Sharif Digital Repository

In this research TiO2 hollow spheres with different diameters were prepared using titanium tetraisopropoxide (TTIP) as the TiO2 precursor. Carbon spheres with average sizes of 230, 325 and 450 nm were prepared as the templates by hydrothermal method. Then TiO2 was deposited on the surface of the carbon spheres through a liquid phase deposition (LPD) process. This two dimensional growth was performed in an appropriate concentration of TTIP and different LPD times. Finally the TiO2 hollow spheres were achieved for specific LPD times by burning the carbon templates. Two kinds of TiO2 nanocrystals with sizes around 20 nm were hydrothermally grown in acidic (pH = 1.5) and basic (pH = 10)... 

The gas nanosensor of indium oxide nanowires in laser assisted approach, doped with tin and zinc for gas sensing and 1D growth purposes respectively, was reported. The nanowires were very sensitive to H2S gas in low concentration of 20 ppb gas at room temperature. The fast dynamic intensive and sensitive response to gas was in a few seconds with an on/off sensitivity ratio of around 10. The square cross-section indium oxide nanowires were fabricated through physical vapor deposition (PVD) mechanism and annealing approach. The field emission scanning electron microscopy (FESEM) observations indicated that the annealing temperature was vital in nanostructures' morphology. The fabricated... 

In this paper, the stable and reproducible tellurium doped ZnO nanowires (Te-ZnO NWs) photodetector with intensive responsively is presented. The Te-ZnO NWs were fabricated by physical vapor deposition (PVD) growth mechanism. Field emission scanning electron microscope (FESEM) images showed that the fabricated nanowires were 50 nm in diameter and several microns in length. The high resolution transmission electron microscopy indicated that the synthesized nanowires were crystalline and their phase characterization was validated by the X-ray diffraction (XRD). The photoluminescence (PL) studies of these nanowires showed a strong photoluminescence (PL) emission peak in the green region. It was... 

In this research, a finite element model was developed in order to simulate the two-step residual stress distribution of a thermal barrier coating system, considered to be used in diesel engine cylinder head, with a real roughness and real porosity. Two steps including the bond coat and the top coat deposition processes were taken into account. The real geometry of coating layers, including the roughness and the porosity, was also considered based on a scanning electron microscopy image. Then, effects of the convective heat transfer coefficient and initial substrate and substrate/bond coat preheating temperatures on the residual stress were studied. Obtained results illustrate that the... 

Changes in thermodynamic properties such as pressure, temperature, and composition may result in asphaltene precipitation and deposition in porous media. In addition, asphaltene deposition can cause wettability alteration, permeability reduction, and ultimately a decrease in the productivity of a reservoir. Natural depletion is one of the most common processes of asphaltene deposition in which pressure changes destabilize the dissolved asphaltene in the oil and settle them onto the rock surface. In this work, natural depletion experiments in consolidated core samples were performed under simulated reservoir conditions to obtain reliable data and analyze the asphaltene deposition mechanisms.... 

Different models have been proposed for deposition of asphaltene on reservoir rocks that due to complexity of asphaltene nature, most of them have not been productive. Here, a reliable model is proposed which despite of previous models, considers the change in asphaltene saturation in the core. The obtained experimental data in the laboratory was used for model validation. In this work, a series of core flooding tests was carried out in presence of connate water at different solvent-oil volume ratios. Pressure drop was measured at three different terminals along the core. The obtained experimental data as well as mass balance equations, momentum equation, asphaltene deposition and... 

On silicon substrates, boron nitride nanosheets (BNNS) consisting of interconnected hexagonal boron nitride nano-layers were produced via chemical vapor deposition process at 1200 °C whose roughness's are at the micrometer- and nanometer-scale. The BNNS were functionalized in argon plasma admixed with ammonia or nitrogen or oxygen. The samples were characterized to investigate the surface chemistry and structural changes after plasma treatment using X-ray photoelectron spectroscope and Micro-Raman spectroscope techniques, respectively. While no significant changes in the surface features, upon plasma treatments of the BNNS, were noticed during SEM and TEM examination, the oxygen functional... 

Asphaltene deposition is one of the unresolved problems in oil industries. Little information is available on the critical question of "how fast" the flocculated asphaltene particles deposit across the production wells from the flowing oil. In this study, the mechanisms of deposition of flocculated asphaltene particles from oil have been studied experimentally and theoretically under forced convective conditions using an accurate thermal approach. The effects of oil velocity, flocculated asphaltene concentration and temperature on the rate of asphaltene deposition are investigated. It is observed that during the first few weeks the deposition mechanism is dominant and the erosion of the... 

Electrochemical deposition of aluminum and lead from basic molten AlCl3-NaCl-KCl mixture on an aluminum electrode at 180 °C was studied by the methods of voltammetry, potential and current transient and constant current deposition. The deposition of aluminum was found to proceed via a nucleation/growth mechanism, while the deposition of lead was found to be diffusion controlled. The diffusion coefficient calculated for Pb2+ ions in basic melt by voltammetry was in agreement with the deductions of transient method. The analysis of the chronoamperograms indicates that the deposition process of lead on Al substrates was controlled by 3D diffusion control, nucleation and growth. The processes... 

A modeling approach is presented for the first time to model the dependence of short-circuit current density (J sc ) and open-circuit voltage (V oc ) on the grain size g in three thin film solar cells including the emerging perovskites. The variation of J sc and V oc with the grain size (g) of three different solar cells with CdTe, CZTS and perovskite absorber layers are modelled and fitted with the experimental dataset collected from relevant literature. The experimental literature suggested that the grain size of absorber layers in solar cells is controlled during the deposition process by adjusting the growth rate, temperature and ambient. The model has been successfully applied to the... 

In terms of manufacturability, there is a high tendency to deposit light-absorbing CuInS2 films by solution processing methods like ink-based depositions. In particular, for nanoparticle inks, the synthesis of highly dispersed and stable inks, with uniformity in the deposition process, is a serious challenge. Here, we demonstrate a novel two-step low-temperature CuInS2 film deposition method in which the In2S3 is deposited first. It then partially is converted into CuInS2 through the infiltration of Cu+ ions in the In2S3 layer in a dip-coating process. The resulting films are highly uniform, with diffraction peaks indicating the formation of pure CuInS2 phase. The proper stoichiometry of... 

The main drawback of lithium-sulfur (Li-S) batteries which leads to a short lifetime, is the shuttle effect during the battery operation. One of the solutions to mitigate the shuttle effect is the utilization of interlayers. Herein, graphene oxide (GO) paper as an interlayer has been implemented between the sulfur cathode fabricated by the vapor deposition process as a binder-free electrode and a separator in a Li-S battery in order to gain a sufficient capacity. The morphological characteristics and electrochemical performance of the fabricated electrode have been investigated. The fabricated battery demonstrates an initial discharge capacity of 1265.46 mAh g-1 at the current density of 100... 

A new ternary nanocomposite based on graphene oxide (GO), polypyrrole (PPy) and vanadium pentoxide (V2O5) is obtained via one-step electrochemical deposition process. Electrochemical deposition of V2O5, PPy and GO on a stainless steel (SS) substrate is conducted from an aqueous solution containing vanadyl acetate, pyrrole and GO to get V2O5/PPy/GO nanocomposite. Characterization of the electrode material is carried out by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and atomic force microscopy (AFM). The electrochemical performance of the as-prepared nanocomposite is evaluated by... 

TiO2 nanorods have been successfully grown into a track-etched polycarbonate (PC) membrane by a particulate sol-electrophoretic deposition from an aqueous medium. The prepared sols had a narrow particle size distribution around 17 nm and excellent stability against aging, with zeta potentials in the range of 47-50 mV at pH 2. It was found that TiO2 nanorods were grown from dilute aqueous sol with a low, 0.1-M concentration. Fourier transform infrared spectroscopy (FT-IR) analysis confirmed that a full conversion of titanium isopropoxide was obtained by hydrolysis, resulting in the formation of TiO2 particles. X-ray diffraction (XRD) results revealed that TiO2 nanorods dried at 100 °C were a...