Sharif Digital Repository

In this study, different concentrations of ascorbic acid (50, 100 and 200 μg/mL) were added to the liquid phase of a calcium phosphate cement (CPC). The cements were immersed in simulated body fluid (SBF) for different intervals and physical, physicochemical and mechanical properties of them were evaluated. The release of added ascorbic acid from CPCs into the SBF solution was also studied. From the results, both setting time and injectability of CPC decreased by adding ascorbic acid, however the compressive strength was sharply increased before soaking in SBF solution. But, the compressive strength values of all cements (with or without ascorbic acid) soaked in SBF solution for more than 7... 

In the present study, bioceramic composites based hydroxyapatite (HAp) reinforced with carbon nanotubes (CNTs) was synthesized via sol-gel technique. The dried gels were individually heated at a rate of 5°C/min up to 600°C for 2 h in a muffle furnace in order to obtain HAp-MWCNTs mixed powder. Composites were characterized by XRD, FT-IR, SEM, TEM/SAED/EDX and Raman spectroscopy techniques. Results showed the synthesis of HAp particles in the MWCNTs sol which was prepared in advance, leads to an excellent dispersion of MWCNTs in HAp matrix. Apparent average size of crystallites increased by increasing the percentage of MWCNTs. The average crystallite size of samples (at 600°C), estimated by... 

This investigation focused on a comparison between hydroxyapatite (HA) and carbon-nanotube-reinforced hydroxyapatite composite (CNTs/HA) coatings. The HA and CNTs/HA composite (with 5wt% CNTs) coatings were prepared with the sol-gel method on 316L stainless steel. Phase evaluation by means of XRD and Raman spectroscopy was performed on the HA and CNTs/HA composite coatings. The coatings were immersed in simulated body fluid (SBF) in order to evaluate the biological properties of the coatings. During the first week of immersion, the increase in the amount of Ca2+ precipitation in the SBF when CNTs/HA was used was lower than for the HA coatings. This behavior can be related to the difference... 

Different concentrations of CaF2 were incorporated in mica glass-ceramics to evaluate their effects on the crystallization and microstructure. The kinetics of phase transformations, and the microstructures of the final crystalline phase were found to be dependent on the concentration of nucleation agents. The results showed that CaF2 in high concentration had a synergistic effect and enhanced the formation of interlocked mica crystals. Non-isothermal DTA experiments showed that the crystallization activation energies of base glasses were changed in the range of 235-405 kJ/mol, while the crystallization activation energies of samples with addition of CaF2 were changed in the range of 419-747... 

The present work studied bioactive coatings on the surface of ceramic biomaterials. Zirconia toughened alumina (ZTA) composites containing 15 mol.-%. Partially stabilised zirconia was prepared after 1 h sintering at 1550°C. Apatite layers were then coated onto the surfaces of composites by the biomimetic method using 1·5-2 multiply concentrations of simulated body fluid (SBF). Before treatment in SBFs, a sodium silicate layer was employed as nucleating agent to induce the formation of a calcium phosphate layer. The effect of immersion time on the morphology of the precipitate was monitored with a scanning electron microscope. X dot maps revealed that there is a relationship between... 

Formation of machinable glass-ceramic in the system MgO-SiO 2-Al2O3-K2O-B2O 3-F with and without addition of MgF2 has been investigated. Crystallization of glass sample was done by controlled thermal heat treatment at nucleation and crystallization temperatures. The results showed that MgF2 in high concentration had a synergistic effect and enhanced the formation of interlockedmica crystals. Non-isothermal DTA experiments showed that the crystallization activation energies of base glasses were changed in the range of 235-405 kJ/mol, while the crystallization activation energies of samples with addition of MgF2 were changed in the range of 548-752 kJ/mol  

Physical properties of low cement castable containing 22 wt.% Al 2O3-rich MgO-Al2O3 spinel and 1.7 wt.% CaO with addition of polyacrylates, castament FS20, TPP and citric acid were investigated. Results showed castables including castament FS20 have higher flow values and better final properties comparing with castables including Darvan 7S and TPP. Also in this study we investigated the effect of addition of microsilica up to 4 wt.% on the properties of alumina-spinel castables. Microsilica is the finest particles in the system and due to suitable distribution of microsilica among other particle the open porosity reduced and mechanical strength increased. Slag penetrations resistance... 

Formation of transparent glass-ceramic in the system MgO-SiO 2-Al 2O 3-K 2O-B 2O 3-F with and without addition of LiF and NaF has been investigated. Crystallization of glass-sample was conducted by controlled thermal heat-treatment, at determined nucleation and crystallization temperatures. In this regard, the effects of addition of LiF and NaF were investigated on the crystallization behavior and transparency of the samples. Low transmission (less than 80% at 600. nm) was observed in the basic composition (K).The addition of NaF and LiF caused more intense phase separation in the system. The results indicated that the glass-ceramic can remain transparent if fine grains with nano size are... 

The influence of Zr 2 on the crystallization behavior, microstructure, and machinability of SiO 2-Al 2O 3-MgO-K 2O-B 2O 3-F glasses was investigated. The crystallization of the glass-ceramic was markedly affected by addition of ZrO 2. These glasses crystallize more rapidly. The number of mica crystals increases, whereas the size of the mica crystals decreases drastically. Machining of these glass-ceramics was found to be good, as confirmed by a drilling test using conventional steel tools. Such mechanical properties are attributable to the microstructure of these glass-ceramics. Very fine crystals are homogeneously distributed in glass matrix  

Recent investigations show that ceramic/ceramic joints have high potential for applications in industry. Cost and difficulty in manufacturing complex components, either in one step or by joining of ceramic-metal and ceramic-ceramic, have inhibited more widespread use. It is important to know how to join components without problems and to understand the role of the interface as the main factor controlling the properties in these joints. The purpose of this paper was to investigate the joining of two ceramics with metal fillers (SiC to SiC and Al2O3 to Al2O3) and to investigate the interface of SiC/SiC and Al2O3/Al 2O3 with the same metal interlayer (Ag-Cu-Ti) and the effects on the... 

Electrical conductivities in dark and light were investigated in Calcium doped Bismuth Ferrite thin films. Higher dark conductivity, in the order of 10 times higher than conductivity of bismuth ferrite, was observed for Bi 0.85Ca0.15FeO3 - δ. Structural analyses using Rietveld refinement showed a deviation from volume reduction for Bi 0.85Ca0.15FeO3 - δ which could be the reason of abnormally high conductivity for this compound. Although higher calcium doping reduced conductivity, photoconductivity was observed again. Atomic Force Microscopy investigations showed that surface roughness and grain size decreased with increasing calcium concentration. Enhanced photoconductivity is reported for... 

Abstract Porous lead zirconate titanate-lead cobalt niobate 0.8Pb(Zr1/2Ti1/2)O3-0.2Pb(Co1/3Nb2/3)O3 (PZT-PCN) piezoelectric ceramics were fabricated by introducing pore-forming agent polymethyl methacrylate (PMMA), and the effect of sintering behavior on their microstructure, dielectric, and piezoelectric properties were investigated. The optimum sintering procedure was designed according to the thermogravimetric analysis of pore former. Finally the electrical properties were measured. The porosity of PZT-PCN ceramics decreased and the grain size increased with an increase in the sintering temperature at a fixed PMMA addition. "An increase in density with sintering temperature from 1050 to... 

M-type Ce–Co substituted barium hexaferrite nanoparticles were synthesized by sol–gel auto-combustion route. The general formula of ferrites was Ba1−xCexFe12−xCoxO19 in which the x was considered to be: x = 0, 0.1, 0.2, and 0.3. The formed phases in the samples were characterized by using X-ray diffraction, Fourier transform infrared spectroscopy, Mössbauer spectroscopy and vibrating sample magnetometer. The results indicated that an increase in substitutional ion amount caused to decrease vibration frequencies of Fe–O band in the tetrahedral site due to the substitution of heavier Co2+ ion for Fe3+ ion in the tetrahedral site. Moreover, some of Ce3+ ions was transformed to Ce4+ and... 

Porous PZT-PCN ceramics were fabricated with this formula, “0.8 Pb(Zr1/2Ti1/2)O3-0.2 Pb(Co1/3Nb2/3)O3”, abbreviated as “PZTPCN” by introducing Polyvinyl chloride(PVC) and stearic acid (SA) as pore forming agents (PFA) with varied percentages (5, 10 and 15 wt%). The optimum sintering procedure was designed according to the thermogravimetric analysis of pore formers. XRD and FESEM were applied to study the formed phase and the microstructure of the system. Electrical Characterization was conducted using Piezo meter. A decrease in density reduced longitudinal piezoelectric coefficient (d33) and relative dielectric constant (ε) and enhanced hydrostatic figure of merit (dhgh) of PZTPCN ceramics.... 

In this study, the crystallisation of nano hydroxyapatite (HA) films on stainless steel 316L was studied. The film was prepared by sol-gel technique. The process was started with preparation of an HA sol. After aging of the sol at room temperature, a stainless steel 316L substrate was dip coated and then was heat treated from 350 to 450°C at different periods of time in air. The crystallisation behaviour and the transformation-temperature-time diagram of HA films were achieved and analysed using the avrami equation. The results showed that the crystallisation of HA began at 250°C and was increased up to 450°C. The obtained HA film showed a nanostructure character with a suitable crystalinity... 

Zirconia Toughened Alumina (ZTA) Nanocomposites were prepared using Nano sized Zirconia (ZrO2) powders doped with 3% mol of yttria (Y 2O3) nanopowders. Diffusion of α-alumina (Al 2O3) nanoparticles as well as yttria into the Zirconia lattice network drives monoclinic - tetragonal martensitic transformation. Zirconia toughened alumina (ZTA) composites containing different amount of partially stabilized Zirconia (PSZ) 5, 10, 15 and 20% mol, were prepared via wet mixing and axial pressing. After sintering at different temperatures,1450, 1550 and 1650 °C, phase change in the samples were monitored. X-ray diffraction patterns showed that at constant composition, tetragonal zirconia was increased... 

Solid oxide fuel cells (SOFCs) are rapidly becoming recognized as a new alternative to traditional energy conversion systems because of their high energy efficiency. From an ecological perspective, this environmentally friendly technology, which produces clean energy, is likely to be implemented more frequently in the future. However, the current SOFC technology still cannot meet the demands of commercial applications due to temperature constraints and high cost. To develop a marketable SOFC, suppliers have tended to reduce the operating temperatures by a few hundred degrees. The overall trend for SOFC materials is to reduce their service temperature of electrolyte. Meanwhile, it is... 

In this research, cold compaction behavior and pressureless sinterability of WC, WC-10%wtCu and WC-30%wtCu powders were investigated. WC and WC/Cu powders were milled in a planetary ball mill for 20h. The milled powders were cold compacted at 100, 200, 300 and 400 MPa pressures. The compressibility behavior of the powders was evaluated using the Heckel, Panelli-Ambrosio and Ge models. The results showed that the PanelliAmbrosio was the preferred equation for description the cold compaction behavior of the milled WC and WC-30%wtCu powders. Also, the most accurate model for describing the compressibility of WC-10%wtCu powders was the Heckel equation. The cold compacts were sintered at 1400oC.... 

Barium hexaferrite (BaFe12O19) nanoparticles were synthesized by sol–gel auto-combustion route. Prepared samples were sintered at 950 and 1100 °C with Fe3+/Ba2+ = 12 and 20 mol ratio. The formation mechanism of barium hexaferrite was investigated by using X-ray diffraction (XRD) and differential scanning calorimetry (DSC) analyses. In addition, the effect of temperature and Fe3+/Ba2+ mole ratio on BaFe12O19 formation and magnetic properties, and the effect of increasing the Fe3+/Ba2+ upon gel ignition and subsequent phase development were investigated. Finally the magnetic behavior was monitored with VSM. DSC studies showed that pure barium hexaferrite phase was formed from maghemite... 

A nanocomposite of Ce-doped TiO2-reduced graphene oxide (CedT/RGO) was synthesized to evaluate the synergistic effects of constituents on electrical and photoelectric properties. The nanoparticles of titania and CedT were synthesized via the sol-gel method. Then, RGO was prepared using a new version derived from the Hammer's method and hydrothermal methods. Finally, CedT/RGO nanocomposite was synthesized applying hydrothermal method. The nanoparticles and nanocomposite were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, Field emission scanning electron microscopy (FESEM), Energy dispersive X-ray spectroscopy and elemental mapping. Then, diffuse reflectance and...