Sharif Digital Repository

The aim of the present study was to evaluate the photocatalytic degradation of anthracene using Fe-doped TiO2 nanoparticles in the presence of UV. The structure and morphology of Fe-doped TiO2 nanoparticles were studied by X-ray diffraction, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The applied nanoparticles were synthesized by the sol–gel method. The effect of influential parameters on the degradation of anthracene, including pH, time, nanopar-ticles dosage, and the concentration of anthracene was studied. Using the UV/Fe-doped TiO2 system, the optimum experimental values were obtained to be as follows: pH = 7, contact time = 60 min, anthracene concentration =... 

The degradation of methyl tert-butyl ether (MTBE) was investigated in the aqueous solution of coated ZnO onto magnetite nanoparticale based on an advanced photocatalytic oxidation process. The photocatalysts were synthesized by coating of ZnO onto magnetite using precipitation method. The sample was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and vibration sample magnetometer (VSM). Besides, specific surface area was also determined by BET method. The four effective factors including pH of the reaction mixture, Fe3O4/ZnO magnetic nanoparticles concentration, initial MTBE concentration and molar ratio of [H2O2]/ [MTBE] were optimized using response surface... 

A highly chemoselective methodology is described for the N-methylation of functionalized anilines with dimethyl carbonate (MeOCO2Me, DMC) in the presence of ZrOCl2·8H2O. Dimethyl carbonate, which usually promotes methylation at T > 120 C and eventually under inert atmosphere, was activated in the presence of zirconium oxychloride for the desired transformation at 90 C under aerobic conditions. Aminophenols showed good reactivity in this transformation and produced the corresponding N-methylanilines, as the major products, with high selectivity. Catalyst reusability study confirmed that ZrOCl2·8H2O is a recyclable catalyst and its catalytic activity was remained unchanged at least after eight... 

Catalyst layers are one the important parts of the PEM fuel cells as they are the main place for electrochemical reaction taking place in anode and cathode of the cells. The amount of catalyst loading of this layer has a large effect on PEM fuel cell performance. Non-uniformity of reactant concentration could lead to a variation of current density in anode and cathode catalyst layer. The main reason for this phenomenon is porosity variation due to two effects: 1. compression of electrode on the solid landing area and 2. Water produced at the cathode side of diffusion layer. In this study the effect of variable current density in anode and cathode electrode on cell performance is... 

A novel efficient and cost-effective heterogeneous catalyst for the production of biodiesel from transesterification of sunflower oil was prepared through the impregnation of K2CO3 upon the Talc material. The physicochemical features of the catalyst were studied through several characterization analyses. The effect of the K2CO3 loading was investigated by comparing the catalytic activity of various prepared catalysts. Moreover, the effect of the calcination temperature upon the catalytic activity was examined. To maximize the yield of the produced biodiesel fuel, reaction variables such as the reaction time and temperature, catalyst concentration, and methanol: oil molar ratio were... 

Biodiesel as an alternative fuel for fossil diesel has many benefits such as reducing regulated air pollutants emissions, reducing greenhouse gases emissions, being renewable, biodegradable and non-toxic. In this study, used frying oil was applied as a low cost feedstock for biodiesel production by alkali-catalyzed transesterification. The design of experiments was performed using a double 5-level-4-factor central composite design coupled with response surface methodology in order to study the effect of factors on the yield of biodiesel and optimizing the reaction conditions. The factors studied were: reaction temperature, molar ratio of methanol to oil, catalyst concentration, reaction time... 

Response surface methodology (RSM) was applied to optimize the process of biodiesel production from Iranian bitter almond oil. Design of experiments was performed by application of a 5-level-3-factor central composite design in order to study the effect of different factors on the product yield, biodiesel yield and biodiesel purity. These factors were reaction temperature (30-70°C), catalyst concentration (0.3-1.7% w/w) and methanol to oil molar ratio (4.4-13.6 mol/mol). A quadratic model was suggested for the prediction of the biodiesel yield. Analysis of variance revealed that the factors were significant on the production process of biodiesel. For each factor, the optimum value was... 

In the present study, we developed a multi-component one-dimensional mathematical model for simulation and optimisation of a commercial catalytic slurry reactor for the direct synthesis of dimethyl ether (DME) from syngas and CO2, operating in a churn-turbulent regime. DME productivity and CO conversion were optimised by tuning operating conditions, such as superficial gas velocity, catalyst concentration, catalyst mass over molar gas flow rate (W/F), syngas composition, pressure and temperature. Reactor modelling was accomplished utilising mass balance, global kinetic models and heterogeneous hydrodynamics. In the heterogeneous flow regime, gas was distributed into two bubble phases: small... 

Transesterification reaction was performed in the presence of soybean oil, methanol, and Demineralized water plant sedimentation catalyst at 60°C for 8 h in this study. Central composite design method was used to study the effect of catalyst concentration and methanol to oil molar ratio on purity and yield of produced biodiesel. The results showed catalyst concentration of 9.08 wt% and methanol to oil molar ratio of 22.49 as the optimum condition in which the values of purity and yield of the produced biodiesel in the second-order models were 99.89% and 81.83%, respectively. Experiments are in good agreement with the mentioned values as corresponded values are 99.95% and 86.68%,... 

In the present study, the ACF-TiO2 catalyst was synthesised and used as a catalyst for the destruction of toxic cyanide in both synthetic and real industrial wastewaters. The ACF-TiO2 catalyst was found to be micro-porous with the BET surface area of 163 m2/g. The effect of different operational parameters such as catalyst concentration, cyanide concentration, operation time, and ozone concentration were target parameters in the present study. The findings show that 500 mg/L of catalyst is the optimum value for the photocatalytical process to completely oxidise 25 mg/L of cyanide within 10 min. While it was found that 300 mg/L of catalyst in the presence of 200 mg/h ozone is enough to remove... 

Zeolite-based Ag/AgBr and Ag/AgBr/TiO 2 photocatalysts were prepared by sol-gel and deposition methods and were characterized. Their photocatalytic activities were evaluated by inactivation of Escherichia (E.) coli and the photodegradation of Acid Blue 92 and potassium permanganate. The composites containing Ag/AgBr showed the antibacterial activity in the dark by releasing Ag ions into the medium. The results for inactivation of E. coli indicated that Ag/AgBr/TiO 2 modified photocatalyst had better antibacterial activity than Ag/AgBr/zeolite, while zeolite and TiO 2/zeolite did not show any antibacterial activity under visible light and dark conditions. Photodecolarization rate was affected... 

In this work, the electrophoretic deposition method was utilized to immobilize TiO2 particles on stainless steel substrates. In addition, for the first time, statistics-based experimental design using response surface methodology was employed to investigate the effect of four key coating parameters (i.e. applied voltage, calcination temperature, photocatalyst weight percentage, and deposition time) on the photocatalytic degradation. Analysis of variance revealed that the proposed model was adequate. X-ray diffraction and scanning electron microscope were used to evaluate the effects of the parameters on degradation efficiency. The optimum applied voltage, calcination temperature, catalyst... 

Selective oxidation of H2S to elemental sulfur is a low cost and highly efficient process for sulfur removal from H2S-containing hydrocarbon streams in medium scale (i.e. 0.2–10 ton sulfur/day) for environmental protection and prevention of emitting toxic gases to the atmosphere. In this research, in order to prepare a highly active and selective nanocatalyst for selective oxidation of hydrogen sulfide, for the first time, molybdenum oxides were loaded uniformly over nitrogen- doped carbon nanotubes through incipient wetness impregnation. Different metal loadings including 5, 10, and 15 wt% Mo were considered in the synthesis procedure to achieve the optimized performance and provide... 

In the present study, a novel α-MnO2/AgI photocatalyst was successfully fabricated by using hydrothermal/precipitation methods, and its photocatalytic performance was evaluated from the degradation of Acid blue 92 (AB92) dye under visible light irradiation. The surface and crystalline structure, morphology, and electro-chemical properties of the as-made photocatalyst were investigated by BET, XRD, XPS, SEM-EDS, TEM, DRS, PL, PC, and Raman analysis. The optimized nanocomposite (α-MnO2/AgI) with a weight ratio of 1:15 showed the best photocatalytic activity in the decomposition of AB92 with a removal efficiency of 100% in 40 min which was better than that of pure α-MnO2 (48%) and AgI (61%),...