Sharif Digital Repository

In the present work, an improved method is developed for preparing highly pure ultrathin barium titanate nanostructured films with desired structural and morphological characteristics. In contrast to other approaches, our method can be carried out at a relatively lower temperature to obtain barium titanate ultrathin films free from secondary phases, impurities, and cracks. To reach an in-depth understanding of scientific basis of the proposed process, and in order to disclose the mechanism of formation and growth of barium titanate ultrathin film, in-detail analysis is carried out using XRD, SEM, FE-SEM, and AFM techniques aided by theoretical calculations. The effects of calcining... 

Anatase nanostructured coating has been prepared on 316 L stainless steel by sol-gel dip coating. The topography of the coatings surface has been analyzed using atomic force microscopy. The anticorrosion performance of the coatings has been evaluated using polarization curves. Effects of calcination temperature, withdrawal speed and times of coating on corrosion protection have been studied. The results showed calcination temperature of 400°C and withdrawal speed of 10 cm/min are desirable conditions to achieve high corrosion protection of 316 L stainless steel in chloride containing environments. Coatings with 3 times exhibit better resistance against corrosion in 0.5 molar NaCl solutions.... 

CuCo2O4 spinel nanopowders were synthesized by sol–gel method. The optimal values of pH and molar ratio of citric acid to metal ions (RC), and the influence of the calcination temperature and time were investigated. As-prepared materials were characterized by XRD, TGA, DSC, FE-SEM and electrical and coefficient of thermal expansion (CTE) measurements. It was found that pH = 4.5 and RC = 1 are the optimum conditions to produce pure CuCo2O4 nanopowders. The electrical conductivity was increased remarkably from 15.2 to 27.5 S cm−1 with an increase in temperature from 500 to 800 °C. Over the temperature range of 25–800 °C, the CTE of... 

Alumina-MWCNT composite was densified by microwave sintering. CNTs were coated with boehmite nanoparticles to enhance their distribution in composite samples. Calcination temperature of composite powder was determined by TGA analysis (5 °C/min). Samples containing 0 and 1vol%CNT were produced by cold isostatic pressing at 180 MPa. Microwave sintering (1520 °C for 45 min) was conducted under the flow of argon. Phase analysis of the calcined composite powder showed complete transformation of boehmite into gamma-alumina. The relative densities were 99.3% and 98.1% for monolithic alumina and composite, respectively. CNT addition improved the fracture toughness of alumina by ~37%. SEM images... 

The transformation of gibbsite to α-alumina occurs in the range 1100 to 1300°C. The higher the calcination temperature, the larger the crystallites and this leads to abnormal grain growth. The main goal of this research was to reduce the transformation temperature of gibbsite to α-alumina by reducing the gibbsite particles size. The sodium content of the gibbsite used in the study was reduced to less than 0.1% by washing it in HCl solution. It was then ground in a fast mill at ambient conditions for different times then calcined at different temperatures. The microstructure, particles size and thermal behaviour of the samples were examined with SEM, XRD, XRF, PSA and STA, respectively. In a... 

In this contribution, NiO-MgO-SiO2 catalyst was prepared and calcined at different temperatures of 500, 600, 700 and 800 °C. The resulting samples were characterized by BET-BJH, XRD, TPX, CO-chemisorption, EDS and SEM analyses. These were employed toward syngas production via propane dry reforming. The increment in the calcination temperature from 500 to 800 °C decreased the basicity of the catalysts. In addition, the active surface area and Ni dispersion were gradually declined by increasing the calcination temperature from 600 to 700 °C due to active metal sintering during the activation process. The calcined sample at 600 °C displayed the highest propane and CO2 conversions of 93% and 78%... 

The transformation of gibbsite to α-alumina occurs in the range 1100 to 1300°C. The higher the calcination temperature, the larger the crystallites and this leads to abnormal grain growth. The main goal of this research was to reduce the transformation temperature of gibbsite to α-alumina by reducing the gibbsite particles size. The sodium content of the gibbsite used in the study was reduced to less than 0.1% by washing it in HCl solution. It was then ground in a fast mill at ambient conditions for different times then calcined at different temperatures. The microstructure, particles size and thermal behaviour of the samples were examined with SEM, XRD, XRF, PSA and STA, respectively. In a... 

In this study hydroxyapatite (HA)/zirconia/alumina composite coatings on titanium metal was carried out using Sol-Gel dip coating and calcination process. Hydroxyapatite-Alumina-Zirconia sol, coated samples in three processes by changing final sol stirring time, aging time, calcination temperature of synthesized powder and prepared coating and rate of coating. Some parts of prepared sol were also synthesized and became powder in all three processes. Scanning electron microscopy was used to estimate the particle size of the surface and for morphological analysis. The functional group and crystallization characteristics of the powders were analyzed using (FTIR) and X-Ray diffraction (XRD).... 

A hydrogen-selective nano-composite ceramic membrane was prepared by depositing a dense layer composed of SiO2 and Al2O 3 on top of a graded multilayer substrate using co-current chemical vapor deposition (CVD) method. The multilayer substrate was made by dip-coating a macroporous α-alumina tubular support by a series of boehmite solutions to get a graded structure. Using DLS analysis, it was concluded that decreasing hydrolysis time and increasing acid concentration lead to smaller particle size of boehmite sols. XRD analysis was carried out to investigate the structure of intermediate layer and an optimized calcination temperature of 973 K was obtained. SEM images indicated the formation... 

Yttrium Iron Garnet (YIG) powders were synthesized by a sol-gel auto-combustion method using cationic and anionic surfactants with different values and different calcination times and temperatures. The final products were characterized by DTA/TG, XRD, TEM and VSM techniques. The results showed a decrease in calcination temperature and crystallite size in the presence of a cationic surfactant, while no significant effect was observed using an anionic surfactant. Magnetic properties of YIG powders were improved as an optimum value of cationic surfactant was used  

The main purpose of this study is to prepare and characterize hydroxyapatite (HA)-10%wt bioglass (BG) composite nanopowders and its bioactivity. Composites of hydroxyapatite with synthesized bioglass are prepared at various temperatures. Suitable calcination temperature is chosen by evaluating of the phase composition. X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Scanning electron microscopy (SEM) techniques are utilized to characterize the prepared nanopowders. The bioactivity of the prepared composite samples is evaluated in an in vitro study by immersion of samples in simulated body fluid (SBF) for predicted time. Fourier transformed infrared (FTIR) spectroscopy and... 

Using a combined hydrothermal and sol-gel route, TiO 2 -capped ZnO nanoparticles with an average size of 60 nm were prepared. The titania shell was amorphous with a thickness of ∼10 nm. Formation of Zn 2TiO 4 phase at higher calcination temperature was noticed. Effects of Ti/Zn molar ratio and coating time on the thickness of TiO 2 shell and the photoactivity of the particles for decolorization of Methylene Blue (MB) under UV lamp irradiation (3 mW/cm 2) were investigated. The nanoparticles were characterized by X-ray diffraction, transmission electron microscopy, fourier-transform infrared spectrometry (FTIR), diffuse reflectance spectroscopy (DLS), and atomic absorption spectroscopy.... 

Quartz is usually detected as an impurity of kaolinite clays. The present work attempts to evaluate the role and behaviour of quartz particles in geopolymerisation and its probable effects on mechanical behaviour of geopolymeric products. Two kaolinite clays with different free quartz contents were used as raw materials to produce geopolymers. Results showed that using high content quartz kaolin causes higher compressive strength. Scanning electron microscopy studies confirmed that quartz does not participate in geopolymerisation and completely remains in the structure as fine particles. High hardness quartz particles by retarding crack growth in the geopolymer matrix enhance mechanical... 

Barium strontium titanate (BST) was prepared via the simple sol-gel method by using tetrabutyl ti-tanate, ethanol, citric acid and ethylene glycol as starting materials. Thermogravimetry and differential thermal analysis were used to examine the behaviour of the xerogel. The particle size of BST was approximately 21 nm, as calculated by the X-ray diffraction and confirmed by transition electron microscopy for the calcination temperature of 750 °C. It was found that the particles of BST powders calcined at 750 °C were smaller and more homogeneous and uniform than those obtained at 800 °C  

LiNiO2 powders were synthesized with acrylic acid, citric acid, oxalic acid, and triethanolamine (TEA) as a chelating agent. Crystallized LiNiO2 was synthesized in air at a calcinations temperature of 500 °C for 12 hours, when the molar ratio of chelating agents to total metal ion (RPM) was 1.0. The TEA-assisted method had the highest intensity ratio of (003)/(104) peaks of X-ray diffraction (XRD) spectrum. The transmission electron microscopy (TEM) analysis indicates that the sample prepared with triethanolamine obtained the smallest particle size with average particle size of only 12nm. The results indicate that chelating agents have an important role in the intensity ratio of (003)/(104)... 

In this research, a solid 1%Li/Ca-La mixed oxide catalyst was prepared using co-precipitation method followed by wet impregnation. The prepared catalyst was used in the transesterification reaction of canola oil and methanol for biodiesel synthesis. The effects of calcination and reaction temperatures were investigated on the activity of the catalyst. In addition, rate of the reaction was studied through a kinetic model for which parameters were determined. Surface properties and structure of the catalyst were characterized through the powder X-ray diffraction (XRD), thermogravimetry/derivative thermogravimetry (TG/DTG), and Fourier transform infrared spectroscopy analysis. All these... 

In this research, the propane steam reforming (PSR) as a promising alternative route over a mesoporous NiO–MgO–SiO2 catalyst to produce syngas (SG) was undertaken. This catalyst was prepared using a co-precipitation method followed by hydrothermal treatment. The influence of such catalyst preparation factors as the hydrothermal time and temperature, pH and calcination temperature on the physicochemical characteristics of the prepared samples were examined. Next, these materials were characterized through the BET-BJH, XRD, TPR, and FTIR analyses. The thermal stability of this catalyst was tested through the TGA and DTA techniques. Furthermore, the deactivation of the calcined catalysts at... 

In the present work, the novel ternary Fe2O3/MoO3/AgBr photocatalyst with different dosages of AgBr was successfully synthesized via a facile method. The physicochemical properties of the resultant catalyst were characterized by using various techniques such as XRD, SEM, EDX, BET, XPS, DRS, and VSM. The photocatalytic performance of as-prepared samples was evaluated by degradation of organic dye acid blue 92 (AB92) under visible light irradiation, and in dark. The impact of different operating parameters namely calcination temperature, amount of photocatalyst, dye concentration, and pH of solution were investigated in degradation reaction. Ternary nanocomposite exhibited the best... 

A novel efficient and cost-effective heterogeneous catalyst for the production of biodiesel from transesterification of sunflower oil was prepared through the impregnation of K2CO3 upon the Talc material. The physicochemical features of the catalyst were studied through several characterization analyses. The effect of the K2CO3 loading was investigated by comparing the catalytic activity of various prepared catalysts. Moreover, the effect of the calcination temperature upon the catalytic activity was examined. To maximize the yield of the produced biodiesel fuel, reaction variables such as the reaction time and temperature, catalyst concentration, and methanol: oil molar ratio were...