Sharif Digital Repository

PID Neural Network controller design for Sharif University of Technology (SUT) Building Energy Management System (BEMS) is addressed in this paper. The most important characteristics of process systems are time delay with model uncertainties. Artificial neural networks can perform adaptive controller properties through learning processes. FID neural network has the advantages of both conventional PID controllers and the neural structure. Simulation results using Modified Hooke-Jeeves Optimization Method show that this controller has short convergence time and quick learning speed and the performance of the closed loop system is very good. © 2005 IEEE  

The estimation of the wind resource at the hub height of a wind turbine is one of the primary goals of site assessment. Since in a majority of cities the wind speed is measured at lower heights, the power law model is applied to estimate the wind speed at higher heights. In this study, the wind data for 10 cities in Iran have been analyzed over a period of one year. The accuracy of the power law model to estimate the wind speed has been examined with variations of height and time during this year. The energy production of a wind turbine using the measured wind speeds and the speeds estimated by the power law model were compared. The measured data revealed that in some cities the wind speed... 

We develop accurate analytical relations for the droplet volume ratio, droplet length during breakup process, and pressure drop of asymmetric T junctions with a valve in each of the branches for producing unequal-sized droplets. An important advantage of this system is that after manufacturing the system, the size of the generated droplets can be changed simply by adjusting the valves. The results indicate that if the valve ratio is smaller than 0.65, the system enters a nonbreakup regime. Also the pressure drop does not depend on the time and decreases by increasing the valve ratio, namely, opening the degree of valve 1 to valve 2. In addition, the results reveal that by decreasing... 

Due to significant reduction in fossil fuel sources, several researches have been conducted recently to explore modern sources of renewable energy. One of the major fields in the category of renewable energy harnessing devices is parabolic trough solar collector (PTC). Several parameters have effect on the overall efficiency of the PTCs. As the effect of these parameters is coupled to each other, a comprehensive investigation is necessary. In the present study, a numerical analysis is performed to examine the efficiency of PTCs via variation of several governing parameters (e.g., wind velocity magnitude, nanoparticles volume fraction, inlet temperature, and reflector's orientation). A... 

Droplet-based microfluidic logic gates have many applications in diagnostic assays and biosciences due to their automation and the ability to be cascaded. In spite of many bio-fluids, such as blood exhibit non-Newtonian characteristics, all the previous studies have been concerned with the Newtonian fluids. Moreover, none of the previous studies has investigated the operating regions of the logic gates. In this research, we consider a typical AND/OR logic gate with a power-law fluid. We study the effects of important parameters such as the power-law index, the droplet length, the capillary number, and the geometrical parameters of the microfluidic system on the operating regions of the... 

The use of superhydrophobic surfaces is one the most promising methods for reducing the friction and increasing the flow rate in fluid transfer systems. Because in such systems the surface structure plays a key role, in this study, we explore the performance of the hierarchical nanostructures. These nanostructures are inspired by the superhydrophobic surface of the lotus leaf. We consider a flow between two walls with hierarchical nanostructures and simulate the system via the molecular dynamics method. The size of the nanostructures and the distance between them have been studied to find whether a design with a maximum flow rate exists. The nanostructures have two parts, a bigger part on... 

Droplet breakup in symmetric T-junctions is one of the important phenomena in droplet microfluidics. Many studies have been done about the droplet breakup but none of them has provided a general analytical solution for the droplet breakup. In this study, we present an analytical solution to investigate the effect of important parameters such as the capillary number, droplet length, and channel widths ratio. The analytical solution is validated using the numerical simulation. Using the analytical equation and numerical results, we propose a generalized relationship. This general equation can be used as a rule of thumb for droplet breakup predictions with high accuracy. The results indicate... 

Superhydrophobic surfaces have been used for reducing friction in micro- and nanochannels. In the present work, water flow between two carbon walls with nanostructures made of poly(N-isopropylacrylamide) via the molecular dynamics method has been studied. The structure of this polymer can change based on the temperature of the environment, so that by increasing the temperature the structure becomes hydrophobic. This property has been studied and the effect of multiple factors on the slip length is presented. The effects of the number of monomers in the polymer, the distance between the polymers, and the temperature on the flow field are investigated. The results reveal that the slip length... 

Water can be pumped in nanochannels by limiting it between the surfaces with different hydrophobicities and exerting a spinning electric field. The asymmetrical hydrophobicity combined with the spinning electric field and the fact that the water molecules have a dipole moment create a situation in which the angular momentum of water molecules is transformed into a linear momentum and the water is pumped into the nanochannel. The hydrophobicity of the surfaces can be manipulated by using nanostructures to reduce friction. In this study, two types of nanostructures have been used which are hierarchical nanostructures and polymer nanostructures made of Poly(N-isopropylacrylamide). The walls of... 

Three-dimensional cell culture and the forming multicellular aggregates are superior over traditional monolayer approaches due to better mimicking of in vivo conditions and hence functions of a tissue. A considerable amount of attention has been devoted to devising efficient methods for the rapid formation of uniform-sized multicellular aggregates. Microfluidic technology describes a platform of techniques comprising microchannels to manipulate the small number of reagents with unique properties and capabilities suitable for biological studies. The focus of this review is to highlight recent studies of using microfluidics, especially droplet-based types for the formation, culture, and... 

The present paper is an account of an experimental analysis carried out to investigate to what extent the flow characteristics in the intake system of a 4-valve, spark ignition internal combustion engine depend on the experimental conditions at the steady flow test bench. In this respect, the study is aimed at determining the influences of the intake adaptor, test pressure, adaptor length and diameter, adaptor roughness, paddle wheel diameter, and asymmetric valves lifting on the flow coefficient and the swirl intensity measurements. In studies of this kind, researchers generally tend to adopt different test parameters to arrive at a nonuniform base to compare results from several... 

Thermal load simulation and sensitivity analysis are performed for a building in Tehran by numerical means. A heat conduction equation of the walls, together with appropriate convection and radiation boundary conditions, is simulated numerically to compute temperature distributions in the walls. This research proposes a heat balance method, coupled with a bulk model, to calculate the building thermal load. In the first step, the results of the building thermal load for weather data of Tehran are compared and validated with those of Carrier HAP software, and a good agreement is found between them. The building thermal load depends on the boundary conditions of the building. The influence of... 

This paper investigates the efficiency and performance of several of the fiooding techniques popular in secondary and enhanced oil recovery. These processes include water fiooding, immiscible and miscible gas fiooding, and several forms of water-alternating-gas (WAG) injection. The study is carried out numerically on a typical one-dimensional domain using an advanced high-resolution central scheme. Some performance indices such as oil cut drop, breakthrough time, and sweep efficiency were employed to evaluate the appropriateness of each injection strategy  

In this study, a novel pseudo-three-dimensional model is developed to find out both fluid and solid temperature distributions in multi-stream plate fin heat exchangers. In this simulation algorithm, heat exchangers can be in either parallel flow or cross flow configuration. The model considerations include: heat leakage of cap plates and side plates, conduction throughout the solid matrix of the heat exchanger, variable physical properties, and inlet mass flow rate maldistribution. Using the computational code, the effects of different factors such as: the number of layers, mass flow variation, inlet mass flow rate maldistribution, and stacking pattern on the thermal performance of the heat... 

Compact heat exchangers are among the vital components used in various industries. In this study, a general framework has been developed with a multi-scale point of view for three-dimensional simulation of multi-stream plate-fin heat exchangers. The most important features in the MSPFHEs simulation, such as phase change phenomena, multi-component mixtures, multiple streams, transversal, lateral and longitudinal conduction, non-uniformity of inlet flow, variable fluid properties, and heat leakage are simultaneously considered in this model. The modular form of the model structure has facilitated layer-by-layer simulation of cross flow heat exchangers as well as parallel flow ones. Our model... 

In spite of numerous attempts which have been made during the last decade to optimize pulse tube refrigerators, still theoretical and analytical realization of this device needs to be thoroughly explained. In this paper, in addition to the oscillatory flow analysis in the pulse tube refrigerator through a simple analytical model, the performance of the alternate tube section of this device is analyzed using a generalized efficiency, based on the entropy generation rate. In this model, in order to extract the entropy generation rate and the dissipative terms caused by fluid friction and heat flow in alternate tube, simplified momentum and energy equations are solved analytically and velocity... 

Multi-stream Plate-fin heat exchangers (MSPFHEs) are among the most efficient heat exchangers in energy-based industries. They should be carefully designed to have maximum effectiveness and to avoid wasting energy. Flow maldistribution could significantly degrade the performance of heat exchangers. This study presents a novel modeling framework to capture the thermally-induced maldistribution in two-phase MSPFHEs. The developed model is used to show how thermally-induced flow maldistribution affects the performance of the heat exchanger, and some possible modifications are investigated to reduce its consequences. Our case study results show that thermally-induced maldistribution decreases... 

Model Reference Adaptive Controller (MRAC) design, for Sharif University of Technology (SUT) Building Energy Management System (BEMS) is addressed in this paper. A reference model with fuzzy adaptive control rules was employed to design the controller for a system with time delay and model parameter uncertainties. Simulation study shows good performance of the closed loop system with optimum energy consumption for this system under external load disturbance. Copyright © 2005 by ASME  

Access to potable water with standard quality is an inevitable component of human's lives. Freeze desalination, by consuming lower energy compared to other techniques, relies on the exertion of a cold source which is then accompanied by simultaneous rejection of impurities from water. Regarding this, a numerical study on freeze desalination in a hollow cylinder is carried out to determine the effects of the design variables such as heat flux, hydraulic diameter, initial salt concentration, and freezing time on the ice mass, ice salinity, ice generation speed, and Nusselt number on the cold surface of the inner tube. Results show that increasing the value of heat flux from −250 [Formula... 

An analytical solution is presented to study the heat transfer characteristics of the combined pressure - electroosmotically driven flow in planar microchannels. The physical model includes the Joule heating effect to predict the convective heat transfer coefficient in two dimensional microchannels. The velocity field, which is a function of external electrical field, electroosmotic mobility, fluid viscosity and the pressure gradient, is obtained by solving the hydrodynamically fully-developed laminar Navier-Stokes equations considering the electrokinetic body force for low wall zeta potentials. Then, assuming a thermally fully-developed flow, the temperature distribution and the Nusselt...