Sharif Digital Repository

With increasing number of processors on a chip, the role of interconnections becomes more important in both power consumption and bandwidth. As a result, in MultiProcessor System-on-Chip architectures, the design constraints will shift from "Computational Constraints" to "Communicational Constraints". Nowadays, optical information transfer is introduced as a suitable substitution for electrical interconnections in chips, which can eliminate their problems. Many different optical networks have been presented so far. These networks can be divided into two subcategories. Networks of the first category use an electrical infrastructure as well as optical one. Hence, the scalability of scheme is... 

Considering the advantages of heterogeneous catalysts for the easy work up procedure, being eco-friendly, and the reusability, herein, two projects are carried out by metal-supported SBA-15 catalysts. The first one is the oxidative deprotection of trimethylsilyl ethers catalyzed Cr (VI) in the presence of TBHP as oxidant. In this project, trimethylsylil ethers are oxidized in good to high yields. The second project is the oxidative coupling of thiols to disulfides catalyzed by Fe (III) in the presence of hydrogenperoxide. This catalyst/oxidant system convets different aromatic thiols to corresponding disulfides efficiently  

Hadron therapy is one of the cancer treatment methods using the targeted dose distributhion. In hadron therapy, the prompt gamma is produced from excited nucleas of target in the following of non-elastic nuclear interactions between the target and the incident proton within few nano-seconds and with energy less than 10 MeV. The excited energy level depends on incident particle energy and the target materials. Since the Spatial distribution of prompt gamma rays depends on incident particles energy, it can be useful for determinding the incident particle range. Also, the prompt gamma energy spectrum of each element is an individual feature, thereby targets with different composition of... 

Platinum nanotubes were deposited inside the pores of polycarbonate template with the pore size of 200 nm by electrochemical methods. In this regard a solution containing of 0.05 M H2PtCl6 and 0. 1 M H2SO4 in doubly distilled water was utilized. The electrodeposition process was studied by electrochemical techniques such as voltammetry and chronoamperometry methods. It was observed that the process was conducted in several stages including; nucleation and growth in steady state regime. Furthermore, it was concluded that electrodeposition was affected by mass transport restriction and was controlled by a diffusion process. In this regard, all the voltammograms were shifted to more negative... 

Vehicular ad-hoc networks have attracted the attention of many researchers during the last years due to the emergence of autonomous vehicles and the safety concerns regarding their use in near future. One of the major applications in this domain is the usage of vehicle to vehicle communication for warning message dissemination in dangerous situations to prevent more damage. A number of schemes have been proposed regarding the selection of forwarding nodes in this application and there is a need for developing frameworks for analysis and comparison of the schemes in fair situation. Most of the proposed frameworks make use of simulation techniques for the analysis of schemes. However, due to... 

In order to investigaton of dynamics behavior and determination of the aeroelastic stability of the turbomachine blade. the turbomachine blade is modeled by using the beam model, taking into account all degrees of freedom, the effect of warping, rotation and seting angle. For aerodynamic modeling, the Smith and Whitehead models are used which are valid in subsonic flow. The validity of the derived formulation is confirmed through comparison with those obtained from the finite element software and the available results in the literature. Then, by using the state feedback controller, the effect of sensor and piezoelectric actuator on the vibrations reduction of the structure and increasing the... 

Increasing population growth and scarcity of fresh water resources have created the challenge of water supply, especially in the Mena region. Thus, many countries in the region have turned to innovation in the development of high-energy seawater desalination technologies. Utilizing the waste heat of refineries in the desalination industry can reduce costs and preserve the environment. In this article, effective ways to use the waste heat of other flue recovery steam of Bandar Abbas oil refinery are investigated. The integration of the heat recovery system consisting of recuperative heat exchangers and heat pipes with thermal desalination plants is investigated by multi-stage flash and... 

Power amplifiers are used as the last block of transmitters. This block can be categorized as the one of most important part in communication systems. However, in transmitter systems which require high power to create stable link with the receivers, fabrication process like CMOS are unable to provide such level of power. Thus, designers employ another group of integrated circuits which names MMIC that offers this capability to designers. MMIC is the abbreviation of Microwave Integrated Circuit which is implemented in compound substrates like GaAs. Monolithic microwave integrated circuits enable the implementation of amplifiers in small size, large number, with high precision and appropriate... 

Today Ethernet is the predominant technology for implementing Local Area Networks. Its privileges encourage service providers to extend Ethernet from Local Area Networks to Metropolitan Area Networks or even Wide Area Networks. Ethernet benefits such as low operational costs, well interoperability, plug-n-paly characteristic and rapid provisioning on demand make Ethernet ideal for Metropolitan Area Networks.But Ethernet by itself has some weakness like flat structure that makes it unfit for use in Metropolitan Area Networks. A suitable solution for taking advantages of Ethernet benefits in service provider network is using Ethernet in access network and applying multi-point to multi-point... 

Paper and cardboard waste pulping consume large volumes of water, so the discharge of this effluent without proper treatment can have far-reaching environmental consequences. The color and variable COD concentration of wastewater in this industry make treating this wastewater complicated. Therefore, this study aims to reduce the COD of the wastewater treatment plant of a pulp and paper mill under different laboratory conditions to achieve environmental standards in Iran.In this study, coagulation-flocculation and the Fenton process on the wastewater entering the treatment plant were investigated first. It was found that coagulation and flocculation by 750-1250 ppm of alum coagulant and ten... 

This thesis aim to the study of the effect of bank’s branching decisions on deposit market. Using panel data banks from Iran, we study effect of branching on market share and market size. In theoretical part, we assume that banks maximize discounted flow of the profits. We also assume that the banks take into account the reaction from rival banks in setting number of branches. Banks are assumed to expect the rival banks react by a lag of one period. In empirical part, in order to distinguish between aggregate market size effect and market share effect, we rewrite quantity of deposit in banks as the product of aggregate deposit and market share. We specify deposit market share function with... 

Selective Laser Melting (SLM) process is a powder-based metal Additive Manufacturing (AM) technique. This developing industry has many advantages like generation of geometrically complex shapes with high density. High Cost, production and characterization of powders, limited material choices and process parameters optimization are some of the challenges associated with SLM. Stainless steel 316L due to its unique properties, like corrosion resistance, high strength, biocompatibility, availability and cost is indeed a commonly used material in SLM. In this research, the characterization of the powder produced by the flame spraying device, which is a new method, was discussed. Wire with 3mm...