flow regime is investigated. In this regard, the convective heat transfer coefficient within the finned tube heat exchanger is evaluated.... 

A numerical study has been performed to investigate the flow and heat transfer characteristics of fluid flow through heat exchanger tubes fitted with perforated conical rings. The holes are circular, and the number of holes N is ranged from 0 to 10. The influences of perforated conical ring diameter ratios D2/D1=0.4,0.5and0.6 and the hole diameter ratios d/D=0.06,0.1and0.14 on average Nusselt number, friction factor and thermal performance factor are reported. This analysis is performed in the turbulent flow regime 4000⩽Re⩽14,000 and the governing equations are solved by using (RNG) k-∊ model. Due to strong turbulent intensity, perforated conical rings lead to more flow perturbation and... 

Multi-stream Plate-fin heat exchangers (MSPFHEs) are among the most efficient heat exchangers in energy-based industries. They should be carefully designed to have maximum effectiveness and to avoid wasting energy. Flow maldistribution could significantly degrade the performance of heat exchangers. This study presents a novel modeling framework to capture the thermally-induced maldistribution in two-phase MSPFHEs. The developed model is used to show how thermally-induced flow maldistribution affects the performance of the heat exchanger, and some possible modifications are investigated to reduce its consequences. Our case study results show that thermally-induced maldistribution decreases... 

A fluctuation relation for the heat exchange of an open quantum system under a thermalizing Markovian dynamics is derived. We show that the probability that the system absorbs an amount of heat from its bath, at a given time interval, divided by the probability of the reverse process (releasing the same amount of heat to the bath) is given by an exponential factor which depends on the amount of heat and the difference between the temperatures of the system and the bath. Interestingly, this relation is akin to the standard form of the fluctuation relation (for forward-backward dynamics). We also argue that the probability of the violation of the second law of thermodynamics in the form of the... 

Horizontal ground heat exchangers (GHEs) have a lower initial installation cost in comparison to vertical ones; however, they require more land area. In order to reduce the required land area of horizontal GHEs, their heat exchange rate per unit land area needs to be enhanced. A remedy to this problem is installing horizontal GHEs in an arrangement with maximum heat exchange rate per unit land area. However, such arrangements have not been introduced for different types of horizontal GHEs thus far. To this end, in this study, the thermal performance of various GHE pipe arrangements for three different types (linear, spiral, and slinky) of horizontal GHEs is evaluated. Comparing the obtained... 

In this Study, radiator performance for passenger car has been studied experimentally in wide range of operating conditions. Experimental prediction of Nusselt number and heat transfer coefficient for coolant in radiator tubes are also performed with ε-NTU method. The total effectiveness coefficient of radiator and heat transfer coefficient in air side is calculated via try and error method considering experimental data. The Colburn factor and pressure drop are also estimated for this heat exchanger. Examples of application demonstrate the practical usefulness of this method to provide empirical data which can be used during the design stage. Copyright © 2006 by ASME  

Turbulent fully developed periodic condensation heat transfer and pressure drop in herringbone-type plate heat exchangers for R134a and steam were numerically investigated. A mixture model was introduced and the equations governing the two phase flow were simplified. Thus a single phase periodic flow with mixture properties was solved for R134a. For Steam a separate empirical model was used. The governing equations were solved numerically by a finite-volume method for elliptic flows in complex geometries using collocated variable arrangement. The influence of mass flux and vapor quality on frictional pressure drop for refrigerant was investigated. The heat transfer was studied using a...