Sharif Digital Repository

In this study, tri-cation phosphate coating of zinc, calcium and iron was applied electrochemically to stainless steel 316 substrates. Cathodic current was used as an accelerator for the phosphating process. The effects of current density on the microstructures of the coatings and the time necessary for the reduction of the oxide layer have been established. For this purpose, analyses such as chronopotentiometery, SEM, EDS and linear polarization were carried out. Results indicated that higher electrophosphating current densities result in finer crystal size of the coating. This effect is detrimental to the quality of the layer. In addition, chemical analyses of the layer revealed that the... 

Electro-deposition process is one of the main steps in the LIGA procedure to fabricate microstructures. In this paper, one-dimensional modeling of Nickel electro-deposition process is implemented on Rayan and developed for simulation of time-dependence diffusion and migration of charge species with reduction reactions on the cathode surface. This model is proposed by considering governing equations on electro-kinetic phenomena consist of Nernst-Plank equation and Poisson's equation of electric potential. Transport of ions toward the cathode is considered based on the effect of convection, reaction rate, diffusion and migration. The numerical results cover two series of data consisting of... 

In this study two cation coating of calcium and zinc has been developed on stainless steel 316L by electrochemical method. Cathodic current used as an accelerator for phosphating process and the effects of current density on microstructure of the phospahted layer and the time needed for termination of the phosphating process has been evaluated by potential-time, SEM, EDS, etc. Results indicate that higher current densities in electrochemical phosphating will result in heavier phospahted layer with finer crystal size which in turn deteriorates the quality of the layer by its higher porosity. Chemical analysis of the layer reveals that using the electrochemical method for phosphating of... 

Gas diffusion layers (GDL) are one of the important parts of the PEM fuel cell as they serve to transport the reactant gases to the catalyst layer. Porosity of this layer has a large effect on the PEM fuel cell performance. The spatial variation in porosity arises due to two effects: (1) compression of the electrode on the solid landing areas and (2) water produced at the cathode side of gas diffusion layers. Both of these factors change the porosity of gas diffusion layers and affect the fuel cell performance. To implement this performance analysis, a mathematical model which considers oxygen and hydrogen mass fraction in gas diffusion layer and the electrical current density in the... 

The effect of pulse reverse current (PRC) method on Ni-Mo coatings electroplated from chloride solution was investigated by various plating parameters such as plating duration, the anodic duty cycle, the anodic current density and the cathodic current density. By increasing the anodic duty cycle and anodic current density, the Mo content of coatings reached 68wt.% and 78wt.%, respectively at cathodic current densities of 500 and 300mAcm-2. The Mo content of coatings increases by the preferential dissolution of Ni on the anodic pulse and also by the replenishment of Mo complexes in the diffusion layer near the substrate surface during the anodic pulse. In comparison with the direct current... 

Nickel-modified glassy carbon electrode (GC/Ni) prepared by galvanostatic deposition was used for the electrocatalytic oxidation of glucose in alkaline solutions where different electrochemical methods were employed. In cyclic voltammetry studies, in the presence of glucose an increase in the peak current of the oxidation of nickel hydroxide is followed by a decrease in the corresponding cathodic current. This suggests that the oxidation of glucose is being catalyzed through mediated electron transfer across the nickel hydroxide layer comprising nickel ions of various valence states. Under the chronoamperometric regime, the reaction followed a Cottrellian behavior and the diffusion... 

Gold nanoparticles (AuNPs) of less than 50 nm diameter were electrodeposited from cyanide solution by pulsating electric current on modified copper and indium tin oxide (ITO) films coated on glass. Morphology, size, and composition of the deposited AuNPs were studied by X-ray photoelectron spectroscopy, atomic force microscopy, and field emission scanning electron microscopy. Effects of peak current density, pulse frequency, potassium iodide and cysteine on grain size, and morphology of the AuNPs were determined. Experiments showed that cathode current efficiency increases with the pulse frequency and the iodide ion. Size of the AuNPs increased with the current density. The number of... 

The Ni-P/Zn-Ni compositionally modulated multilayer coatings CMMCs were electrodeposited from a single bath by switching the cathodic current density. The composition, surface morphology, roughness, layers growth pattern as well as the phase structure of deposits were extensively studied via SEM, EDS, AFM and XRD analysis. Effects of bath ingredients on the electrodeposition behavior were analyzed through cathodic linear sweep voltammetry. Although the concentration of Zn2+ in bath was 13 times higher than Ni2+, the Zn-Ni deposition potential was much nearer to Ni deposition potential rather than that of Zn. Addition of NaH2PO2 to the Ni deposition bath considerably raised the current... 

Nickel and nickel-manganese alloy modified graphite electrodes (G/Ni and G/NiMn) prepared by galvanostatic deposition were examined for their redox process and electrocatalytic activities towards the oxidation of methanol in alkaline solutions. The methods of cyclic voltammetery (CV), chronoamperometry (CA) and impedance spectroscopy (EIS) were employed. In CV studies, in the presence of methanol NiMn alloy modified electrode shows a significantly higher response for methanol oxidation. The peak current of the oxidation of nickel hydroxide increase is followed by a decrease in the corresponding cathodic current in presence of methanol. The anodic peak currents show linear dependency upon the... 

Nickel and nickel-copper alloy modified glassy carbon electrodes (GC/Ni and GC/NiCu) prepared by galvanostatic deposition were examined for their redox process and electrocatalytic activities towards the oxidation of methanol in alkaline solutions. The methods of cyclic voltammetery (CV) and chronoamperometry (CA) were employed. The cyclic voltammogram of NiCu alloy demonstrates the formation of β/β crystallographic forms of the nickel oxyhydroxide under prolonged repetitive potential cycling in alkaline solution. In CV studies, in the presence of methanol NiCu alloy modified electrode shows a significantly higher response for methanol oxidation. The peak current of the oxidation of nickel...