Sharif Digital Repository

Abstract: Surface-nanostructured TiO2 nanorods were synthesized hydrothermally at 180 °C. Such nanorods have ‘crack-like’ surfaces that resemble burnt charcoal. Compared to nanorods with relatively smoother surfaces, the charcoal-like nanorods have higher-specific surface areas. By using the nanorods as a light-scattering layer in double-layered dye-sensitized solar cells, the cells based on the charcoal-like nanorods have 20 % higher dye loading and also higher diffuse reflectance compared with cells utilizing ‘smooth’ nanorods. The efficiency of a screen-printed double-layer dye-sensitized solar cell based on the charcoal-like nanorods is higher at 7.29 %. Electrochemical... 

Morphology tailored TiO2 nano assemblies consisting of nanorods with and without nanoparticle attachments were hydrothermally synthesized and their characteristics and light scattering properties were determined by x-ray diffraction (XRD), nitrogen sorption analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), electrochemical impedance spectroscopy (EIS) and ultraviolet-visible spectroscopy (UV-Vis). The nanorod-nanoparticles (NR-NP) assemblies and smooth nanorod (NR) double layers were screen printed onto fluorine doped tin oxide coated glass underlayers to fabricate dye-sensitized solar cell (DSSC) photoanodes. The double layer heterogeneous... 

This paper reports a simple, low-cost, and effective electrochemical technique for sensing and reducing CrVI based on a Au-Pd bimetallic nanoparticle (BNP)-decorated indium tin oxide (ITO) conducting glass electrode. It was observed that the Au-Pd BNP-decorated ITO electrode could significantly boost the electrochemical reduction of CrVI when compared with either Au nanoparticle- or Pd nanoparticle-decorated ITO electrodes. These BNP-decorated electrodes exhibited a wide linear concentration range of 0.001-100 μM, a very low detection limit (signal-to-noise ratio = 3) of 0.3 nM, and a high sensitivity of 1.701 μA μM-1. From electrochemical impedance spectroscopy, it was revealed that this... 

Oriented ZnO nanorods were grown directly on fluorine doped tin oxide substrates by a single bath electrodeposition process. A pulse potential at the beginning of growth improved the density and orientation of the nanorods. Pulse potential grown ZnO nanorod films showed better harvesting of visible light and enhanced the light driven water splitting performance in comparison to nanorods grown without any pulse potential. To further improve the water splitting activity, the nanorods were decorated with gold–palladium nanoparticles by sputtering. This caused visible light absorption to increase due to a plasmonic effect and the photoelectrochemical water splitting performance to further... 

Enhancing stability against photocorrosion and improving photocurrent response are the main challenges toward the development of cupric oxide (CuO) based photocathodes for solar-driven hydrogen production. In this paper, stable and efficient CuO-photocathodes have been developed using in situ materials engineering and through gold-palladium (Au-Pd) nanoparticles deposition on the CuO surface. The CuO photocathode exhibits a photocurrent generation of ∼3 mA/cm2 at 0 V v/s RHE. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) analysis and X-ray spectroscopy (XPS) confirm the formation of oxygen-rich (O-rich) CuO film which demonstrates a highly stable photocathode with retained... 

Abstract: Here, the synthesis of TiO2 rutile nanorod arrays (TiO2 NRs) decorated with bimetallic gold–palladium cocatalyst nanoparticles (AuPd NPs) is described. The modified photoelectrode was characterized by field-emission scanning electron microscopy, high-resolution transmission electron microscopy, energy-dispersive spectroscopy, X-ray diffraction analysis, X-ray photoelectron spectroscopy, UV–vis spectroscopy, and electrochemical impedance spectroscopy (EIS). AuPd–TiO2 NRs (AuPd–TiO2) demonstrate high photocatalytic activity for photoelectrochemical (PEC) water splitting. The tailored structure of AuPd–TiO2 depicts a boosted photocurrent of 3.36 mA cm−2 under AM 1.5 illumination...