Sharif Digital Repository

The demand for independent power generation has been increased in recent years due to the growing demand in distributed networks, losses and power qaulity in power systems. These losses occur in transmission to distribution networks from the generation sites to the end-user loads which have harmonic losses besides fundamental losses.. The non-linear load makes the harmonics flow in the line and create the harmonic losses. However, in a distributed network with several DGs of different types and with all kinds of variable nature loads, an optimal power balance in the system has to be achieved. This optimal objective, which results in minimal energy losses over a specific period of time,... 

In this work, a model was presented for an MCFC fuel cell with internal reforming and combustion chamber. The model consists of mass and heat transfer equations beside the chemical and electrochemical reaction rate equations. Velocity distribution due to reactions and temperature distribution along the cell is considered. The model has been simulated in steady state form using finite difference method in MATLAB package environment accompanied by the analysis of the dynamic behavior of cell using method of lines in Simulink environment. Simulation results have been validated with experimental data extracted from literature. The last part of the work concerns with sensitivity analysis of some... 

The need to supply energy of low voltage electronic circuits such as sensors and wireless systems has attracted many researchers in recent years. As a solution to this problem, the energy needed for electronic devices can be obtained from the surrounding environment. An important part of energy harvesters are the systems that use vibrating energy of mechanical devices known as vibration power generators. Most linear vibration generators are systems that operate in resonance mode. As the frequency of the environment moves away from the natural frequency of the generator, the amount of converted energy decreases significantly. For this reason, some solutions are needed to solve this problem. ... 

This thesis is focused on the preparation and use of polysaccharides as extractive phases in various extraction methods, such as the micro solid phase extraction (µ-SPE), needle trap microextraction (NTME) and thin film microextraction (TFME).In the first research, feasibility of the online µ-SPE method using cellulose acetate (CA) fibers was investigated. For this purpose, CA fibers were prepared by electrospinning technique and then placed into µ-SPE cartridge. With this method, it was possible to simultaneously extract the drug compounds in the urine and plasma samples. The enrichment factor and limits of detection (LODs) were obtained in the range of 194-210 and 1.0-2.4 μg L-1,... 

Due to both dynamic and opportunistic spectrum access, Cognitive radio networks is a promising solution for spectrum scarcity problem. In cognitive radio networks, users need to have a control channels in order to cooperate for sharing the sensing information, channel sharing and etc. In Ad-hoc cognitive radio networks because of the absence of infrastructure and central nodes, every user runs a distributed algorithm to create a common control channel. If the control channel gets jammed, network’s performance degrades dramatically, therefore the jammer’s target in cognitive radio networks is the control channels to disturb the networks’ performance. The traditional solution to confront... 

By far, the most expensive part of the production optimization process is the evaluation of the objective function because this requires computationally expensive reservoir simulations to be performed.One way to reduce this high computational cost isby using surrogates or proxies for the reservoir simulator. There are different methods for constructing a surrogate that their aims are mimicking the reservoir behavior with high accuracy and low computational cost. In reservoir engineering surrogate modeling has been used for the problem of well placement optimization,while in the context of production optimization it has not yet been investigated in the literature. Moreover, most of surrogate... 

One of the important questions in mathematics is generalized. In case of metric spaces, one of the questions is: Can we extend notions of Riemannian geometry to arbitrary metric spaces smoothly? Ricci curvature is one of the most important concepts in differential geometry. Ricci curvature is defined for the Riemannian manifold and has many applications in mathematics and physics like Einstein’s equation in relativity theory. There is a good notion for a metric space having “sectional curvature bounded below by K” or “sectional curvature bounded above by K”, due to Alexandrov. Can we define the concept of Ricci curvature in metric space? A motivation for this question comes from Gromov’s... 

Seismic design codes reduce loads by using response modification factor. Because of the reserved strength in structural elements and capacity of structure to dissipate energy, structures can be designed for lower seismic loads. This factor has modified over time. In this thesis, the effect of the reduction in behavior factor on the response of two kinds of reinforced concrete systems were evaluated. Moment resisting frames and dual systems with different heights and regularity in plan, heve been design according to the behavior factor which is recommended in the 3rd edition of the Iranian codes of practice for seismic resistance design of buildings (Standard No. 2800). Drift and... 

Generally, nowadays, machine learning methods are used in many different areas for their superiority over other methods of prediction. Although being a tough task, stock market prediction with machine learning approaches is being spread due to satisfying results published ever yday. Machine learning methods usually use varied kinds of data ,including structured data such as market data, technical indicators and some fundamental data as well as unstructured one entailing text and graph data in order to enhance their predictability capacity. In this thesis we aimed to find out more about the importance and the contribution of structured data in prediction and we tried to attain a framework... 

This thesis presents an inventory control system which is based on Meta-heuristic Algorithms.In this thesis we will optimize the input values of our tree-echelon inventory model (keeping costs,stock worth,reorder costs,...) with these Algorithms. The presented method is able to determine the optimal stock level, costs of system and number of shipments in the system. The method is basically a decision support system (DES) and it is able to provide the order scheduling parameters of goods at operational level. The aim of the current research is to demonstrate that a Meta-heuristic algorithmis capable of solving complex inventory problems and with future improvements it is able to achieve... 

Reinforced concrete bridge columns located in regions of high seismicity are designed with large ductility capacity for adequate protection against collapse. This type of design tends to result in large permanent displacements. To maximize post-event operability and to minimize repair costs, new design strategies to reduce these residual displacements are necessary. Even though seismic codes ensure life safety for bridges, large residual displacement after severe earthquake may make the bridge useless. For example, after 1995 Hyogo-ken Nanbu earthquake (Japan), more than 100 reinforced concrete bridge columns experienced a tilt angle of more than 1 degree (1.75% drift). These columns had to... 

The new lateral load resisting system introduced in this dissertation is a kind of squat composite shear wall consisting of a concrete core as filler and two steel corrugated sheets as cover. Reinforced bars are not used in this kind of construction. Load resisting process of the walls is provided by 3 factors: concrete core, steel corrugated covers on both sides of the central core and shear-friction interaction between the core and covers. There is not any specific formula for their design because of their novelty and few researches on this kind of walls and absence of code provisions. In this project, squat composite walls were constructed with dimensions of 106.8×90 (cm2) from corrugated...