Sharif Digital Repository

Zinc–silicanano-composite coatings were produced by successive dip coatand sintering procedure from different sol-gel solutions. The surface and cross-sectional morphologies of Zn-SiO2 nano-particles (NPs) were examined using field emission scanning electron microscopy (FE-SEM). Corrosion resistance evaluated by means of polarization and electrochemical impedance spectroscopy showed that even thin films of Zn-SiO2 in orders of 200 nm can have corrosion rates as low as conventional hot dip galvanized steels. Multi-layers coatings have been studied and showed that 10 layers coating with the thickness of 2m has the lowest corrosion rate with the passive region in anodic branch. Corrosion... 

In this study anodized none composite and composite film containing ZrO2 nanoparticles were prepared on 1050 Al Alloy using hard anodizing method in sulfuric and oxalic acid mixed solution by pulse Currents. The microstructure and properties of the film were studied by field emission scanning electron microscopy with EDS analyzer and XRD diffraction and friction wear test were performed to evaluate the mechanical properties of coating . Results indicate that the composite film with ZrO2 nanoparticles have reduced friction coefficient with high micro hardness friction coefficient of composite film can be small as 0.16 which is much smaller than that 0.39 of none composite film. Micro hardness... 

Main aim of this work was to obtain the harder zinc coating and increasing the anti corrosive properties by mean of adding SiO2 particles by electrophoretic method.
The coating was applied on the substrate surface by mean of electro co-deposition technique in three different electrolytes ethanol, methanol and water. The morphology of the coating in each electrolyte studied by scanning electron microscope (SEM).For the Zn/SiO2 coatings achieved in ethanol solvent the polarization and EIS tests was took place and found that for the Zn/SiO2 coating contain less than 10% SiO2 the corrosion rate decreased but for the coatings contains more than 10% SiO2 the paradox occurred because of the... 

Ni-SiC nanocomposite coatings are considered as corrosion resistant coatings with better tribological properties. In order to get superior properties, the amount of added particles should be increased. But high concentration of particles has some drawbacks such as low adhesion to substrate, probability of cracking in coating due to heat expansion coefficient difference between substrate and coating and also embrittlement of coating and low elasticity. In this study, the possibility of producing Ni-SiC nanocomposite coatings with FGM structure was investigated. SiC particles concentration was 5 to 80 g/l and the current density was between 3 to 5 A/dm¬2. The pH of bath and temperature was... 

Electroplating is an appropriate method for co-deposition of metallic, non-metallic and polymeric fine particles onto a metal matrix for production of functional coatings. In this study, chromium and Cr–Al2O3 composite coatings are electrodeposited from trivalent chromium bath by using DC and square pulse current. Dependence of the amount of Al2O3 nano-particles trapped into the coatings on the Al2O3 bath concentration, average current density, particle size, agitation rate and type of the current is investigated. These parameters are optimized for the highest co-deposition amount of the Al2O3 onto chromium layer. Optimum values are 20g/l Al2O3, 200 rpm stirring rate and 25A/dm2 current... 

The aim of this project is investigation on synthesis and characterization of the TiO2-CNT nanocomposite films on aluminum substrate by sol-gel dip coating method. The pure TiO2 and TiO2-CNT nanocomposite layers were coated on aluminum substrate and heat treated in 400 C. In this work Ti-tetra isopropxide and different amounts of CNTs (5,10,15 %wt), were used for obtain the composites. The coatings were characterized by X-Ray diffraction (XRD) and the crystallite size of TiO2 was calculated by Scherrer formula. The corrosion properties of coating were examined by polarization test, and corrosion resistance of pure TiO2 was compared with TiO2-CNT coatings, and It showed that the composite... 

Composite coatings including self-lubricant particles such as graphite, MoS2, Al2O3 and SiC are extensively used to decrease the coefficient of friction of tribo-surfaces. Adding lubricant particles to an appropriate metallic matrix like copper, nickel, lead and their alloys is a suitable option in severe condition –for instance high temperature and low pressure- which liquid lubricants will be failed. Bronze can give various properties such as wear resistance, corrosion and oxidation protection, However cyanide solutions for electroplating process have environmentally limited for plating of Cu-Sn. In this research, a chloride electrolyte for bronze electroplating was developed and effect of... 

At the first stage, chitosan-hydroxyapatite-multiwalled carbon nanotube (CH-HA-MWCNT) composite coatings were synthesized by electrophoretic deposition technique (EPD) on Ti6Al4V and 316L stainless steel substrates at different levels of pH and characterized by X-ray diffraction (XRD), Raman spectroscopy, FTIR and field emission scanning electron microscopy (FESEM). A smooth distribution of HA and MWCNT particles in a chitosan matrix with strong interfacial bonding was obtained. At the second stage, effect of pH and MWCNT content of the suspension on corrosion behavior and mechanism of deposition were studied. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS)... 

Metallic implants are useful in dental and orthopedic applications. Bio coating is necessary to improve bio-compatibility and bio-activation of metallic implants. For this goal, HA is the most important material. In this research, the goal is to improve bio-compatibility of St. St 316 by coating HA, HA-ZrO2, HA-TiO2, HA-ZrO2-TiO2 using combination of electrodeposition and electrophoretic methods. To form HA, calcium and phosphor salt solution was used then ZrO2- TiO2 nanoparticles was added to solution. In order to analyst the coatings different tests were done. Thickness analysis, XRD, FT-IR, FE-SEM and EDS, bonding Strength, Polarization test, bio-compatibility and surface roughness... 

Ni-Co/SiC composite coatings with various contents of SiC nano particles were electrodeposited in a modified watt type of Ni-Co bath containing 20 nm SiC nano particles to be codeposited. The influences of the SiC concentration, current density, stirring rate of the deposition bath on the composition of the coatings were investigated and these parameters optimized for highest amount of SiC codeposition. The optimized deposition parameters were 40 g/l SiC and 480 rpm stirring rate and current density equal to 4 A/dm2. Ni-Co/SiC composite coating was deposited with the maximum particles content of 30.5 volume percent. Linear voltammetry demonstrates addition of the SiC to the Ni-Co deposition...