Sharif Digital Repository

On-chip phase separation of multiphase microflows at the divergence point of Y-shaped microfluidic junctions is an effective way for integrating continuous microstructured devices. In this study, flow pattern maps of various solvent pairs based on the volumetric flow rates of both phases have been drawn experimentally and compared with numerical prediction to investigate the effective domain for which complete phase separation occurred. Furthermore, sufficient separation of aqueous and organic phases at the end of the microchannel was achieved by controlling the pressure difference at the liquid-liquid interface via loading back-pressure on the organic phase. A mathematical model based on... 

Numerical simulations of the turbulent flow around single and side-by-side piles at different spacing ratios (centre-to-centre distance to the pile diameter) with flow Reynolds number of 105 on the fixed flat-bed are presented. The calculations are performed using the computational fluid dynamics model, FLOW-3D, which solves the Navier–Stokes equations in three dimensions with a finite-volume method. The numerical results of time-averaged flow patterns around single and side-by-side piles are validated using the available experimental measurements. At the downstream of the single pile, dimensionless vortex shedding frequency (Strouhal number) is estimated as 0.22. The maximum values of bed... 

Multiphase flow is fundamental to different fields of engineering and science including petroleum engineering. In oil and gas, flow of multiple phases inside wells is a common phenomenon. In such conditions, petroleum engineers deal with different design and operational difficulties due to complexities involved in flow of multiple phases inside a well. Unlike flow of gas and liquid inside a well, the liquid-liquid flow inside a horizontal well has received rather less attention. This study is aimed at experimentally investigating multiphase flow in a horizontal well by using a 12 m length and 30 mm diameter well made of Plexiglas. Despite the importance of defining pattern transition... 

Patterns formed by the flow of an inhomogeneous fluid (suspension) over a smooth inclined surface were studied. It was observed that fractal patterns form. There exists a threshold angle for the inclination above which global fractal patterns are formed. This angle depends on the particle size of the suspension. We observed that there are two fractal dimensions for these patterns, depending on the area from which the pattern is extracted. If the pattern is taken from the top which only consists of the beginning steps of the pattern forming, one finds two fractal dimensions, i.e. 1.35-1.45 and 1.6-1.7, in which the first one is dominant while, if the entire pattern is taken, then a fractal... 

Pulsating heat pipe (PHP) is a type of wickless heat pipe that has a simple structure and an outstanding thermal performance. Nanofluid is a type of fluid in which nanoparticles are dispersed in a base fluid and have generally a better thermal conductivity in comparison with its base fluid. In this article, the performance of a nanofluid PHP is investigated. Graphene/water nanofluid with a concentration of 1 mg mL−1 and TiO2 (titania)/water nanofluid with a concentration of 10 mg mL−1 are used as the working fluids. To simultaneously investigate the thermal performance and flow regimes in the PHP, a one-turn copper PHP with a Pyrex glass attached to its adiabatic section is used. A one-turn... 

Pulsating heat pipe (PHP) is a type of wickless heat pipe that has a simple structure and an outstanding thermal performance. Nanofluid is a type of fluid in which nanoparticles are dispersed in a base fluid and have generally a better thermal conductivity in comparison with its base fluid. In this article, the performance of a nanofluid PHP is investigated. Graphene/water nanofluid with a concentration of 1 mg mL −1 and TiO 2 (titania)/water nanofluid with a concentration of 10 mg mL −1 are used as the working fluids. To simultaneously investigate the thermal performance and flow regimes in the PHP, a one-turn copper PHP with a Pyrex glass attached to its adiabatic section is used. A... 

The equilibrium signal-setting problem is stated and subsequently formulated as a continuous equilibrium network design problem. The bilevel formulation is nonconvex and therefore cannot be solved for global optima by using descent solution algorithms. Therefore, a lower bound using a system optimal flow pattern is proposed that will be quite tight in both uncongested and highly congested network traffic situations. A solution algorithm based on the standard steepest-descent method is proposed for the lower-bound problem. Performance of the solution algorithm on a network problem is reported  

This Paper presents simulation of Electroosmotic phenomenon in a capillary using an extended hybrid finite-volume-element method. Most of the last electroosmotic phenomenon studies in microchannels do not take into consideration the effect of reservoirs and pressure drops occurred at the inlet and outlet of the microchannel. This neglect may lead to a few drawbacks. For example, the incorrect pressure drops can significantly alter the flow patterns and mass flow rates in microchannels. As a remedy the use of reservoirs at the two ends of a microchannel has been recently practiced as a novel strategy to overcome this drawback. However, this remedy needs careful attention because the resulting... 

In this paper, a three-invariant cap model is developed for the isotropic-kinematic hardening and associated plasticity of granular materials. The model is based on the concepts of elasticity and plasticity theories together with an associated flow rule and a work hardening law for plastic deformations of granulars. The hardening rule is defined by its decomposition into the isotropic and kinematic material functions. The constitutive elasto-plastic matrix and its components are derived by using the definition of yield surface, material functions and non-linear elastic behavior, as function of hardening parameters. The model assessment and procedure for determination of material parameters... 

Purpose - One major challenge in turbulent flow applications is to control the recirculation zone behind the backward-facing step (BFS). One simple idea to do so is to modify the original BFS geometry, of course, without causing adverse or undesirable impacts on the original characteristics of the primary stream. The main objective of this work is to examine the solidity of the recirculation zone behind several different geometries which are slightly to moderately different from the original BFS geometry. Design/methodology/approach - The implemented modifications cause complicated irregularities at the boundaries of the domain. The experience shows that the mesh distribution around these... 

In this paper a three-dimensional numerical model is developed in order to study the heat transfer enhancement in rectangular microchannels due to electrokinetic effect. The electrokinetic body force on fluid elements gives some superior convective transport properties to the flow relative to pure pressure driven flow in microchannels. Unlike the conventional parabolic velocity profile of pressure driven laminar flow, the electrokinetic body force transforms the velocity profile to a slug-like flow. Due to sharp velocity gradient near the wall, the convective heat transfer properties of the flow are improved dramatically. Net charge distribution across the channel is obtained by solving the... 

Finding the optimal flow pattern in bipolar plates of a proton exchange membrane is a crucial step for enhancing the performance of the device. This design plays a critical role in fluid mass transport through microporous layers, charge transfer through conductive media, management of the liquid water produced in microchannels, and microporous layers and heat management in fuel cells. This article investigates different types of common flow patterns in bipolar plates while considering a uniform pressure and velocity distribution as well as a uniform distribution of reactants through all the surfaces of the catalyst layer as the design criteria so that there would be a consistent electron... 

Two-phase flow inside the oil and gas wells and flow path lines is a usual occurrence in petroleum and petrochemical studies. Due to its complexity, flow transfer parameters such as hold up and pressure drop and their dependency on the flow regime maps are not well understood yet. This study is aimed at analyzing holdup for oil- water system and evaluation of this parameter by means of Image processing under different available flow regime conditions. In addition, different oil-polymer systems have been studied to evaluate the impact of polymer concentration on transport criteria. The experimental setup used for this study is consisted of a 12 m long Plexiglas pipe with an inner diameter of... 

Two-phase flow inside the oil and gas wells and flow path lines is a usual occurrence in petroleum and petrochemical studies. Due to its complexity, flow transfer parameters such as hold up and pressure drop and their dependency on the flow regime maps are not well understood yet. This study is aimed at analyzing holdup for oil- water system and evaluation of this parameter by means of Image processing under different available flow regime conditions. In addition, different oil-polymer systems have been studied to evaluate the impact of polymer concentration on transport criteria. The experimental setup used for this study is consisted of a 12 m long Plexiglas pipe with an inner diameter of...