Sharif Digital Repository

A recently developed two-level undercut-profile substrate (2LUPS), containing two levels of plateaus connected by a curved wall with an undercut profile, enables self-forming filaments in a coated conductor during physical line-of-sight deposition of buffer and superconducting layers. In the present study, the 2LUPS concept is applied to a commercial cube-textured Ni-5at.%W tape, and the surface of the 2LUPS coated with two Gd2Zr2O7 buffer layers using chemical solution deposition is examined. Except for narrow regions near the edge of upper plateaus, the plateaus are found to be covered by strongly textured Gd2Zr2O7 buffer layers after dip coating and sintering  

This research investigated the long-term environmental effects on bond strength at the interface between fiber- reinforced polymers (FRPs) and timber. A total of 581 timber specimens were bonded with seven types of FRP sheets (unidirectional and bidirectional glass, carbon, aramid, and hybrids) using a wet lay-up technique. The specimens were exposed to acidic, alkaline, fresh water, and sea water solutions with pH of 2.5, 7, 7.25, 10, and 12.5 for 1, 3, 6, 9, and 12 months. A chamber was also used to simulate ultraviolet radiation after 6 months. A series of single-lap shear tests were then conducted to determine the interfacial bond strength reduction. The results showed that bidirectional... 

Electrospray technique is one of the commonly used methods for generating nanoparticles. In this method, the chemical solution which consists of a polymer and its solvent are injected into an electric field via a nozzle. At the end of this nozzle, due to electric forces, a certain part of this liquid is separated. Then, the separated part is divided into smaller particles and the solvent is evaporated and hence, the nanoparticles are acquired. Produced nanoparticales are collected in deionized water placed under the certain distant from nozzle. However, construction of this method is generally based on practical results. In this paper, modeling and performance evaluation of high voltage... 

The advantages of fiber reinforced polymer (FRP), such as high specific strength, resistance against corrosion and formability, have made it a more acceptable alternative to conventional materials regarding repairing and retrofitting of structures. Although investigations in recent years have proved the concern of civil engineers about the environmental effects on the bond between FRP and concrete or masonry (especially moisture and temperature), only few researches have been reported on FRP-wood interfaces. This research investigated the effect of five different environments on the bond at the interface between FRP and wood. A series of pull-out tests were performed on 375 wood specimens... 

In this study, two different chemical solution methods were used to synthesize Zinc oxide nanostructures via a simple and fast microwave assisted method. Afterwards, the photocatalytic performances of the produced ZnO powders were investigated using methylene blue (MB) photodegradation with UV lamp irradiation. The obtained ZnO nanostructures showed spherical and flower-like morphologies. The average crystallite size of the flower-like and spherical nanostructures were determined to be about 55 nm and 28 nm, respectively. X-ray diffraction (XRD), scanning electronic microscopy (SEM), Brunauer-Emmett-Teller (BET), room temperature photoluminescence (RT-PL) and UV-vis analysis were used for... 

This study examined the bond at the interface of masonry bricks and fiber-reinforced polymer when exposed to five environments. Three fabrics (aramid, carbon, and glass) and one type of epoxy resin were used. A total of 375 brick-fiber-reinforced polymer specimens were made using wet lay-up technic and exposed to chemical solutions at four pH values (2.5, 7, 10, and 12.5) and substitute seawater. The effect of dry heat on the bond at the interface was also investigated. Single-lap shear tests were then carried out on the samples after 2, 4, 6, 8, 10, and 13 weeks of exposure. The experimental results indicated that freshwater and seawater had a considerable effect on the bond strength of... 

Polymer concrete is well-known for quick repairing of concrete structures and pavement. However, there are relatively few studies on the durability of epoxy polymer concrete (EPC). This study aims to investigate the long-term environmental effects on the mechanical properties of EPC. Therefore, EPC and ordinary cement concrete (OCC) specimens were prepared and exposed to four chemical solutions with pH values of 2.5, 7, 12.5 and artificial seawater in intervals of 1, 3, 6, 9 and 12 months. Epoxy resin (10 and 12% by weight) and Portland cement were used as binder phase in EPC and OCC specimens, respectively. Scanning electron microscopy (SEM) was additionally applied to investigate the...