Loading...
Search for:
ghasemi--ali
0.118 seconds
Total 2605 records
Impact of Net Stress on Stress State of an Unsaturated Sand
, M.Sc. Thesis Sharif University of Technology ; Khosravi, Ali (Supervisor)
Abstract
Results of an advanced suction controlled triaxial test device in an attempt to define the constitutive relationship between suction stress and matric suction (Suction Stress Characteristic Curve, SSCC) for unsaturated sand was presented. The suction stress is a macroscopic stress that incorporates the effects of capillary van der Waals forces cementation, and electrical double-layer repulsion into the definition of effective stress for unsaturated soils. Results of previous studies on silt and clay indicated that variations in the suction stress, during drying path had a non-linear increasing trend with matric suction with greater values upon wetting. However, due to different material...
Investigation Effect of Nano- sized Additives on Microstructure and properties of MgO-CaO Refracrories
, M.Sc. Thesis Sharif University of Technology ; Nemati, Ali (Supervisor)
Abstract
Magnesia–Doloma refractories are considered as a mixed product of alkali products i.e. sintered (fused) magnesia and doloma in which 50-80 wt% magnesia is contained. These refractories enjoy some advantages such as high slag resistance corrosion, high-temperature performance, potential for production of pure molten iron and low cost due to abundance of magnesia and doloma resources in access. However, there exist some problems with these refractories that render them unsuitable for some applications. Among these cases, poor resistance of hydration can be cited that may constrain the amount of this refractory in various industrial applications. In the present work, the addition effect of...
Evaluation of Magnetic and Microwave Absorption Properties of Sr-Hexaferrite Nano Particles Doped With Zn and Ti
, M.Sc. Thesis Sharif University of Technology ; Nemati, Ali (Supervisor) ; Ghasemi, Ali (Supervisor)
Abstract
In this study, the micro and nano particles of substituted strontium hexaferrites with nominal composition of SrFe12-xTix/2Znx/2O19 (x=0, 0.5, 1, 1.5, 2 and 2.5) were prepared by a co-precipitaion method. Ferrite-PVA composites (70:30) with thickness of 1.8mm were prepared at 220°C and 50Mpa. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), energy dispersive spectrometer (EDS), vibrating sample magnetometer (VSM) and vector network analyzer (VNA) were employed for characterization of synthesized powders and composites. XRD and FTIR results showed that single phase hexaferrite were obtained for almost all of the...
Adaptive and Fast Forwarding in Named Data Networks
, M.Sc. Thesis Sharif University of Technology ; Movaghar, Ali (Supervisor)
Abstract
Named Data Networking (NDN) is a revolutionary architecture for the future Internet. The existence of a large number of unbounded and variable-length names in NDN requires substantial re-engineering of network architecture, especially for name lookup which is key to NDN routers. In this paper, we propose a novel NDN structure – called Fast-Come-Fast-Served (FCFS) – for fast, scalable, and memoryefficientlookup. To the best of our knowledge, this is the first optimized structure that employs Deterministic FiniteAutomaton (DFA) for Longest Prefix Matching (LPM) in NDN. The strengths of arrays and hash tables as core data structures are combined to make FCFS fast and cache-friendly. The NDN...
Design and Simulation of a Novel Mechanism for Energy Harvesting from Sea Waves
, M.Sc. Thesis Sharif University of Technology ; Selk Ghaffari, Ali (Supervisor) ; Zohour, Hassan (Supervisor)
Abstract
Ocean waves are a huge, renewable energy resource, and the potential for extracting energy from waves is high. So a lot of different systems have been designed but most of them are hydraulically and have a lot of problems and they are very complex. In this thesis, the mechanism designed is purely mechanical and very simple and innovative. It has some gears in special combination with together. The mechanism can convert any form of oscillation to rotation movement; this event has been shown in results and prototype. According to the results and discussion, Designed mechanism needs very low maintenance and has low lost. So, efficiency is between 80-95%
Design and Manufacturing of One Degree of Freedom Worm Robot
, M.Sc. Thesis Sharif University of Technology ; Meghdari, Ali (Supervisor) ; Ghasemi Oskouei, Kambiz (Co-Advisor)
Abstract
Nowadays, worm robots are widely designed and manufactured for different applications. The most common applications for these types of robots can be mentioned as maintenance of small pipes and medical purposes in biological vessels such as the lungs, intestines, urethra and blood vessels. The robot must be small, controllable, safe, reliable, energy efficient, and must be able to crawl both, forward and backward. Different worm robots have been developed and manufactured, for different purposes such as, medical and industrial applications. Most of these projects are typically designed with three or more actuators for control of the distance between cells and the clamps.The results of using...
Study of Light Depolarization in Biological Tissue by Means of the Monte Carlo Simulation
, M.Sc. Thesis Sharif University of Technology ; Amjadi, Ahmad (Supervisor) ; Ansari, Mohammad Ali (Supervisor)
Abstract
In this project, polarization properties, intensity of reflected light, by one layer tissue that has specified optical properties has been investigated by means of Monte Carlo simulation. Fresnel's coefficients were considered in this simulation too. The incident beam was assumed very thin with specified wave length and linear polarization parallel to plane of incidence.This beam was radiated from origin to the tissue vertically. The layer consists of homogenous particles with defined radius. Concentration of particles was constant. 10000 photons with specified weight were launched to tissue in each simulation. The results of reflected light from tissue showed that variation of the size and...
Fatigue Behavior of Al-SiC Nanocomposite
, M.Sc. Thesis Sharif University of Technology ; Simchi, Abdolreza (Supervisor) ; Ekrami, Ali Akbar (Supervisor)
Abstract
Recently, mechanical properties of advanced materials such as nanostructured and ultra-fine materials and especially nanocomposites were studied by lots of researcher. In this study, fatigue behavior of Al-SiC nanocomposites is observed. Ultra-fine grains Al matrix nanocomposites reinforced with 50 nm diameter SiC nanoparticles were produced by milling and hot extrusion. For this purpose, pure aluminum powder was mixed with 2, 4 and 6 Vol. % of SiC nanoparticles and then milled by planetary mill. The milled powder then were degased in an Argon atmosphere furnace, cold pressed and then hot extruded. Closed die-hot forging was used with about 18.8% reduction in cross section in order to...
Parallelized numerical modeling of the interaction of a solid object with immiscible incompressible two-phase fluid flow
, Article Engineering Computations (Swansea, Wales) ; Volume 34, Issue 3 , 2017 , Pages 709-724 ; 02644401 (ISSN) ; Nikbakhti, R ; Ghasemi, A ; Hedayati, F ; Malvandi, A ; Sharif University of Technology
2017
Abstract
Purpose - A numerical method is developed to capture the interaction of solid object with two-phase flow with high density ratios. The current computational tool would be the first step of accurate modeling of wave energy converters in which the immense energy of the ocean can be extracted at low cost. Design/methodology/approach - The full two-dimensional Navier-Stokes equations are discretized on a regular structured grid, and the two-step projection method along with multi-processing (OpenMP) is used to efficiently solve the flow equations. The level set and the immersed boundary methods are used to capture the free surface of a fluid and a solid object, respectively. The full...
Oscillating pipe flow: High-resolution simulation of nonlinear mechanisms
, Article 2006 ASME Joint U.S.- European Fluids Engineering Division Summer Meeting, FEDSM2006, Miami, FL, 17 July 2006 through 20 July 2006 ; Volume 1 SYMPOSIA , 2006 , Pages 1-10 ; 0791847500 (ISBN); 9780791847503 (ISBN) ; Sharif University of Technology
American Society of Mechanical Engineers
2006
Abstract
A new perspective suitable for understanding the details of nonlinear pumping (formation of traveling shocks) inside a pressurized cavity is constructed in this paper. Full compressible axisymmetric three-dimensional Navier-Stokes equations are used as the starting point to cover all complexities of the problem that exceedingly increase for particular ranges of Mach, Reynolds and Prandtl numbers. Then a very high-order numerical method is introduced to preserve the user-defined order of accuracy for practical simulations. For removal of spurious waves, higher-order compact filters are derived. All equations are marched in time using the classical Runge-Kutta algorithm which is appropriate...
An optimized large-stencil approach for capturing near-PI frequencies
, Article 12th AIAA/CEAS Aeroacoustics Conference, Cambridge, MA, 8 May 2006 through 10 May 2006 ; Volume 5 , 2006 , Pages 3010-3022 ; 1563478099 (ISBN); 9781563478093 (ISBN) ; Sharif University of Technology
American Institute of Aeronautics and Astronautics Inc
2006
Abstract
Large-stencil schemes which their spectral properties are acceptable in the vicinity of ω = π are analyzed for the first time. A machine independent model for evaluating the efficiency of generalized time-marching finite-difference algorithms over periodic domains is developed. This model which is based on operation count reveals that for small values of Total Computational Cost(TCC), the previous low-order small-stencil schemes are more efficient while for moderate TCC, the efficiency of optimized large-stencil schemes abruptly increases. This important result is the motivation for developing optimized large-stencil schemes. The current schemes are successfully implemented in a full...
Numerical solution of high-frequency oscillations of a gas column using a modified lax-wendroff scheme
, Article International Conference on Noise and Vibration Engineering 2006, ISMA 2006, Heverlee, 18 September 2006 through 20 September 2006 ; Volume 4 , 2006 , Pages 2191-2199 ; Sharif University of Technology
Katholieke Universiteit Leuven
2006
Abstract
Recently, several high-order accurate methods have been developed for solving nonlinear equations governing in the high-frequency oscillations of a fluid column. If we assume that the value of Reynolds and Prandtl numbers are high enough then it is possible to neglect the effect of Stokes Layer and it has been previously shown that the calculated pressure profile obtained by solving three-dimensional axisymmetric compressible NS (Navier-Stokes) equations is in good agreement with one-dimensional adiabatic model of Ilinskii. For this particular flow which is the typical of engineering flows inside acoustical compressors, it is clear that high-resolution simulation of NS equations in higher...
Oscillating pipe flow: high-resolution simulation of nonlinear mechanisms
, Article 2006 2nd ASME Joint U.S.-European Fluids Engineering Summer Meeting, FEDSM 2006, Miami, FL, 17 July 2006 through 20 July 2006 ; Volume 2006 , 2006 ; 0791837831 (ISBN); 9780791837832 (ISBN) ; Sharif University of Technology
2006
Abstract
A new perspective suitable for understanding the details of nonlinear pumping (formation of traveling shocks) inside a pressurized cavity is constructed in this paper. Full compressible axisymmetric three-dimensional Navier-Stokes equations are used as the starting point to cover all complexities of the problem that exceedingly increase for particular ranges of Mach, Reynolds and Prandtl numbers. Then a very high-order numerical method is introduced to preserve the user-defined order of accuracy for practical simulations. For removal of spurious waves, higher-order compact filters are derived. All equations are marched in time using the classical Runge-Kutta algorithm which is appropriate...
Facile synthesis and simulation of MnO2 nanoflakes on vertically aligned carbon nanotubes, as a high-performance electrode for Li-ion battery and supercapacitor
, Article Electrochimica Acta ; Volume 390 , 2021 ; 00134686 (ISSN) ; Abnavi, A ; Ghasemi, F ; Ghasemi, S ; Sanaee, Z ; Mohajerzadeh, S ; Sharif University of Technology
Elsevier Ltd
2021
Abstract
This study reports the successful fabrication of high-performance flexible binder-free lithium-ion battery anode and supercapacitor based on the synthesis of 3D hierarchical MnO2 nanoflakes (NFs) on vertically aligned carbon nanotubes (VACNTs) grown upon stainless steel (SS). The experimental results revealed that the prepared electrodes were well served as supercapacitors with a tremendous specific capacitance of MnO2 NFs VACNT/SS 1131 F/g at 0.25 A/g in 0.5 mol.L−1 Na2SO4, 518.8% more than VACNT/SS (218 F/g). Compared to other MnO2 NFs/CNT composites, as-fabricated binder-free MnO2 NFs/VACNTs electrode achieves outstanding performance with high initial discharge and charge capacities of...
Facile synthesis and simulation of MnO2 nanoflakes on vertically aligned carbon nanotubes, as a high-performance electrode for Li-ion battery and supercapacitor
, Article Electrochimica Acta ; Volume 390 , 2021 ; 00134686 (ISSN) ; Abnavi, A ; Ghasemi, F ; Ghasemi, S ; Sanaee, Z ; Mohajerzadeh, S ; Sharif University of Technology
Elsevier Ltd
2021
Abstract
This study reports the successful fabrication of high-performance flexible binder-free lithium-ion battery anode and supercapacitor based on the synthesis of 3D hierarchical MnO2 nanoflakes (NFs) on vertically aligned carbon nanotubes (VACNTs) grown upon stainless steel (SS). The experimental results revealed that the prepared electrodes were well served as supercapacitors with a tremendous specific capacitance of MnO2 NFs VACNT/SS 1131 F/g at 0.25 A/g in 0.5 mol.L−1 Na2SO4, 518.8% more than VACNT/SS (218 F/g). Compared to other MnO2 NFs/CNT composites, as-fabricated binder-free MnO2 NFs/VACNTs electrode achieves outstanding performance with high initial discharge and charge capacities of...
The decoration of TiO2/reduced graphene oxide by Pd and Pt nanoparticles for hydrogen gas sensing
, Article International Journal of Hydrogen Energy ; Volume 37, Issue 20 , October , 2012 , Pages 15423–15432 ; Ghasemi, S. (Shahnaz) ; Irajizada, A. (Azam) ; Akhavana, O. (Omid) ; Gholami, M. R. (Mohammad Reza) ; Sharif University of Technology
2012
Abstract
Reduced graphene oxide (RGO) was used to improve the hydrogen sensing properties of Pd and Pt-decorated TiO2 nanoparticles by facile production routes. The TiO2 nanoparticles were synthesized by sol–gel method and coupled on GO sheets via a photoreduction process. The Pd or Pt nanoparticles were decorated on the TiO2/RGO hybrid structures by chemical reduction. X-ray photoelectron spectroscopy demonstrated that GO reduction is done by the TiO2 nanoparticles and Ti–C bonds are formed between the TiO2 and the RGO sheets as well. Gas sensing was studied with different concentrations of hydrogen ranging from 100 to 10,000 ppm at various temperatures. High sensitivity (92%) and fast response time...
Design of Water Conveyance Systems Route Applying Satellite Images, Geographic Information System(GIS) & Genetic Algorithm
, M.Sc. Thesis Sharif University of Technology ; Shamsai, Abulfazl (Supervisor)
Abstract
To reduce construction costs selecting the optimal route for water conveyance line entails ample observation and considering all effective parameters. Some part of Aidoghmoush dam project of water conveyance line located in Azerbijan the east has been investigated in this research. First, by investigating, effective factors in determining the optimal route have been identified and then categorized into two groups of quantitative criteria(technical-economical) and qualitative criteria(environmental). Quantitative objectives include: slope, transportation system, infrastructures, fault and soil type. Qualitative objectives include: environmental considerations, land use and land cover. Because...
The Comparative Study of Nanotechnology Research and Development in The World Selected Countries
, M.Sc. Thesis Sharif University of Technology ; Ghasemi, Farhad (Supervisor)
Abstract
Nanotechnology requires a number of infrastructures for reaching its sustainable development. For each step of its development , various infrastructures should be studied and prepared in advance.In this direction, by introducing and recognizing the priority of Iran Nanotechnology R&D indexes ,the present research is going to propose an effective help. In this case, after studying the related literature and gathering the needed data , 27 indexes were recognized. Then , the indexes were divided in 7 criteria.In order to find the priority of the applied indexes , Fuzzy Multiple Criteria Decision Making (FMCDM) was applied. As the weighting of 7 criteria had been found by FANP , the...
Measurement of Gini Coefficients by Means of Household’s Special CPI in Iran(1984-2005)
, M.Sc. Thesis Sharif University of Technology ; Nili, Masoud (Supervisor)
Abstract
Gini coefficient is the most prevalent index for the measurement of inequality and is usually extracted by means of nominal variables based on income or expenditures of households. In this study we have extracted more accurate Gini coefficients. By using the raw data of Households Budget Survey (HBS) and STATA software, a special CPI for each household of the sample is extracted. Subsequently nominal expenditures are deflated by these special CPIs, and at last, Gini coefficients are extracted from real expenditures. Our findings indicate that in recent years, extracted Gini coefficients are remarkably higher than prevailing ones.
Obstacle Avoidance Control Algorithm for Multi Agent Autonomous Underwater Vehicle
, M.Sc. Thesis Sharif University of Technology ; Sayyaadi, Hassan (Supervisor)
Abstract
According to the importance of obstacle and collision avoidance for multiple Autonomous underwater vehicle (AUV) that are synchronized for starting the path following, in this study the coordination path following controller for a group of underactuated underwater vehicle with considering of obstacle and collision avoidance presented. The proposed control method is based on graph theory and back stepping with modeling of obstacle using limit cycle. At first, for controller design the back stepping method for path following of one AUV is used. Then the designed controller using of principles of graph theory, has been extended for multiple AUV and as the result multiple AUV is synchronized and...