Sharif Digital Repository

Techniques of production data analysis for single-phase oil and gas reservoirs have advanced significantly over the past few years. These techniques range from traditional (i.e., Arps, 1945; Fetkovich, 1980) to modern methods that account for the variation of operating conditions at the wellbore. However, the application of these later methods to gas condensate reservoirs is a challenge. The authors aimed to extend the applicability of modern production data analysis (single-phase flow) to analyze the production data of a gas condensate reservoir (two-phase flow). A single-phase production model consists of (a) a material balance equation, (b) the solution of diffusivity equation for gas... 

Techniques of production data analysis for single-phase oil and gas reservoirs have advanced significantly over the past few years. These techniques range from traditional (i.e., Arps, 1945; Fetkovich, 1980) to modern methods that account for the variation of operating conditions at the wellbore. However, the application of these later methods to gas condensate reservoirs is a challenge. The authors aimed to extend the applicability of modern production data analysis (single-phase flow) to analyze the production data of a gas condensate reservoir (two-phase flow). A single-phase production model consists of (a) a material balance equation, (b) the solution of diffusivity equation for gas... 

Techniques of production data analysis for single-phase oil and gas reservoirs have advanced significantly over the past few years. These techniques range from traditional (Arps and Fetkovich) to modern (for the variation of operating conditions at the wellbore). The application of these techniques for analysis of the production data of a gas condensate reservoir may not yield reliable answers due to the fact that the flow of fluid in gas condensate reservoirs is not single-phase. This paper presents the treatment of a modern method of production data analysis (single-phase flow) to analyze the production data of a gas condensate reservoir (two-phase flow). For this purpose, a single-phase... 

Techniques of production data analysis for single-phase oil and gas reservoirs have advanced significantly over the past few years. These techniques range from traditional (Arps and Fetkovich) to modern (for the variation of operating conditions at the wellbore). The application of these techniques for analysis of the production data of a gas condensate reservoir may not yield reliable answers due to the fact that the flow of fluid in gas condensate reservoirs is not single-phase. This paper presents the treatment of a modern method of production data analysis (single-phase flow) to analyze the production data of a gas condensate reservoir (two-phase flow). For this purpose, a single-phase... 

Well deliverability is an important issue in forecasting the performance of many gas condensate reservoirs. Condensate accumulations near the wellbore may cause a significant reduction in the well productivity, even in the case of very lean fluids. Generally, the well deliverability is affected by two pressure-drop sources due to depletion and condensate buildup. Recently rapid spreadsheet tools have been developed to evaluate the well performance using material balance equation for depletion and two-phase pseudo pressure integral for well inflow performance. Most of them account for the effects of negative inertia and positive coupling in the calculation of gas relative permeabilities. This... 

Well deliverability is an important issue in forecasting the performance of many gas condensate reservoirs. Condensate accumulations near the wellbore may cause a significant reduction in the well productivity, even in the case of very lean fluids. Generally, the well deliverability is affected by two pressure-drop sources due to depletion and condensate buildup. Recently rapid spreadsheet tools have been developed to evaluate the well performance using material balance equation for depletion and two-phase pseudo pressure integral for well inflow performance. Most of them account for the effects of negative inertia and positive coupling in the calculation of gas relative permeabilities. This... 

Blood vessels, especially large vessels have a greater thermal effect on freezing tissue during cryosurgery. Vascular networks act as heat sources in tissue, and cause failure in cryosurgery and reappearance of cancer. The aim of this study is to numerically simulate the effect of probe location and multiprobe on heat transfer distribution. Furthermore, the effect of nanoparticles injection is studied. It is shown that the small probes location near large blood vessels could help to reduce the necessary time for tissue freezing. Nanoparticles injection shows that the thermal effect of blood vessel in tissue is improved. Using Au, Ag and diamond nanoparticles have the most growth of ice ball... 

In this work, the effects of the surface-modified nanodiamond particles (NDs) on the barrier, rheological, mechanical and thermal properties of ethylene vinyl acetate (EVA) composites for the packaging applications were investigated. Fourier transform infrared spectroscopy, as well as thermal gravimetric analysis were employed to study the grafting of vinyltriethoxy silane (VTS) on the surface of NDs. Afterwards, EVA samples containing 0, 0.1, 0.5, 1, 1.5 and 2 wt% of surface-modified NDs were prepared by a two-stage process including the solution and injection processes. In order to evaluate the physicochemical, rheological, mechanical and thermal properties of the EVA/NDs samples, field... 

The effect of temperature, pressure and bonding time on microstructure of temperature gradient transient liquid phase (TGTLP) diffusion bonded Al7075 alloy using liquid gallium interlayer was investigated. The selected bonding method relies on using the minimum amount of liquid gallium on faying surfaces, using a very fast heating rate to reach the joining temperature and imposing a temperature gradient across the bond region. The microstructure of the diffusion bonded joints was evaluated by light optical microscopy, scanning electron microscopy and energy dispersive spectroscopy (EDS). Results show that by increasing the temperature, pressure and time of joining, a more uniform... 

A major problem in real-time packet-based communication systems, is misrouted or delayed packets which results in degraded perceived voice quality. If packets are not available on time, the packets are considered as lost. The easiest solution in a network terminal receiver is to replace silence for the duration of lost speech segments. In a high quality communication system, to avoid degradation in speech quality due to packet loss, a suitable method or algorithm is needed to replace the missing segments of speech. In this paper, we introduce an adaptive filter for replacement of lost speech segment. In this method Kalman filter as a state-space based method will be used to predict the... 

The compound, alkaline lead acetate, Pb(CH3COO)2·PbO·H2O (ALA), was purchased from the Fluka Company. The X-ray diffraction film and SEM electron microgaph of this compound were obtained and reported in this paper for the first time. The thermal behavior of alkaline lead acetate (ALA) was studied using thermogravimetery (TGA) and Differential Scanning Calorimetery (DSC) techniques under an O2 gas atmosphere from 25 to 600°C. Four distinct energy changes associated with weight changes were observed, all of them being exothermic in the DSC results. The amount of ΔH for each peak is reported. © Sharif University of Technology  

Using two techniques of thermogravimetry and differential scanning calorimetry under O2 gas atmosphere from 25 to 600°C, the thermal behavior of laboratory-produced compound lead(IV) oxide α-PbO2 was investigated. The identity of products at different stages were confirmed by XRD technique. Both techniques produced similar results supporting the same decomposition stages for the compound. Three distinct energy changes were observed, namely, two endothermic and one exothermic in DSC. The amount of ΔH for each peak is also reported. © 2008 Springer Science+Business Media, LLC  

In this study, the effects of the type and content of reactive diluents on the permeation/separation of carbon dioxide/nitrogen (CO2/N2) through acrylate-terminated polyurethane (APU)-acrylate/acrylic diluent (APUA) composite membranes was investigated. A series of APUs based on poly(ethylene glycol) (PEG)-1000 g mol−1, toluene diisocyanate, and 2-hydroxyethyl methacrylate was synthesized and then diluted with several reactive diluents. The results obtained from differential scanning calorimetry (DSC) and Fourier transform infrared analyses showed that the microphase interference of hard and soft segments increased with increasing reactive diluent content. Furthermore, with increasing alkene... 

The compound, lead hydroxide Pb6O4(OH)4, was prepared by a method used for the first time in the authors laboratory. The compound was identified by XRD and it's purity was determined by analytical methods (100%). The thermal characteristics of this compound were investigated by using a thermogravimetry (TGA). This compound was found to be stable at room temperature and at 160°C will decompose completely to produce lead (II) oxide. © Sharif University of Technology, April 2007  

The effects of hydrophilic and hydrophobic nanosilica (SiO2) on the morphology, mean diameter distribution of fibers, mechanical and piezoelectric properties of poly (vinylidene fluoride) (PVDF) nanofibers were studies. We prepared Nanofibers by the electrospinning of PVDF solutions containing 1.5 wt.% both hydrophilic and hydrophobic nano-SiO2 loadings. Morphology and diameter distribution of the electrospun nanofibers were studied using field emission scanning electron microscopy (FE-SEM) analysis. Tensile test was used to study the effect of both types of nanosilica on the tensile strength, young's modulus and strain at break. Piezoelectric characterization of the electrospun fibers were... 

In order to determine the activity of C137s in soil resulting from nuclear accidents or fallouts, the best choice is to use HPGe detectors due to their best energy resolutions. In this regard, in order to enhance the detection efficiency, the Marinelli beakers have been used to increase the radiation interaction with the sensitive volume of the detector. In previous works, to optimize the dimension of Marinelli beakers, the assumption was that the emission rate of the source is homogeneous in beaker volume. In the present study, to investigate the effect of the inhomogeneous emission rate of the source on the optimum dimensions of the beaker, in a simple case, the beaker was divided into two... 

Background: Nowadays, study and application of modified membranes for water treatment have been considered significantly. The aim of this study was to prepare and characterize a polysulfone (PSF)/graphene oxide (GO) nanocomposite membrane and to evaluate for arsenate rejection from water. Materials and methods: The nanocomposite PSF/GO membrane was fabricated using wet phase inversion method. The effect of GO on the synthesized membrane morphology and hydrophilicity was studied by using FE-SEM, AFM, contact angle, zeta potential, porosity and pore size tests. The membrane performance was also evaluated in terms of pure water flux and arsenate rejection. Results: ATR-FTIR confirmed the... 

IN738LC is one of the superior nickel base superalloys utilized at high temperatures in aggressive environments. However, experiencing high temperatures and stresses during service causes microstructure deterioration and degradation of mechanical properties in this alloy. To restore the microstructure and mechanical properties of the degraded alloy, rejuvenation heat treatments can be considered. In this study, the evolution of microstructural features in a creep damaged IN738LC superalloy during different stages of rejuvenation heat treatment cycles was investigated. During solution treatment stage, dissolution of coarsened γ′ precipitates, grain boundary films and transition zone around... 

The present study investigates the evolution of γ′ precipitate microstructure in a creep damaged IN738LC superalloy during different stages of rejuvenation heat treatment cycles. Dissolution of coarsened γ′ precipitates in the creep damaged alloy occurred during different solution treatments. The precipitates that did not dissolve completely during solution treatment and those formed during subsequent cooling were considered to be as remnant and cooling precipitates respectively. It was found that higher solution treatment temperatures result in lower volume fraction of remnant precipitates and further formation of cooling precipitates. Slower cooling rates after solution treatment gave the...