Sharif Digital Repository

In this paper, the compressible gas flow through a pipe subjected to wall heat flux in unsteady condition in the entrance region is investigated numerically. The coupled conservation equations governing turbulent compressible viscous flow in the developing region of a pipe are solved numerically under different thermal boundary conditions. The numerical procedure is a finite-volume-based finite-element method applied to unstructured grids. The convection terms are discretized by the well-defined Roe method, whereas the diffusion terms are discretized by a Galerkin finite-element formulation. The temporal terms are evaluated based on an explicit fourth-order Runge-Kutta scheme. The effect of... 

An efficient algorithm for the design optimization of the compressible fluid flow problem through a flexible structure is presented. The methodology has three essential parts: first the behavior of compressible flow in a supersonic diffuser was studied numerically in quasi-one-dimensional form using a flux splitting method. Second, a fully coupled sequential iterative procedure was used to solve the steady state aeroelastic problem of a flexible wall diffuser. Finally, a robust Genetic Algorithm was implemented and used to calculate the optimum shape of the flexible wall diffuser for a prescribed pressure distribution. © 2006 Elsevier Ltd. All rights reserved  

The configuration of landmarks is an important issue in minimizing the target registration error (TRE). In this paper the effect of different landmark configurations on the accuracy of pedicle screw placement during image guided spine surgery (IGSS) is investigated. Since the spine is deformed in intra-operative conditions compared to the preoperative situation, an accurate alignment of each vertebra is crucial to compensate for the deformation. CT compatible markers are placed over anatomical landmarks which are feasible and routinely used in surgical procedures. The TRE is obtained directly for the markers which are placed on the right and left pedicle of the vertebra. The estimated TRE... 

Purpose: The accuracy of pedicle screw placement during image-guided spine surgery (IGSS) can be characterized by estimating the target registration error (TRE). The major factors that influence TRE were identified, minimized, and verified with in vitro experiments. Materials and methods: Computed-tomography- compatible markers are placed over anatomical landmarks of lumbar vertebral segments in locations that are feasible and routinely used in surgical procedures. TRE was determined directly for markers placed on the pedicles of vertebra segments. First, optimum selections of landmarks are proposed for different landmarks according to the minimum achievable TRE values in different... 

The authors' research work on pressure drop along gas transmission pipelines raised questions regarding the development length of the corresponding compressible flow and the effect of heat transfer in the entrance region on the pressure drop along the whole length of the pipe. In this paper, laminar, viscous, compressible flow in the entrance region of a pipe is investigated numerically in two dimensions. The numerical procedure is a finite-volume based finite-element method applied on unstructured grids. This combination together with a new method applied for boundary conditions allows accurate computation of the variables in the entrance region. The method is applied to some incompressible... 

The wellhead flow control valve bodies which are the focal point of this failure case study were installed in some of the upstream facilities of Khangiran's sour gas wells. These valve bodies have been operating satisfactorily for 3 years in wet H2S environment before some pits and cracks were detected in all of them during the periodical technical inspections. One failed valve body was investigated by chemical and microstructural analytical techniques to find out the failure cause and provide preventive measures. The valve body alloy was A216-WCC cast carbon steel. During investigation many cracks were observed on the inner surface of the valve body grown from the surface pits. The results... 

Effects of microstructure and texture, before and after phase transformation, on the anisotropy of the mechanical properties and fracture behaviors of commercially pure titanium were studied. Before phase transformation, due to the split distribution of basal texture the activation of different deformation systems led to mechanical properties anisotropy. Although the fracture mechanism in both specimens was voids nucleation, growth and coalescence, the shape, size and distribution of dimples were affected by active deformation systems. However, after phase transformation, basal plains in most grains were aligned with the transverse direction. This texture component led to the activation and... 

Simultaneous effects of thickness and texture on the anisotropy of mechanical properties and fracture behaviors of commercially pure titanium thin sheets were studied. The activation of different deformation systems, due to the split distribution of basal texture, led to mechanical properties anisotropy. The crack initiation and propagation energies, when the loading direction was parallel to the initial rolling direction, decreased with increasing thickness ranges from 0.25 to 1 mm. The changes of size, shape and distribution of dimples with increasing thickness confirmed the restriction of deformation systems and the development of triaxial stress state and plane-strain condition at the... 

An experimental study of wear characteristics of electroless Ni-10% P coating sliding against hard AISI 52100 steel pin is investigated. Experiments are carried out at room and 550°C temperatures. Heat treatment effects on tribological behavior of this coating are studied. The wear surface and the microstructure of the coatings are analyzed using optical microscopy, scanning electron microscopy, energy dispersion analysis X-ray, and microhardness testing equipment. It is observed that the forming of continuous oxide film on contacting surfaces of pin and disk improves wear resistance and decreases friction coefficient of the Ni-10% P coating. The results indicate that the wear resistance of... 

The wellhead flow control valve bodies which are the focal point of this failure case study were installed in some of the upstream facilities of Khangiran's sour gas wells. These valve bodies have been operating satisfactorily for 3 years in wet H2S environment before some pits and cracks were detected in all of them during the periodical technical inspections. One failed valve body was investigated by chemical and microstructural analytical techniques to find out the failure cause and provide preventive measures. The valve body alloy was A216-WCC cast carbon steel. During investigation many cracks were observed on the inner surface of the valve body grown from the surface pits. The results... 

The environmental impact of asbestos fibers on human health and their consequent safety-related problems indicate that there is a significant need to replace this material in all asbestos-containing products. Many different types of fibers have been introduced to replace asbestos fibers. In this study, the performance of silica nano-particles combined with waste paper pulp fibers (sulfite fibers) has been investigated. Different mechanical (compressive and flexural strengths and bending performance), durability (water absorption), physical (bulk density and flowability), and microstructural (scanning electron microscopy) tests were conducted to examine the properties of manufactured green... 

In the present work tensile and tear properties of commercially pure titanium with different rolling reductions and specimens directions were investigated. The experimental results showed that in low levels of deformation the microstructure refining and mechanical twins have fewer significant effects on the anisotropic behavior of both tear and tensile properties and the crystallographic texture controls the mechanical properties anisotropy. The increase in rolling reduction up to 50% led to the formation of strong-basal texture and resulted in the activation of almost same deformation systems and isotropic mechanical response. However, at high levels of deformation, due to the split... 

Local annealing of amorphous NiTi thin films was performed by using an Nd:YAG 1064 nm wavelength pulsed laser beam. Raw samples produced by simultaneous sputter deposition from elemental Ni and Ti targets onto unheated Si (100) and Silica (111) substrates were used for annealing. Delicate treatment with 15.92 W/mm2 power density resulted in crystallization of small spots; while 16.52 and 17.51 W/mm2 power densities caused ablation of the amorphous layer. Optical microscopy, scanning electron microscopy, X-ray diffraction and atomic force microscopy were performed to characterize the microstructure and surface morphology of the amorphous/crystallized spot patterns  

Simultaneous effects of notch and texture on strengthening mechanisms of rolled thin sheets of commercially pure titanium were investigated. The presence of notch led to the restriction of deformation systems and different fracture behaviors compared to un-notched specimens. The loss of material's ability to accommodate plastic deformation at the notch tip with increase in rolling reductions changed the notch strengthening phenomenon to the notch weakening one. At medium levels of deformation, due to the simultaneous development of a triaxial stress state and strong basal texture at the notch tip, a new strengthening mechanism which is called "notch-texture strengthening mechanism" led to a...