Sharif Digital Repository

Utilizing improved production methods have been always challenging in upstream industries. Nowadays, hydraulic fracturing is one of the most prestigious mechanical methods. Application of this method is in wells with low productivity index. Hydraulic fracturing efficiency depends on various factors, such as fracture geometry, fluid composition, and stress distribution. But some of them would be ignored, such as fracture geometry, which is neglected due to nongravity and lack of investigation of DFN statistical population assumption. The authors develop a more comprehensive methodology based on fracture geometry and aim to model one of the gas reservoirs in Iran that is naturally fractured by... 

hydraulic fracturing is one of the most prestigious mechanical methods which used as a facile production rate improvement method. Application of this method is in wells with low productivity index. Hydraulic fracturing efficiency depends on various factors, like fracture geometry, fluid composition and stress distribution. But some of them would be ignored. Such as fracture geometry which is neglected due to non-gravity and lack of investigation of DFN statistical population assumption. In this paper we develop a more comprehensive methodology based on fracture geometry, we aim to model one of the gas reservoirs which is naturally fractured, by using well-known commercial software. Based on... 

A composite coating containing silver, fluoride and hydroxyapatite (Ag-FHA) was developed on titanium substrate by sol-gel method. Triethylphosphite, hydrated calcium nitrate, ammonium fluoride and silver nitrate were used respectively, as P, Ca, F and Ag precursors with a Ca:P ratio 1.67 and concentration of silver was 0.3 wt%. Coatings were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and atomic absorption spectrometry (AAS). Potentiodynamic polarization measurements in simulated body fluid proved corrosion protection caused by both Ag-FHA coatings. Antibacterial activity of coatings against... 

The biodegradation behavior of Mg, coated by polymethyl methacrylate as well as polymethyl methacrylate (PMMA)−bioactive glass (BG) composite was investigated. Electrophoretic deposition and dip coating techniques were adopted to prepare composite coating using a suspension of different percentages of the above two chemical materials. The deposited coatings were characterized using SEM, EDS, FTIR, and water contact angle measurements. Biodegradation behavior study of the coated Mg was performed using linear polarization, impedance spectroscopy, and immersion tests in simulated body fluid. The compact and homogeneous composite coating was developed as evidenced by electron microscopy results.... 

Asphaltene deposition is a problematic challenge for oil production. Changes in key parameters like pressure and fluid composition during natural depletion and different gas injection scenarios may result in asphaltene precipitation and deposition. In this work, a model is developed by application of mass balance equations, momentum equation, asphaltene deposition and permeability reduction models. An algorithm is developed to perform iterative procedure to solve the numerical equations that contains highly coupled variables. Indeed, an equation is introduced to calculate the saturation of the precipitated asphaltene phase. Model parameters were determined by genetic algorithm which is a... 

In this research, surface modification of aromatic polyamide thin film composite (TFC) reverse osmosis (RO) membranes was carried out using dielectric barrier discharge (DBD) plasma treatment to improve the performance and fouling resistance of prepared RO membranes. First, polyamide TFC RO membranes were synthesized via interfacial polymerization of m-phenylenediamine and trimesoyl chloride monomers over microporous polysulfone support membrane. Next, the DBD plasma treatment with 15 s, 30 s, 60 s, and 90 s duration was used for surface modification. The surface properties of RO membranes were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR),... 

In this research, surface modification of aromatic polyamide thin film composite (TFC) reverse osmosis (RO) membranes was carried out using dielectric barrier discharge (DBD) plasma treatment to improve the performance and fouling resistance of prepared RO membranes. First, polyamide TFC RO membranes were synthesized via interfacial polymerization of m-phenylenediamine and trimesoyl chloride monomers over microporous polysulfone support membrane. Next, the DBD plasma treatment with 15 s, 30 s, 60 s, and 90 s duration was used for surface modification. The surface properties of RO membranes were characterized by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR),... 

Thermoplastic starch (TPS), as a natural based polymer, is known to have the capability to be used in biological applications due to its biocompatibility and biodegradability. In this study, mechanical properties of TPS are enhanced by incorporating bioactive β-tricalcium phosphate (β-TCP) particles for bone tissue engineering applications. Starch-based nanocomposites containing 3, 5, and 10 wt% of β-TCP nanoparticles (TT3, TT5, TT10) were made using a co-rotating twin-screw extruder. Dynamic light scattering (DLS) and X-ray diffraction (XRD) techniques were employed to analyze the nanocomposites. Moreover, degradability, swelling degree, and biomineralization in a simulated body fluid (SBF)...