Sharif Digital Repository

Pure and Pd-doped WO3 Nanocrystalline tungsten oxide films on alumina substrates were prepared via sol-gel method from peroxopolytungstic acid. AFM, XRD, SEM, XPS methods were used to determine the surface morphology, grain size and layer composition. XRD analysis showed WO3 nanocrystalline particles in monoclinic phase and with average size of about 333nm, which was consistent with SEM analysis results. Sensing properties of samples toward H2 gas was studied. The sensitivity of WO3 nanocrystalline films was about 4 at 2300ppm (0.2%) H2 gas. Introducing Pd to the system led to an increase in the sensitivity about 2 orders of magnitude. The sensitivity of Pd: WO3 was about 400 at 2300ppmH2  

In this paper, the performance of the benzene gas detection sensor in the air is optimized by an experimental design method. So in this work, Nanostructured thin films of ZnO and Zn2SnO4 were prepared in wurtzite form via a facile atmospheric pressure chemical vapor deposition (CVD) method, using metallic zinc and tin precursors. Characterization of the gas sensor was performed by using Powder X-ray diffraction (PXRD), scanning electron microscopy (SEM) and surface area analysis (using BET method). The results show that Zn2SnO4 nanowire network exhibited good sensitivity at 299 °C temperature to low concentrations (100 ppb) of Benzene which can be potentially used as a resistive gas sensor.... 

Porous poly-silicon (PPS) is a cheaper alternative to single crystal porous silicon and is a favorable choice for making gas sensors. In this study, porous poly-silicon samples were prepared using different HF concentrations and the structural and gas-sensing properties were studied. The topography of the surface was investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The variation of electrical conductivity of the samples in the presence of dry air-diluted acetone, ethanol and methanol showed that for a constant etching current, the sensitivity was highest for samples prepared in 13% HF solution. The structure of the films in the optimum HF... 

We prepared porous silicon samples coated by continuous palladium layer in electroless process. Scanning electron microscopy (SEM) showed cauliflower-shape Pd clusters on the surface. I–V curves of Schottky like Pd/porous Si samples were measured in air and in hydrogen. These measurements showed a metal–interface–semiconductor configuration rather than an ideal Schottky diode. Variations of the electrical current in the presence of diluted hydrogen at room temperature revealed that the samples can sense hydrogen in a wide range of concentration (100–40,000 ppm) without any saturation behavior. Hydrogen sensing properties of these samples were investigated at room temperature for a duration... 

Pd–WO3 nanostructures were incorporated on graphene oxide (GO) and partially reduced graphene oxide (PRGO) sheets using a controlled hydrothermal process to fabricate effective hydrogen gas sensors. Pd–WO3 nanostructures showed ribbon-like morphologies and Pd–WO3/GO presented an irregular nanostructured form, while Pd–WO3/PRGO exhibited a hierarchical nanostructure with a high surface area. Gas sensing properties of thin films of these materials were studied for different hydrogen concentrations (from 20 to 10,000 ppm) at various temperatures (from room temperature to 250 °C). Although adding GO in the Pd–WO3, after hydrothermal process could increase the film conductivity, gas sensitivity... 

Reduced graphene oxide (RGO) was used to improve the hydrogen sensing properties of Pd and Pt-decorated TiO2 nanoparticles by facile production routes. The TiO2 nanoparticles were synthesized by sol–gel method and coupled on GO sheets via a photoreduction process. The Pd or Pt nanoparticles were decorated on the TiO2/RGO hybrid structures by chemical reduction. X-ray photoelectron spectroscopy demonstrated that GO reduction is done by the TiO2 nanoparticles and Ti–C bonds are formed between the TiO2 and the RGO sheets as well. Gas sensing was studied with different concentrations of hydrogen ranging from 100 to 10,000 ppm at various temperatures. High sensitivity (92%) and fast response time... 

Development of a new micro gas sensor is essential for the analysis of the outcome of gas separation devices. In this paper, direct simulation Monte Carlo (DSMC) modeling of low-pressure gas sensor was performed to investigate the effect of physical parameters on the performance and main characteristics of this type of actuator in various operating conditions. Extensive parametric studies were done and the effect of ambient pressure, temperature and gap of arms were comprehensively investigated. Our findings showed that gap size significantly influences the flow features and force generation inside the sensor. © 2018 Bulgarian Academy of Sciences, Union of Chemists in Bulgaria  

We prepared porous silicon samples coated by continuous palladium layer in electroless process. Scanning electron microscopy (SEM) showed cauliflower-shape Pd clusters on the surface. I-V curves of Schottky like Pd/porous Si samples were measured in air and in hydrogen. These measurements showed a metal-interface-semiconductor configuration rather than an ideal Schottky diode. Variations of the electrical current in the presence of diluted hydrogen at room temperature revealed that the samples can sense hydrogen in a wide range of concentration (100-40,000 ppm) without any saturation behavior. Hydrogen sensing properties of these samples were investigated at room temperature for a duration... 

Direct Simulation Monte Carlo (DSMC) method is applied to evaluate the performance of a new micro gas sensor (MIKRA) for mass analysis of ammonia in the rarefied gas. In order to simulate a rarefied gas inside the micro gas detector, Boltzmann equation is applied to obtain high precision results. This study performed comprehensive studies to reveal the main mechanism of force generation and applied this for the analysis of the gas mixture. Our findings show that value of generated Knudsen force significantly varies when the percentage of the NH3 varies in the mixture. According to obtained results, the maximum Knudsen force increases when the fraction of the ammonia decreases. Our findings... 

Nanostructured TiO2-Al2O3 films and powders were prepared by a straightforward aqueous particulate sol-gel route. Titanium (IV) isopropoxide and aluminum chloride were used as precursors, and hydroxypropyl cellulose was used as a polymeric fugitive agent in order to increase the porosity. The effect of Al:Ti molar ratio was studied on the crystallization behavior of the products. X-ray diffraction (XRD) revealed that the powders crystallized at 800°C, containing anatase-TiO2, rutile-TiO2 and cubic-Al2O3 phases. Furthermore, it was found that Al2O3 retarded the anatase to rutile transformation. Transmission electron microscope (TEM) image showed that one of the smallest crystallite sizes was...