Sharif Digital Repository

In this study organically modified nanoclay were prepared by exchanging of the cetyltrimethylammonium (CTAB), with inorganic/metal ions/cations in montmorillonite structure. To investigate the influence of the amount of modifier on basal spacing and subsequent removal efficiency of hydrocarbon, different amount of modifier was used. The modified and unmodified nanoclays characterized by XRD, CHN and FTIR techniques. The X-ray diffraction results showed that the interlayer spacing of CTAB-modified clays increased from 12 to 22Å. The effectiveness of the sorbent materials for sorption of a range of products was investigated using crude oil, kerosene, gasoline and toluene. The process... 

In this study, effects of glycerol (10, 20, and 30 wt%) and Sodium Montmorillonite (Na-MMT) (0%, 2.5%, and 5%) contents on the degradation of corn starch polymers were investigated. Films were prepared by casting corn starch solution using a modified method to enhance the nanoclay distribution. Biodegradability studies were performed by enzymatic and burial tests using pristine and enriched soils. The biodegradability of samples in pristine soil was faster, and all samples were fully degraded in 6 months. The effect of nanoparticles on the mass reduction in degradation was more pronounced than that of glycerol. In all glycerol concentrations, Na-MMT addition increased tensile strength. FTIR... 

The properties of self-compacting concrete (SCC) can be manipulated by the addition of nano-montmorillonite (NMMT) clays. This paper presents the results of an experimental investigation on incorporating small dosages of NMMT clays (.25, .50, .75 and 1.00% addition by mass of total cementitious material) into SCC. Tests were conducted on fresh and hardened specimens to measure workability (by slump flow, V-funnel and L-box), mechanical (by compressive and splitting tensile strengths), durability (electrical resistivity and water penetration) and microstructural (X-ray diffraction and scanning electron microscopy) properties of control and NMMT-reinforced SCCs. The results showed that the... 

Inclusion of nano-clays into hydrogels is an efficient approach to produce nanocomposite hydrogels. The introduction of nano-clay into hydrogels causes an increase in water absorbency. In the present work, Nanocomposite hydro-gels based on kappa-carrageenan were synthesized using sodium montmorillonite as nano-clay. Acrylamide and meth-ylenebisacrylamide were used as monomer and crosslinker, respectively. The structure of nanocomposite hydrogels was investigated by XRD and SEM techniques. Swelling behavior of nanocomposite hydrogels was studied by varying clay and carrageenan contents as well as methylenebisacrylamide concentration. An optimum swelling capacity was achieved at 12% of sodium... 

In this article, preparation of polypropylene/clay nanocomposites (PPCNC) via in situ polymerization is investigated. MgCl2/montmorillonite bisupported Ziegler-Natta catalyst was used to prepare PPCNC samples. Montmorillonite (MMT) was used as an inert support and reinforcement agent. The nanostructure of the composites was characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy techniques. Obtained results showed that silica layers of the MMT in these PPCNC were intercalated, partially exfoliated, and uniformly dispersed in the polypropylene matrix. Thermogravimetric analysis showed good thermal stability for the prepared PPCNC. Differential... 

We carry out a series of cross-correlation analysis of raw well-log data, in order to study the possible connection between natural gamma ray (GR) logs and other types of well logs, such as neutron porosity (NPHI), sonic transient time (denoted usually by DT), and bulk density (RHOB) of oil and gas reservoirs. Three distinct, but complementary, methods are used to analyze the cross correlations, namely, the multifractal detrended cross-correlation analysis (MF-DXA), the so-called Qcc(m) test in conjunction with the statistical test-the χ2(m) distribution-and the cross-wavelet transform (XWT) and wavelet coherency. The Qcc(m) test and MF-DXA are used to identify and quantify the strength of... 

Copolypropylene/organoclay nanocomposites are prepared by melt intercalation method in this research. Two different routes for addition of compatibilizer are examined, i.e. addition in the twin-screw extruder along with the polymer and the clay powder simultaneously and premixing the compatibilizer with the reinforcement in a batch mixer before addition to the polypropylene (PP) matrix. Morphology, tensile and impact properties and deformation mechanisms of the samples made via two procedures are studied and compared with those of the noncompatibilized system. To study the structure of nanocomposites, x-ray diffraction and transmission electron microscopy techniques are utilized. The... 

Novel polyampholytic superabsorbing nanocomposites based on the zwitterionic sulfobetaine monomer [3-(methacrylamido)propyl)]dimethyl(3- sulfopropyl)ammonium hydroxide were synthesized through in situ polymerization in aqueous solution with different contents of an organo-modified clay (OMMT, Cloisite 30B). Structural and thermomechanical properties of hydrogels were characterized by FT-IR, XRD, and DMTA, respectively. Swollen gel strength of hydrogels was determined by a rheological method. Storage modulus of the hydrogels was considerably improved in comparison with its the clay-free counterpart. The nanocomposite hydrogel containing 15% OMMT possessed the highest gel strength. The glass... 

The properties of self-compacting concrete (SCC) can be manipulated by the addition of nano-montmorillonite (NMMT) clays. This paper presents the results of an experimental investigation on incorporating small dosages of NMMT clays (.25,.50,.75 and 1.00% addition by mass of total cementitious material) into SCC. Tests were conducted on fresh and hardened specimens to measure workability (by slump flow, V-funnel and L-box), mechanical (by compressive and splitting tensile strengths), durability (electrical resistivity and water penetration) and microstructural (X-ray diffraction and scanning electron microscopy) properties of control and NMMT-reinforced SCCs. The results showed that the... 

Nanocomposites of poly(ethylene terephthalate) and two different montmorillonite-based organoclays were prepared by a co-rotating twin screw extruder. Dispersion of nanoclays in the polymer matrix was examined by TEM and XRD. Nanocomposites with lower content of organoclay showed exfoliated morphology while by increasing the amount of organoclay the intercalated morphology was more prevalent. Both organoclays had a good intercalation with PET and were uniformly dispersed within the polymer. Oxygen permeability of thin films of nanocomposites showed that the nanocompo-sites had better oxygen barrier properties than the neat PET. Tensile and impact properties of the nanocomposites also were... 

In this investigation, core-shell rubber particles and organically modified clay were added to an epoxy resin and the changes in mechanical behavior were studied. As expected, the yield strength of the organoclay-filled epoxies increased modestly with increasing clay content and the yield strength of the rubber-modified compounds decreased with rubber content. Interestingly, the compressive yield strength of epoxy resins containing both rubber particles and organoclay (a.k.a. hybrid nanocomposites) was found to be independent on organoclay content (up to 5 phr). The fracture toughness of organoclay-filled epoxies increased modestly with clay content and, as expected, the increases in... 

Novel montmorillonite (Mt) chitosan/poly(vinyl alcohol) (PVA) nanocomposite electrospun nanofibrous membranes (ENM) were prepared and utilized for the treatment of colored wastewater. The Mt. with different mass percentages (0, 1.0, 2.0 and 3.0 mass%) was added to the membrane structure, and its effect on morphology, pore size, porosity, mechanical strength, and permeation properties of ENM were investigated. The fabricated membranes were used as affinity membranes for dye removal with ultrafast permeating adsorption. The results showed that incorporating Mt. as a reinforcing agent improved the nanocomposite ENM resistance to compaction. Young's modulus for the prepared membranes increased... 

In the last three decades, nanoclay fillers have been increasingly used to improve the mechanical, thermal, barrier and biological properties of the polymers. Nevertheless, incorporation of clays into the hydrophobic polymer matrices leads to the formation of the microcomposites with the minimal improvement in properties. To overcome the intrinsic incompatibility between the clays and the hydrophobic polymers, clay particles are organophilized using organic modifiers. The organic modifier should be thermodynamically miscible with the polymer. In the case of the composites prepared at high temperatures, the organic modifier should also have a high thermal stability to withstand the processing... 

In this paper, preparation of polyethylene/clay nanocomposites (PECNC) by in situ Ziegler-Natta catalyst polymerization was investigated. A Ziegler-Natta catalyst was first supported on montmorillonite (MMT) type clay and subsequently used for polymerizing ethylene. Clay and clay supported catalyst were characterized by Fourier transmission infrared and ICP method. X-ray diffraction (XRD) and transmission electron microscopy results show that silicate layers of the mineral clay in prepared nanocomposites were intercalated and exfoliated in the polymeric matrix. Differential scanning calorimetry results show that the prepared nanocomposites have higher crystallization temperature than pure... 

This study intends to replace polyethylene multi-layer films used in food packaging industry with single-layer polyethylene nanocomposites films. Nanocomposites of LDPE/LLDPE/ montmorillonite organoclay were prepared by melt compounding in a twin extruder and then film blown to prepare thin films. LLDPE-g-MA was used as compatibilizer to achieve better interaction between the blend and organoclay. Various compositions of organoclay and compatibilizer were prepared. The structure of nanocomposites was characterized by XRD and TEM. Permeability properties were measured using a permeability measuring set-up and aspect ratio of the particles was evaluated using permeability data. The results... 

It is a current practice to employ composite claya mixture of clay and aggregates that float within the clayey matrixas the core of embankment dams that have classically been constructed from pure clays. Experience has shown that significant pore pressures could build up during cyclic undrained loading in composite clays. This may threaten dam stability during earthquake loading. However, it is difficult to attribute a single value to excess pore pressure in conventional seismic stability analysis because of the random nature of earthquake loading, leading to uncertainty in the evaluation of factor of safety against sliding. This article evaluates the importance of pore pressure build-up in... 

A study was conducted to report an observation on the effect of nanoclay fillers on the α-relaxation in an epoxy resin. The observation provided useful facts about glass transition processes in nanoclay-filled epoxy composites. The investigation involved the synthesis of intercalated-exfoliated clay-epoxy compounds, by swelling an organophilic montmorillonite in an aromatic epoxy resin and polymerization. The epoxy resin used in the study was a diglycidyl ether of bisphenol A (DGEBA), EPON 828, with an equivalent weight of 184-190 g/eq from Hexion Specialty Chemicals. The epoxy resin was cured with piperidine, obtained from Sigma-Aldrich. Nanomer® 1.30E. An octadecyl amine treated... 

The morphological, physical and mechanical properties of polypropylene/clay nanocomposites (PPCNs) were prepared by in situ polymerization are investigated. Non-modified scmectite type clay (e.g. bentonite) was used to prepare bi-supported Ziegler-Natta catalyst of TiCl4/Mg(OEt)2/clay. Exfoliated PPCNs were obtained by in situ intercalative polymerization of propylene using produced bi-supported catalyst. X-ray diffraction (XRD) patterns and transmission electron microscopy (TEM) micrograph were used to assess the clay morphology and dispersion of clay. The crystalline structures of PPCNs were characterized by differential scanning calorimetry (DSC). The mechanical properties of PPCNs were... 

In this work, the potential for the auto-ignition of Iranian heavy oil during in situ combustion (ISC) process conditions was studied. Kinetic studies were carried out using thermal analysis techniques. Effects of oxygen partial pressure, reservoir pressure, and clay on the auto-ignition condition were investigated. Based on the experimental results obtained, a kinetic equation was derived for each of the different oil samples in the presence of different sands. The effect of partial pressure of oxygen in the injected air showed that at atmospheric pressure, low temperature combustion (LTC) was initiated at 275°C. Also, enriching the injected air by oxygen lowers the initial LTC temperature... 

Polyethylene/clay nanocomposites (PECNC) were synthesized via in situ Ziegler-Natta catalyst polymerization. Activated catalyst for polymerization of ethylene monomer has been prepared at first by supporting of the cocatalyst on the montmorillonite (MMT) smectite type clay and then active complex for polymerization formed by reaction of TiCl4 and aluminum oxide compound on the clay. Acid wash treatment has been used for increasing hydroxyl group and porosity of the clay and subsequently activity of the catalyst. The nano- structure of composites was investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Obtained results show that silica layers of the mineral clay...