Sharif Digital Repository

A glassy carbon electrode was coated with a thin layer of multi-walled carbon nanotubes and subsequently was electro-polymerized with polypyrrole. The prepared electrode was used for the voltammetric determination of olanzapine (OLZ). The peak current of OLZ increases remarkably on the surface of the modified electrode. This is due to the large increase in the microscopic area of the electrode surface along with the strong adsorption of OLZ on the surface of the electrode. The film modifier was characterized by scanning electron microscopy, atomic force microscopy and cyclic voltammetry techniques. Experimental variables, such as deposited amount of nanotube suspension, pH of the supporting... 

Molecular dynamics (MD) simulation was used to study of thermal properties of NiTi/Cu. Embedded atom method (EAM) potentials for describing of inter-atomic interaction and Nose-Hoover thermostat and barostat are employed. The melting of the bi-layers was considered by studying the temperature dependence of the cohesive energy and mean square displacement. To highlight the differences between bi-layers with various copper layer thickness, the effect of copper film thickness on thermal properties containing the cohesive energy, melting point, isobaric heat capacity and latent heat of fusion was estimated. The results show that thermal properties of bi-layer systems are higher than that of... 

Hydrothermal and in-situ polymerization methods were used to successfully fabricate a pompon flower-like CoGd0.5Fe1.5O4 (CG) as a magnetic component and a cauliflower-like poly(indole-co-Py) (PP) co-polymer as a dielectric component for microwave absorption. The physico-chemical properties of CG/PP samples were determined via XPS, XRD, FTIR, BET, UV–vis, EDS, and FESEM analysis. VNA and VSM were used to evaluate the dielectric and electromagnetic properties of the CG and PP samples. The results of the absorption capability tests revealed that bi-layer samples outperformed single layer samples in terms of microwave dissipation capability. The thickness and arrangement of each layer in bilayer... 

The present study is focused on the investigation of the absorption properties of the bi-layer absorber with different thickness and orientation approaches. Improvement in absorption exclusively depends on the various parameters as interfacial polarization, multiple reflections among layers, conduction loss, phase cancellations, and shape anisotropy, etc. By considering these parameters. Calcium titanate micro-cubes CaTiO3 (CTO) and polypyrrole nanotubes (PPy) nanocomposites were prepared and microwave absorption from single layer coaxial absorbers having M1 = CaTiO3+15 wt% polymer and M2 = CaTiO3+30 wt% polymer were determined. Different layer orientations and thicknesses of the bi-layer... 

The behavior of Alsteel bilayer sheets produced by cold roll welding is investigated through the wedge tearing process. It is observed that through tearing the energy absorbed by cold roll welded bilayer sheets is larger than that of non-welded ones, even though all parameters are identical. Also bilayer sheets with low bond strength have the same energy absorbed by non-welded bilayer sheets. By investigating all contributing mechanisms in tearing and mechanical properties of composite layers and developing theoretical equations, it is concluded that bending of sheets through wedge tearing plays a major role in difference of energy absorbed by welded and non-welded bilayer sheets. Moreover,... 

The effect of the layer in contact with tool (Al or Cu) and the depth of plunge on friction stir butt welding of Al-Cu bilayer laminated composites produced by cold roll welding were studied. The measurement of weld cross sections and variations of the axial load and torque during welding process showed that material flow is influenced by the material which is in contact with the shoulder. Being Al layer in contact with the shoulder led to higher force and torque during welding, and a defect-free weld could be obtained in this manner. By welding from Cu side, a higher plunge depth was needed to develop enough force and torque and thereby a defect-free weld. The amount of material swept by... 

Herein, two distinct nanocomposites of CaTiO3 micro-cubes and polygonal SrFe12O19, both decorated with NiO nanoparticles, were successfully synthesized using hydrothermal method. The physico-chemical features of as-prepared samples were evaluated via XRD, FTIR, UV–vis, BET, XPS, FESEM and EDS analysis. Microwave attenuation features of as-prepared single layer absorbers were determined by VNA analysis in 2–18 GHz. Simulation confirmation was checked by preparing a bi-layer samples and evaluating it using VNA analysis after finding the appropriate thickness of each layer. The reflection loss from each single layer samples containing 20 wt% of each CaTiO3/NiO and SrFe12O19/NiO nanocomposites... 

There has been a growing demand for materials with superior absorption capabilities, such as strong absorbing capacity, thin thickness, and light weight, to solve challenges related to EM radiation pollution. While the majority of the research is focused on optimizing material compositions, component microstructure and absorber structure are also critical factors for improving microwave absorption performance. In this research, we show how the microstructure of components and absorber design may increase dissipation features. Solvothermal and hydrothermal methods were utilized for synthesizing mesoporous CuS micro-particles with a 3D hierarchical structure as a dielectric component and... 

Al-1100/St-12 aluminum clad steel sheets were produced using roll bonding process at different reductions in thickness and with various supplemental annealing treatments. Experiments were conducted by applying the Taguchi method to obtain optimum condition for maximizing the joint strength. The joint strengths of the bi-layer sheets were evaluated by peel test. The Al/Fe intermetallic phases at the joint interface and the peeled surfaces were examined using scanning electron microscopy (SEM). Energy dispersive spectroscopy (EDS) and Vickers microhardness test were performed to characterize the intermetallic compounds. The results indicate that at the optimum condition of 0.50 reduction in... 

The mechanism of interface formation during sinter-joining of nanostructured yttria stabilized zirconia (27 nm) compacts with chromium powder was investigated. The effect of sintering atmosphere, i.e. argon or vacuum, was studied. Microstructural evaluation and phase formation was examined by scanning electron microscopy (SEM), electron probe micro-analysis (EPMA), and micro-focused X-ray diffraction (MFXRD) methods. It is shown that spreading and evaporation-condensation mechanisms are responsible for the interface formation. An improved joint shear-strength was obtained after sintering in vacuum (74 MPa) compared with argon (41 MPa). The result of MFXRD indicated formation of Cr-island at... 

This paper presents a comparative study of plasticity and fracture behavior of the NiTi/Ag bilayer for the different crystallographic orientations of the substrate. Molecular dynamic (MD) simulation was used to determine the deformation mechanism, dislocation density, plastic energy dissipation and delamination of the NiTi/Ag bilayers near the interface, when NiTi aligned at (1 0 0), (1 1 1), (1 1 0), (3 2 1), (2 1 0) and (2 1 1) faces during the cyclic-nanoindentation test. The Griffith energy balance model was used to estimate the energy release associated with the delamination. The results of the simulation are suggested the dependence of deformation mechanism, energy release rate (Gin),... 

In planar perovskite solar cells (PSCs), engineering the extraction and recombination of electron–hole pairs by modification of the electron transport layer (ETL)/perovskite interface is very vital for obtaining high performance. The main idea here is to improve properties of the TiO2/perovskite interface by inserting an ultra-thin layer (UTL) of WO3 or SnO2 with the thickness of less than 10 nm by RF magnetron sputtering method. The structural and electrical characteristics of the samples were tested by XRD, AFM, FE-SEM, Mott-Schottky analysis, UV–Vis spectroscopy, J-V characterization and electrochemical impedance spectroscopy (EIS). It was found that the bilayer structured ETLs exhibit... 

A key direction toward managing extrinsic instabilities in perovskite solar cells (PSCs) is encapsulation. Thus, a suitable sealing layer is required for an efficient device encapsulation, preventing moisture and oxygen ingression into the perovskite layer. In this work, a solution-based, low-cost, and commercially available bilayer structure of poly(methyl methacrylate)/styrene-butadiene (PMMA/SB) is investigated for PSCs encapsulation. Encapsulated devices retained 80% of the initial power conversion efficiency (PCE) at 85 °C temperature and 85% relative humidity after 100 h, while reference devices without SB (only PMMA) suffer from rapid and intense degradation after only 2 h, under the... 

The lipid membranes of living cells form an integral part of biological systems, and the mechanical properties of these membranes play an important role in biophysical investigations. One interesting problem to be evaluated is the effect of protein insertion in one leaflet of a bilayer on the physical properties of lipid membrane. In the present study, an all atom (fine-grained) molecular dynamics simulation is used to investigate the binding of cytotoxin A3 (CTX A3), a cytotoxin from snake venom, to a phosphatidylcholine lipid bilayer. Then, a 5 ms coarse-grained molecular dynamics simulation is carried out to compute the pressure tensor, lateral pressure, surface tension, and first moment... 

A promising electrochemical sensor was developed based on a layer by layer process by electro-polymerization of pyrrole in the presence of new coccine (NC) as dopant anion on the surface of the multi-walled carbon nanotubes (MWCNTs) pre-coated glassy carbon electrode (GCE). The modified electrode was used as a new and sensitive electrochemical sensor for voltammetric determination of sumatriptan (SUM). The electrochemical behavior of SUM was investigated on the surface of the modified electrode using linear sweep voltammetry (LSV). The results showed a remarkable increase (∼12 times) in the anodic peak current of SUM in comparison to the bare GCE. The effect of experimental variables such... 

Stepwise-graded composite layer of M2 tool stel and 17-4PH stainless steel was fabricated by a simple powder layering technique and the isothermal and nonisothermal sintering response of the bilayer were examined. It was shown that the materials exhibit poor compatibility during co-sintering, i.e., the amount of mismatch shrinkage is significant. An improved compatibility was obtained by adding 0.2 wt% B to the stainless steel powder. Formation of relatively dense layer at the bonding zone indicated an enhanced densification rate at the interface. Microstructural studies showed formation of a ferritic interface in M2/17-4PH composite and elongated grains with an intergranular boride phase... 

Herein, two distinct nanocomposites of CaTiO3 micro-cubes and polygonal SrFe12O19, both decorated with NiO nanoparticles, were successfully synthesized using hydrothermal method. The physico-chemical features of as-prepared samples were evaluated via XRD, FTIR, UV–vis, BET, XPS, FESEM and EDS analysis. Microwave attenuation features of as-prepared single layer absorbers were determined by VNA analysis in 2–18 GHz. Simulation confirmation was checked by preparing a bi-layer samples and evaluating it using VNA analysis after finding the appropriate thickness of each layer. The reflection loss from each single layer samples containing 20 wt% of each CaTiO3/NiO and SrFe12O19/NiO nanocomposites... 

We report optical and electrical properties of Cu-Ni nanoparticles in hydrogenated amorphous carbon (Cu-Ni NPs @ a-C:H) with different surface morphology. Ni NPs with layer thicknesses of 5, 10 and 15 nm over Cu NPs @ a-C:H were prepared by co-deposition of RF-sputtering and RF-Plasma Enhanced Chemical Vapor Deposition (RF-PECVD) from acetylene gas and Cu and Ni targets. A nonmetal-metal transition was observed as the thickness of Ni over layer increases. The surface morphology of the sample was described by a two dimensional (2D) Gaussian self-affine fractal, except the sample with 10 nm thickness of Ni over layer, which is in the nonmetal-metal transition region. X-ray diffraction profile... 

Recently, co-powder injection molding process (2C-PIM) has attained considerable interest to fabricate complex-shaped functional materials. The aim of this work is to study the sintering compatibility between nanocrystalline yttria-stabilized zirconia (3Y-TZP) and PIM grade 430L stainless steel (SS) powders, which is the utmost important step in the 2C-PIM process. To evaluate the mismatch strain development during the co-sintering, the isothermal and nonisothermal behaviors of the ceramic and metal powders were studied. Small bilayers of 3Y-TZP/430L were made by a powder metallurgy technique and the feasibility of simultaneous sintering and joining of the composite layer was examined.... 

There are high attractions in the development of conducting polymer (CP) coatings to improve the electrochemical properties and biocompatibility of electrodes in the area of biosensors. A new type of the modified electrodes is prepared in a layer-by-layer process by using multi-walled carbon nanotube (MWCNT) and poly-pyrrole. In this procedure, the glassy carbon electrode is casted by a drop suspension of MWCNT, which leads to form a thin film of nanotube on its surface. In the second step, electrochemical polymerization of pyrrole in the presence of tiron (used as doping anion) is performed on the surface of the MWCNT pre-coated electrode. The modification procedure led to fabrication of a...